97 chevy c1500 steering column cover diagram

You search Auto repair manual PDF about 97 chevy c1500 steering column cover diagram, search results will appear below. If search results do not exist, please search by others keyword.

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE

Filed Under (Toyota) by admin on 04-04-2013

Download 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear.… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

2000 Volkswagen Cabrio Ignition Switch: Service and Repair

Filed Under (Volkswagen (VW)) by admin on 02-01-2014

Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More

1989 Chevrolet Corvette Steering Column: Service and Repair

Filed Under (Chevrolet (Chevy)) by admin on 02-12-2013

Download 1989 Chevrolet Corvette V8-350 5.7L Steering Column: Service and Repair Disassembly/Assembly SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined.… Read More

2001 Buick Regal Power Steering Pump Replacement

Filed Under (Buick) by admin on 01-01-2014

Download 2001 Buick Regal V6-3.8L VIN K Vehicle Level Steering and Suspension Steering Power Steering Pump Service and Repair Power Steering Pump Replacement. Removal Procedure 1. Place a drain pan under the vehicle. 2. Remove the accessory drive belt. Refer to Drive Belt Replacement in Engine. 3. Raise and support the vehicle. Refer to Vehicle Lifting . 4. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. 5. Remove the power steering pressure hose from the power steering pump. Refer to Power Steering Pressure Hose Replacement. 6. Remove the power steering return hose from the power steering pump. Refer to Power Steering Return Hose Replacement. 7. Remove the power steering mounting bolts from the power steering pump. 8. Remove the power steering pump. 9. Remove the power steering pump reservoir from the power steering pump. 10. Transfer the power steering pump pulley. Refer to Power Steering Pulley Replacement Installation Procedure 1.… Read More

1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Filed Under (Ford) by admin on 31-12-2013

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

Audi A6 4F APS+ Installation guide

Filed Under (Audi) by admin on 04-01-2014

Download Please disconnect the battery before you are going to start the installation! note: This manual is for experienced people in retrofitting. After Installation the system have to be coded by an Audi dealer: Address 76 (Parkassist) – activation of optical display Address 07 (display front) – chanal 01, current value +4 You should check all components you need before installing: wiring control unit – sensors wiring sensors front 4 suitable sensors in the colour of the car control unit PDC for optical display in MMI buzzer front including button PDC For drilling the wholes into the bumper you will need a 23mm driller („Forstnerbohrer”). For fitting the sensors you will need a hot glue gun as well as sandpaper. Parts as follows has to be removed: Bumper front Cover above the wheel left and right Glove box Entry rail right, frint and back Cover B-post right Back seats Cover trunk in the middle Cover trunk right Cover underneath the steering wheel The control unit for PDC is located behind the trunk cover on the right hand side.… Read More

1992 Ford Taurus V6-182 3.0L Dashboard / Instrument Panel: Service and Repair

Filed Under (Ford) by admin on 11-03-2014

Download NOTE: Removal and installation of the instrument panel is best accomplished by two people. Wiring and Circuit Protection for routing and connection locations. Removal and Installation 1. Position front wheels in the straight ahead position. 2. Disconnect positive battery cable. 3. Remove cluster finish panel, please refer to Body and Frame/Interior Trim/Dash Board/Service and Repair/ See: 4. Disconnect all electrical connections from steering column switches. 5. Remove two bolts and reinforcement from under steering column. 6. Disengage insulator retainer and remove insulator. 7. Remove four nuts and absorber assembly from under steering column. CAUTION: Do not rotate steering column shaft. 8. Disconnect park brake release cable and wiring connector from park brake and ignition switch wiring connector. 9. Remove four nuts retaining steering column to support, disconnect PRNDL cable (column shift) and lower column on front seat. Cover front seat to protect from damage. 10. Install lock cylinder to ensure that steering column shaft does not turn.… Read More

1998 Chevrolet Truck C1500 Repair Information

Filed Under (Chevrolet (Chevy)) by admin on 10-12-2013

Download1988-94 Models See Figures 1 and 2 Remove the steering wheel. 1. Fig. Fig. 1: Installing the lock cylinder. Fig. Fig. 2: Ignition switch Remove the turn signal switch. It is not necessary to completely remove the switch from the column. Pull the switch rearward far enough to slip it over the end of the shaft, but do not pull the harness out of the column. 2. Turn the lock to Run. 3. If necessary, remove the ignition key. 4. If equipped, remove the buzzer switch assembly. 5. Remove the lock retaining screw and remove the lock cylinder. 6. WARNING If the retaining screw is dropped on removal, it may fall into the column, requiring complete disassembly of the column to retrieve the screw. To install: Rotate the key to the stop while holding onto the cylinder. 7. Push the lock all the way in. 8. Install the screw. Tighten the screw to 40 inch lbs.… Read More

Acura B-Series VTEC Engines Street/Strip Camshafts

Filed Under (Acura) by admin on 31-12-2013

Download 1. Make sure the engine is cool and the vehicle is on level ground. Set the parking brake. If you have an original equipment radio with anti-theft protection, make sure to write down the code before disconnecting the battery. After installation, you will need this code to restore radio operation. It is recommended to clean the valve cover, as well as the area surrounding the valve cover, to avoid getting dirt or debris into the engine. Disconnect the negative cable from the battery. 2. Disconnect the PCV hose and ground wire from the valve cover. Using a 10mm socket, remove the four cap nuts holding the spark plug wire cover. Remove the spark plug wire cover and remove the spark plug wire boots from the spark plugs. Using a 5/8″ spark plug socket, remove the spark plugs. This will make turning the engine over in step 5 easier. Using a 10mm socket, remove the remaining eight nuts and washers holding the valve cover, and carefully lift off the valve cover.… Read More

You might also likeclose