2002-2003 Acura RSX Icebox Cold Air Intake Installation Instructions

Download Honda Civic Si & Acura RSX Icebox Cold Air Intake Installation Instructions (2002-2003 Honda Civic Si) (2002-2003 Acura RSX—All) Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan. •Remove ground strap bracket on side of transmission (C). Relocate ground strap from transmission bracket to top of transmission (D). Step #2 Install Comptech Airbox •Install (3) stock rubber grommets* (E) through large holes on underside of mounting ears on Icebox (a small dab of filter oil may be used to ease this process).… Read More

2002 – 2003 Honda Civic Si & Acura RSX Comptech Icebox Cold Air Intake Installation Instructions

Download Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX). Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

Honda Civic Si Acura RSX Icebox Cold Air Intake Manual Installation Instructions

Download
Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX).
Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions

Download
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More

Audi A8 Parrot 3100 Bluetooth Kit Installation Instructions

Download Installing a Parrot 3100 Bluetooth Kit in a D3 Audi A8. This procedure is to be used in conjunction with the audipages.com checklist, wiring diagram and wiring table supplied with your kit. Remove Fuse SB13 Remove the left hand side fuse panel. This is accomplished by popping the cover off with a trim stick. Once complete, REMOVE fuse SB13 (the fuse labled 13) , which is the unswitched power to the Telematics/telephone box before starting. This will prevent inadvertent grounding of the power supply during installation. Remove Trim and Telematics Box Remove the door kick panel trim by prying it up on the aft portion of it and unclipping it, then pull the vertical portion out, it just clips out. Remove the driver’s side floor mat. Using a Torx T-35 screwdriver, remove the screw that holds the left foot rest in place. Be careful when removing the screw not to drop it down into the floor board.… Read More

2002-2006 ACURA RSX Type-S Intake System PART 21-506

Download PART NUMBER: 21-506 2002-2006 ACURA RSX Type-S L4-2.0L C. A. R. ine has run in the past two hours, let it cool down. d. Disconnect both the negative and positive battery terminals. e. Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle. Support your vehicle using properly rated jack stands before wheel removal or while working under the vehicle. NEVER WORK UNDER A VEHICLE WITHOUT USING JACK STANDS. i. Remove the front left wheel. ii. Remove the left fender well lining and remove the lower splashguard. f. This intake system includes a replacement windshield washer system. g. Do not discard stock components after removal of the factory system. 2. Removal of stock system a. Factory air box system. b. Remove the two mounting bolts securing the upper engine cover. Remove the engine cover. c.… Read More

2002 Acura RSX 555I Honda/Acura Immobilizer Bypass Module

Download Honda Civic 2001-2002 Acura RSX 2002. Installation Instructions 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the wiring color guide. 3. Wire the 555I as shown in the wiring diagram. IMMOBILIZER IGNITION FEEDYELLOW/BLACK DATA RED/BLUE KEY SENSE RED/WHITE RED: Connect this wire to a constant (+)12 volt source. BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. BLUE: Connect this wire to the BLUE status output of the remote start. It must see ground during remote start. BLUE/WHITE: Connect this wire to the (-) key sense wire listed in the Wire Color Guide. It is located in a six-pin molex at the ignition cylinder. The key sense wire rests at ground when the key is inserted into the ignition switch.… Read More

2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

2006 ACURA RSX GOLD EMBLEM KIT INSTALLATION INSTRUCTIONS

Download Be careful not to damage the body paint finish, bumpers, bumper grilles, etc. •This gold emblem kit should be installed only if the ambient air temperature is 60°F (15°C) or above. Installing the Front “A” Emblem 1. Open the hood, and remove the front bumper (12 clips, four screws, and two self-tapping washer-screws). To prevent damage to the front bumper, place it on a blanket. 2. Inside the engine compartment, remove the two secure self-tapping screws that secure the emblem base to the front grille, and remove the emblem base. 3. Using diagonal cutters, cut the locating tabs from the existing front “A” emblem. Push the locating tabs to remove the emblem from the emblem base. 4. Using isopropyl on a shop towel, clean the area where the emblem was removed. 5. Install the gold “A” emblem on the emblem base by inserting the two locating tabs into the holes in the emblem base.… Read More

2002-2006 Acura RSX-S Throttle Body To Intake Manifold Adapter

Download Part #: KIM01 K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB Intake Manifold Adapter This adapter provides the SOLUTION for directly bolting up a 02-06 RSX-S/ITR or 02-05 Civic Si/CTR Throttle Body to an Accord Euro R, 06-08 Civic Si, or 04-05 TSX Intake Manifold. Ease of fitment has been confirmed for the following vehicle/engine/mount combinations: -1992-199 5 Honda Civics equipped with a K20 engine and Hasport EGK1 engine mounts -1996-200 0 Honda Civics equipped with a K20/24 engine and Hasport EKK2 engine mounts -1994-200 1 Acura Integras equipped with a K20 engine and Hasport EGK1 engine mounts -2002-200 6 Acura RSX-S/Honda ITRs with a K20 engine and all available engine mounts. 1. PREPARATION 1. Remove the EVAP hose, brake booster hose, PCV hose, vacuum hose, water bypass hoses, throttle cable, fuel lines, fuel injector connectors, IAC valve connector, TP sensor connector, MAP sensor connector, and EVAP canister purge valve connector from your current intake manifold and throttle body setup.… Read More