acura integra type r tps issue

You search Auto repair manual PDF about acura integra type r tps issue, search results will appear below. If search results do not exist, please search by others keyword.

1997-2001 Acura Integra Type-R Racing Intake Manifold

Filed Under (Acura) by admin on 03-01-2014

Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More

2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Filed Under (Acura) by admin on 24-11-2013

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

1994-2001 Integra GSR/Type R Vtec Performance Amplifier Control Installation Instructions

Filed Under (Acura) by admin on 09-12-2013

Download Civic EX/Si 92-00, Del Sol Si/VTEC 92-95, Integra GSR/Type R 94-01,Prelude 97-01 S2000. Installation 1. Locate the original ECU. On most cars it is in the passenger side “kick panel” near the passenger’s feet. On the Prelude models, it is on the floor directly below the passenger’s feet. On the S2000 the ECU is located in the left side kick panel. 2. Locate the plugs needed for the VPAC wiring connections by looking at the illustration for your model and year. 3. Mount the VPAC using the “hook and loop” fastener tape to a convenient location on the dash or in the glove box. Route the wires to the ECU location. 4. Follow the instructions for your vehicle to complete the wiring. 5. Reinstall the ECU, ECU cover/kick panel/carpeting in the reverse order of removal. 6. Go have fun with your new VPAC. Civic EX/Si 92-95 and Del Sol SI/VTEC 92-95 1.… Read More

2000-2001 Acura Integra AEM EMS System Installation Instructions

Filed Under (Acura) by admin on 02-01-2014

Download EMS P/N 30-6051 (4 cylinder Acura/Honda vehicle with 6 cylinder engine and harness swap) Vehicle: 2000-2001 Acura Integra 1998-1999 Acura 2.3CL 1996-2000 Honda Civic Engine wiring harness: 1999-2002 Honda Accord V6 J30A1 1999 Acura CL 3.0L J30A 2001-2003 Acura CL 3.2L J32A1 (auto harness only) 1999-2003 Acura TL 3.2L J32A1 2002-2003 Acura CL/TL 3.2L Type S J32A2 (auto harness only) 2002-2004 Honda Odyssey 3.5L J35A4. Wiring accessories to the EMS: Please follow this suggested wiring diagram when adding/retaining original accessories such as the speedometer, reverse lockout, UEGO gauges, MAP sensors, IAT sensors, or switches for use with the EMS. Note that wire polarity is not important for the Air Temperature sensor. 1) Install AEMTuner software onto your PC The latest version of the AEMTuner software can be downloaded from the AEMTuner section of the AEM Performance Electronics forums. Series 2 units are not supported by the older AEMPro tuning software.… Read More

2007-2008 Acura TL Type S CABIN AIR FILTER IDENTIFICATION

Filed Under (Acura) by admin on 02-01-2014

Download Acura CSX, CSX Type S, MDX, RDX, RL, TL, TL Type S, TSX; Honda Accord, Accord Hybrid, Civic, Civic Hybrid, CR-V, Odyssey, Pilot, Ridgeline OE: 80292-SEC-A01 Fits: 2007-on Acura CSX, CSX Type S, MDX, RDX, Honda CR-V 2005-on Acura RL, Honda Odyssey 2004-on Acura TL, TSX 2007-08 Acura TL Type S 2003-on Honda Accord 2005-07 Honda Accord Hybrid 2006-on Honda Civic, Ridgeline 2 006-09 Honda Civic Hybrid 2009-on Honda Pilot. 1. Open passenger side door. 2. Open glove compartment. 3. Detach damper rod from glove compartment. 4. Push in on left and right sides of glove compartment to release glove compartment. If equipped with tabs: a. Close glove compartment part way to relieve pressure on tabs. b. Push in tabs on outside of glove compartment to release glove compartment. c. Remove tabs. 5. Remove screws on left and right sides (if equipped) while holding glove compartment. 6. Flip down glove compartment.… Read More

Acura Integra Fuel Pressure Gauge Set Installation Instructions

Filed Under (Acura) by admin on 04-03-2014

Download

Honda Civic/CRX/del Sol Acura Integra/NSX – Eagle Talon Mitsubishi Eclipse – Plymouth Laser Part Number 46054. INSTALLATION The fuel pressure tap on the late model Honda Civic/CRX/del Sol, Acura Integra/NSX, Mitsubishi Eclipse, Eagle Talon & Plymouth Laser is located on top of the fuel filter which is mounted on the passenger side firewall (driver’s side for the NSX). We suggest the vehicle be allowed to cool for a while before you begin since you will be working around the fuel system. CAUTION: THE FUEL SYSTEM CONTAINS FUEL UNDER HIGH PRESSURE EVEN WHEN THE ENGINE IS NOT RUNNING. BEFORE DISCONNECTING A FUEL LINE, WRAP THE FITTING WITH A RAG TO PREVENT FUEL SPRAY. Remove the fuel pump fuse from the fusebox. Try starting the vehicle several times until it will not remain running. This will help relieve pressure in the fuel system. (NOTE: For some vehicles it may be helpful to remove the battery).… Read More

1994-2001 Acura Integra GSR Whirlwind Intake Manifold

Filed Under (Acura) by admin on 31-12-2013

Download Acura GSR Whirlwind Intake Manifold Part No. 59002 (Polished) and 59003 (Satin) For use on 1994 – 2001 Acura Integra GSR 1.8L DOHC VTEC. Preparation for Installation – 1. Make sure that there are no metal chips or other debris inside the manifold. Check that all bolts will run freely into any tapped holes. 2. Note that while this manifold makes provision for all vacuum lines and other brackets or parts that attached to the stock manifold, the vacuum ports originally on the front side of the manifold have been moved to the back for a cleaner appearance. This will require the use of longer vacuum hoses in some cases. 3. Disconnect battery and drain coolant. 4. Mark and identify all hoses and valves. 5. Check the condition of all hoses, gaskets and o-rings. Replace as needed. Use a new intake gasket. Honda #17105-P72-004. Removal – 1. Relieve the fuel pressure in the system by loosening the banjo bolt on the top of the fuel filter.… Read More

1994-2001 Acura Integra Part EGJ1 HASPORT PERFORMANCE

Filed Under (Acura) by admin on 28-01-2014

Download Part Number EGJ1 for J-series V6 engines into 1992-1995 Honda Civic, 1994-1997 Del Sol And 1994-2001 Acura Integra. Things you should know about this swap The following is a list of information you should know before performing this swap. Please visit www.hasport.com for the latest information on this swap. 1. Ground and hood clearance – The J-series engine is a tall engine. It is much taller than the H22 and K-series engines. Hasport engine mounts are designed to hold the engine with the same ground clearance you would find on a K-series engine swapped vehicle. The engine sticks up several inches above the hood line. A custom or modified hood is needed. 2. Hasport does not make a conversion engine harness for the swap. 3. Power Steering – The Civic or Integra power steering hose will not work with the J-series power steering pump. Just like with K-series swaps, new power steering hoses need to be made and the reservoir will need to be relocated.… Read More

Honda / Acura Transponder Interface: TYPE “C”

Filed Under (Honda) by admin on 26-02-2014

Download DATA to DATA PORT (D 2D) : of D2D Cable plugs into the upgradeable vehicle interface module. OPTION A: – D2D Port used to connect to USB Bootloader adaptor & computer to download & flash vehicle interface firmware. OPTION B: – D2D Port used to connect to the data port of a remote control system equipped with ClearCode V ehicle I nterface P rotocol. Remote control systems designed with ClearCode VIP can securely communicate via the D2D cable to transmit & receive data commands which initiate specific vehicle function such as doorlocks & immobilizer override and /or request information from the vehicle such as status of entry points (doors) or ambiant température, diesel glow plug etc… ClearCode VIP represents the doorway to vehicle integration…As an enhanced security feature, this upgradeable vehicle interface module automatically detects when the Vehicle Interface Protocol is present and deactivates the analogue override input wire (brown wire) ensuring that this module can only be activated by an authorized user.… Read More

1994-2001 Acura Integra Racing Intake Manifold

Filed Under (Acura) by admin on 01-01-2014

Download 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt (2) lower intake manifold bolts that secure the manifold to the engine block. This bracket will still be used to accommodate the heater bypass pipe. Next, unbolt the manifold from the cylinder head. Remove the intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors. 4. Remove the intake air bypass (IAB) vacuum tank, check valve, and control solenoid valve.… Read More

You might also likeclose