2001 Buick Regal Power Steering Pump Replacement

Download 2001 Buick Regal V6-3.8L VIN K Vehicle Level Steering and Suspension Steering Power Steering Pump Service and Repair Power Steering Pump Replacement. Removal Procedure 1. Place a drain pan under the vehicle. 2. Remove the accessory drive belt. Refer to Drive Belt Replacement in Engine. 3. Raise and support the vehicle. Refer to Vehicle Lifting . 4. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. 5. Remove the power steering pressure hose from the power steering pump. Refer to Power Steering Pressure Hose Replacement. 6. Remove the power steering return hose from the power steering pump. Refer to Power Steering Return Hose Replacement. 7. Remove the power steering mounting bolts from the power steering pump. 8. Remove the power steering pump. 9. Remove the power steering pump reservoir from the power steering pump. 10. Transfer the power steering pump pulley. Refer to Power Steering Pulley Replacement Installation Procedure 1.… Read More

2002 Chrysler Voyager LX ACCESSORIES and EQUIPMENT Power Windows

Download TROUBLE SHOOTING Inspect power window circuit breaker (25-amp), located in left kick panel. Inspect fuse No. 28 (40-amp) in Intelligent Power Module (IPM). IPM is located on left side of engine compartment. Inspect ground at right “B” pillar. SYSTEM TESTS ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay.… Read More

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent

Download 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual Subject: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Models: 2005 Buick Allure (Canada Only), LaCrosse 2004-2005 Pontiac Grand Prix. 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual | Document ID: 1644694 #05-01-39-001A: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) – (Apr 6, 2005) This bulletin is being revised to update Step 5 of the service procedure. Please discard Corporate Bulletin Number 05-01-39-001 (Section 01 — HVAC). Condition Some customers may comment on an inoperative or intermittent Heating, Ventilation and Air Conditioning (HVAC) blower motor. Others may comment that the blower motor speed may momentarily drop or that the blower motor continues to run after the key is turned off.… Read More

PEUGEOT 407 e253 CAR ALARM CONTROL UNIT

Download
LOCATION OF THE CAR ALARM CONTROL UNIT Compact control units and sirens: place under the bonnet on the wheel box on the driver’s side. Modular control units and accessories: place under the dashboard on the driver’s side. CAR ALARM SUPPLY Positive: Connect the Can Bus connector in the kit of accessories supplied with the e253 (see instructions for its connection in following pages). Power is taken from the Red wire (Pos. 1). Negative: Connect the Can Bus connector in the kit of accessories supplied with the e253 (see instructions for its connection in following pages). Earth is taken using the Black wire (pos. 2) IMMOBILISER Starter Motor: Cut the White wire (Pos 3) in the Black 3-pin connector under the steering wheel. ODOMETER Connect to pos 26 (Wire N° 6739) in the black 40 way connector (green part) on the BSI control unit or directly to the ABS control unit under the bonnet next to the battery in pos.… Read More

1996-2000 Honda Civic 2-door Front Windows Bind

Download 1. Remove the door panel. Refer to section 20 of the 1996-00 Civic Service Manual. 2. Remove the armrest bracket, then pull down the plastic cover to gain access to the window regulator. 3. Carefully move the glass until you can see the glass mounting bolts, then loosen them. Slide the guide rearward, remove the glass from the guide, and carefully pull the glass out through the window slot. 4. Check the year and VIN. If the vehicle is a 1996 or 1997 within the affected VIN range, replace the window regulator. Go to step 5. If the vehicle is not a 1996 or 1997 within the affected VIN range, go to step 8. 5. Remove the two roller guide bolts and the two rear regulator mounting bolts; then remove the front regulator mounting bolts. 6. Disconnect the power window motor connector, and detach the harness clip (if applicable); then lift and remove the regulator through the opening in the door.… Read More

2001 PEUGEOT 306 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, driver’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 2 mm2 RED wire located at the position nr. 1 in the 15 way black connector of the central unit of the central locking placed under the central tunnel. – 31: connect directly to the car body. As alternative, connect directly to the negative pole of the battery. IGNITION WIRE + 15/54: connect to the wire located at the position nr. 5 of the 15 way black connector of the central unit of the central locking placed under the central tunnel. DIRECTION INDICATORS Connect to the WHITE wire at the position nr. 10 and to the BEIGE wire at the position nr. 2 located in the 15 way black connector of the central unit of the central locking placed under the central tunnel.… Read More

2006 Ford Truck F 150 Body – Slow Power Window Operation

DownloadPOWER WINDOW SLOW UPWARD TRAVEL FORD: 2005-2007 F-150 LINCOLN: 2006-2007 Mark LT ISSUE Some 2005-2007 F-150 and 2006-2007 Mark LT vehicles equipped with power windows may experience a customer concern of slow power window travel when raising the window; it may be due to a concern with the alignment of the window glass. SERVICE PROCEDURE 1. Lower the window completely, and measure the amount of time it takes for the glass to travel from the fully open to fully closed position. a. If the time is less then six (6) seconds then DO NOT perform this TSB. b. If the time required to move the glass from the fully open to fully closed position is greater than six (6) seconds, continue with this TSB. 2. Inspect the glass runs to make sure they are not wavy and causing additional resistance to the glass. 3. Remove the door panel following Workshop Manual (WSM), Section 501-05, access the glass clamps through the openings in the door sheet metal.… Read More

2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Download 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9.… Read More

FORD FOCUS POWER WINDOW INSTALLATION INSTRUCTIONS

Download Tools & Materials Needed: 1. Utility Knife 2. Wire Crimper 3. Torx™ Wrenches 4. Hex Nut Drivers 5. Drill and Bits 6. Phillips Head Screw Driver 7. Crank Spring Removal Tool (Special Tool, available at most Auto Parts Stores) – or – 8. Flat Screw Drivers (2) 9. Add-A-Circuit ™ fuse adapter 10. Silicon Sealant (Clear or Black) Procedure: (Approximate time to complete installation: 3 – 4 hours) A. Removing the Door Panel Coverings 1. For ease of installation, do both sides at the same time. 2. Roll the windows to approximately 1/2 open, and so the crank handle is in the Down Position. With either the Crank Spring Removal Tool, or a flat Screwdriver, remove the spring, located in a slot on the back of the crank. 3. Remove the cover plate for the remote-control mirror, which is held in place by 3 spring clips. Remove by gently pulling the front corner of the cover out, and then slide the cover back.… Read More

Steering Vibration/Shudder During Parking Manuever

Download Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville. Condition Some customers may comment on a steering vibration, shudder or moan noise when steering during parking maneuvers on dry pavement. Correction Install a new power steering pressure (inlet) hose assembly on the following vehicles: Install a new power steering pressure (inlet) and return (outlet) hose assembly on the following vehicles: Diagnosis Important: In diagnosing the above listed vehicles, do not overlook other obvious repairs prior to replacing the hose(s). 1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions.… Read More