98 buick regal power steering pump repair

You search Auto repair manual PDF about 98 buick regal power steering pump repair, search results will appear below. If search results do not exist, please search by others keyword.

2001 Buick Regal Power Steering Pump Replacement

Filed Under (Buick) by admin on 01-01-2014

Download 2001 Buick Regal V6-3.8L VIN K Vehicle Level Steering and Suspension Steering Power Steering Pump Service and Repair Power Steering Pump Replacement. Removal Procedure 1. Place a drain pan under the vehicle. 2. Remove the accessory drive belt. Refer to Drive Belt Replacement in Engine. 3. Raise and support the vehicle. Refer to Vehicle Lifting . 4. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. 5. Remove the power steering pressure hose from the power steering pump. Refer to Power Steering Pressure Hose Replacement. 6. Remove the power steering return hose from the power steering pump. Refer to Power Steering Return Hose Replacement. 7. Remove the power steering mounting bolts from the power steering pump. 8. Remove the power steering pump. 9. Remove the power steering pump reservoir from the power steering pump. 10. Transfer the power steering pump pulley. Refer to Power Steering Pulley Replacement Installation Procedure 1.… Read More

Steering Vibration/Shudder During Parking Manuever

Filed Under (Other Manuals) by admin on 07-02-2014

Download Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville. Condition Some customers may comment on a steering vibration, shudder or moan noise when steering during parking maneuvers on dry pavement. Correction Install a new power steering pressure (inlet) hose assembly on the following vehicles: Install a new power steering pressure (inlet) and return (outlet) hose assembly on the following vehicles: Diagnosis Important: In diagnosing the above listed vehicles, do not overlook other obvious repairs prior to replacing the hose(s). 1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions.… Read More

2000 Volkswagen Cabrio Ignition Switch: Service and Repair

Filed Under (Volkswagen (VW)) by admin on 02-01-2014

Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More

1993 Ford Escort FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH)

Filed Under (Ford) by admin on 31-12-2013

Download 1993 Ford Escort G – TESTS W/CODES – EEC-IV (1.9L)’ ’1993 ENGINE PERFORMANCE Ford Motor Co. – Self-Diagnostics – EEC-IV. CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH) Diagnostic Aids When ignition switch is in the ON or START position, the PCM connects FUEL PUMP circuit (PCM terminal No. 22) to ground. The fuel pump relay is energized and electrical current flows to the fuel pump. If PCM does not receive ignition PIP signal within 2 seconds, FUEL PUMP circuit is opened and fuel pump operation is terminated. Perform this test when instructed by QUICK TEST or CIRCUIT TEST AA. This test is only intended to diagnose: * Fuel pump relay. * Inertia Fuel Shutoff (IFS) switch. * Wiring harness circuits (B+, VPWR, FUEL PUMP, GND and POWER-TO-PUMP). * Faulty Powertrain Control Module (PCM). Fig. 31: Fuel Pump Monitor Circuit Diagram (Escort & Tracer) 1)Code 87/556: Check VPWR To Fuel Pump Relay Code 87/556 indicates a fuel pump primary circuit failure.… Read More

2.0L FORD FOCUS Supercharger System Installation Instructions

Filed Under (Ford) by admin on 31-12-2013

Download 2.0L FORD FOCUS Supercharger System Installation Instructions 2000-2003 ZX3 Model 2002-2003 SVT Model. A. Remove the ducting between the air box and the throttle body. Disconnect the MAF from the ducting and set aside. B. Remove the air box, fresh air tube, battery, battery box and all remaining components running to the inlet of the motor. C. Remove the Battery/Air Box support bracket: 1. Support the driver’s side of the transmis- sion. 2. Remove four nuts securing the bracket to the driver’s side engine mount. 3. Remove the large central nut securing the transmission to the engine mount. 4. Lift the plate on top of the engine mount and remove the Battery/Air Box support bracket. (See Fig. 1-a .) 5 . Reinstall the engine mount plate and resecure all engine mount hardware. D. Place an oil drain pan beneath the power steering pump. Disconnect the high-pressure (3/8″ tube) power steering line from the power steering pump.… Read More

2003 BMW 325I Sport Wagon Check engine light on and fault codes stored

Filed Under (BMW) by admin on 19-03-2014

Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More

Fuel Pump Timing General Information

Filed Under (Other Manuals) by admin on 10-12-2013

Download Pump timing that is off by only a few crankshaft degrees will cause: Poor performance – starting and power. 1. Excessive smoke. 2. Poor fuel economy. 3. Time Engine pump timing begins with the timing of the fuel injection pump drive gear to the camshaft gear. The first step is the location of TDC of the compression stroke for cylinder Number 1. Then, depending on the engine configuration, an alpha character on the injection pump drive gear will possibly need to be aligned with the mark on the camshaft gear. To verify that the fuel injection pump is timed correctly, first check the alignment marks on the pump flange and gear housing. NOTE: 1 mm of rotation past the timing mark will advance or retard (depending on direction of rotation) the pump timing by 1 degree. The Lucas CAV DPA, DPS, Delphi DP210, Stanadyne DB4, and the Bosch® VE fuel injection pumps all have a provision for locking the pump shaft at a position corresponding to top dead center for cylinder Number 1.… Read More

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE

Filed Under (Toyota) by admin on 04-04-2013

Download 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear.… Read More

1995 Nissan-Datsun Maxima Water Pump: Service and Repair

Filed Under (Nissan) by admin on 09-12-2013

Download When removing water pump assembly, be careful not to get coolant on drive belt. Water pump cannot be disassembled and should be replaced as a unit. After Installing water pump, connect hose and clamp securely, then check for leaks using radiator cap tester. 1.Drain coolant from drain plugs on radiator and both sides of cylinder block. 2.Remove drain plug on cylinder block. 3.Remove right side engine mounting, mounting bracket and nuts. 4.Remove drive belts and idler pulley bracket. 5.Remove chain tensioner cover and water pump cover. 6.Pushing timing chain tensioner sleeve, apply a stopper pin so it does not return. Then remove the chain tensioner assembly. 7.Remove the 3 water pump fixing bolts. Secure a gap between water pump gear and timing chain, by turning crankshaft pulley 2O° backwards. 8.Put M8 bolts to two M8-threaded holes out of 3 water pump fixing bolt holes. 9.Tighten M8 bolts by turning half turn alternately until they reach timing chain rear case.… Read More

1997 Jeep Cherokee Serpentine Belt INSPECTION ADJUSTMENT REMOVAL & INSTALLATION

Filed Under (Jeep) by admin on 31-12-2013

Download 1997 Jeep Cherokee 2WD 4.0L MFI 6cyl | Repair Guides. eep Wagoneer/Command o/Cherokee 1984-1998 Serpentine Belt INSPECTION ADJUSTMENT REMOVAL & INSTALLATION INSPECTION When inspecting serpentine drive belts, small cracks that run across the ribbed surface of the belt from rib to rib are considered normal. If the the cracks are running along the rib (rather across), this is not normal and the belt(s) must be replaced. ADJUSTMENT It is not necessary to adjust belt tension on the 5.2L or 5.9L engines and on the 2.5L and 4.0L engines (without power steering). These engines are equipped with an automatic tensioner. The tensioner maintains correct tension at all times. 2.5L and 4.0L Engines With Power Steering See Figures 1, 2, 3 and 4 If the vehicle is not equipped with power steering, it will be equipped with an idler pulley. If equipped with an idler pulley, refer to and follow the 5.2L/5.9L belt removal and installation procedure.… Read More

You might also likeclose