1994 Chevy Truck C 1500 Ignition – Timing Connector Location Change

Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More

FORD LINCOLN MERCURY Satellite Radio Owners Manual Installation Instructions

Download 1. Introduction Thank you for purchasing the iSimpleĀ® Media Gateway. The Media Gateway is designed to provide endless hours of listening pleasure from your factory radio. To ensure that your SCC1 satellite radio tuner performs correctly with your radio, we recommend that you read this entire manual before attempting installation of the Media Gateway. The Media Gateway allows connectivity for Sirius Satellite Radio tuner (SCC1 sold seperately) enabling full control of this device from the factory installed radio. It also retains original system features such as rear seat entertainment (if equipped). 2. Precautions PREVENTING DAMAGE TO YOUR VEHICLE Some installations require you to make wiring connections. To eliminate the risk of an electrical short, we recommend disconnecting the vehicle’s battery prior to installation. If you do not feel comfortable making these connections, we suggest you seek professional installation. PROPER MOUNTING LOCATION Securely install the interface in a location free from: heat, humidity, moving parts, sharp metal edges or direct sunlight.… Read More

1997 Chevy Truck C Tahoe Interior Lighting Module Locations

Download 1997 Chevy Truck C Tahoe 2WD V8-5.7L VIN R View: Under Center Of Instrument Panel Zoom Sized for Print Interior Lamp Control Module, Remote Control Door Lock Receiver Manufacturer supplied 2 different possible locations. Look for 5 wire connector with wire colors: gray, white, orange, pink & black. #PIT3819: Location of Interior Lamp Control Module – keywords control dim dome electrical entry ground illumination inoperative keyless lens light remort resistor RKE short – (Dec 23, 2005) Subject: Location of Interior Lamp Control Module. Models: 1995-2000 Chevrolet C/K Trucks, Suburban and Tahoe 1995-2000 GMC Yukon and C/K Trucks Classic Body Style Only The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this P1. Condition/Concern When diagnosing a dome lamp concern on one of the vehicles listed above, you may be unable to locate the Interior Lamp Control Module that is called out in the Service Manual.… Read More

2004 Chevrolet Chevy Suburban Gradual Coolant Loss Over Time with No Evidence of Leak Found

Download 2004 Chevrolet Chevy Suburban – 4WD | Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) Service Manual. Information on Gradual Coolant Loss Over Time with No Evidence of Leak Found. Models: 2004-2006 Buick Rainier 2001-2006 Cadillac Escalade Models 2001-2006 Chevrolet Avalanche, Blazer, Silverado, Suburban, Tahoe, TrailBlazer Models 2001-2006 GMC Envoy, Jimmy, Sierra, Yukon Models 2001-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.8L or 5.3L VORTECĀ® GEN III, GEN IV V8 Engine (VINs V, T, M, B, Z – – RPOs LR4, LM7, LH6, L33, L59) Some vehicles may experience a gradual coolant loss over time. A very low percentage of cylinder head(s) manufactured with an embossed Castech logo may develop a porosity crack in a very specific area. Inspect the cylinder head assembly to determine if the casting was manufactured by Castech. This can be accomplished by inspecting for their casting logo located on top of the intake port, under the rocker arm support rail and in the spring deck cavity portion of the cylinder head.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

2001 Chevrolet Chevy K Silverado Transmission Stuck in Second or Third Gear

Download Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit ) Models: 2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) Condition Some customers may comment on one or more of the following conditions: Upon investigation, one or all of the diagnostic trouble codes (DTCs) P0740, P0753, P0758, P0785, P0787, P0973, P0976, P1860, P2761, P2764 and P2769 may be set depending on the vehicle. Cause The most likely cause of this condition may be a loss of voltage to the transmission solenoid power supply circuit. This condition may also be the result of an incorrect installation of an aftermarket electronic device such as a remote starter or alarm system.… Read More

2009-2010 Ford Expedition LOW FREQUENCY ENGINE KNOCKING NOISE AT HOT IDLE

Download 2009-2010 Ford Expedition LOW FREQUENCY ENGINE KNOCKING NOISE AT HOT IDLE. FORD: 2009-2010 Expedition, F-150 LINCOLN: 2009-2010 Navigator. 6. Open Data Logger. ISSUE Some 2009-2010 F150 vehicles equipped with a 7. Select Powertrain Engine. 4.6L 3V or 5.4L 3V engine, Expedition and Navigator vehicles may exhibit a low frequency 8. Select PCM Data Logger. knocking noise from the engine at hot idle only. The 9. Clear the preselected items by clicking the noise is predominately heard from the right front eraser icon button. wheel well area and/or the right hand (RH) engine cam cover. This noise may be generated from the 10. Select variable cam timing desired angle RH variable camshaft timing (VCT) phaser number (VCT_DSD). assembly. This procedure was created to diagnose the RH VCT phaser assembly. 11. Go to live display and press the tick mark. 12. Make sure the parameter identification (PID) is ACTION highlighted with the dark lines above and below Follow the Service Procedure steps to correct the the data being displayed.… Read More

2008-2010 FORD FOCUS ELECTRONIC CRUISE KIT 250-1840

Download 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting. Figure 1 2. Remove the driver side lower dash and kick panels. Remove the steering wheel shroud. Figure 2 B. Install Electronic Module 1. Plug in the Main Wiring Harness, Switch Harness, and Pedal Interface Harness onto mating connectors of the Cruise Control Module. Figure 3 2. Place the Cruise Control Module in a secure location behind the driver side dash area near the firewall away from moving parts. Secure with supplied wire ties. 3. Route the Pedal Interface Harness through steering column and down to the accelerator. 4. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of Pedal Interface Harness. Apply the other connector to the accelerator.… Read More

2010 ACURA TSX STEERING WHEEL INSTALLATION INSTRUCTIONS

Download TOOLS AND SUPPLIES REQUIRED Phillips screwdriver 14 mm T-handle wrench T30 TORX wrench Steering wheel puller Service manual Torque wrench Plastic trim tool (T/N: SILTRIMTL10) 10 mm Wrench Adhesive steering wheel offset gage sticker (T/N: 07AAJ-001A300) 1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the audio presets. 2. Disconnect the negative cable from the battery, and wait at least 3 minutes before you start to install the steering wheel. 3. Remove the access panel from the underside of the driver’s side airbag. 4. Remove the airbag connector from the switch plate. 5. Unplug the airbag connector. Pull the spring-loaded sleeve toward the stop while holding the opposite half of the airbag connector, then pull the airbag connector halves apart. Be sure to pull on the sleeve and not on the harness wires. 6. Remove and discard the two TORX bolts that secure the airbag, and remove the airbag.… Read More

1999 Chrysler Truck Blend Door Actuator Replacement

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More