". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
Filed Under (Other Manuals) by Doe Namblas on 17-01-2014
Download DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected Refer to Engine Controls Routing Diagram, EVAP Control System Overview . System Description This DTC tests the evaporative emission (EVAP) system for a small leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the vacuum decay rate. At an appropriate time, the control module turns the EVAP canister purge valve ON and the EVAP vent valve ON. This allows the engine to draw a vacuum on the EVAP system. At a calibrated time, or vacuum level, the control module turns the EVAP canister purge valve OFF, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum decay. If the control module detects a leak larger than a calibrated amount, this DTC sets. The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP canister purge and vent valves.… Read More
Download DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected
Filed Under (Other Manuals) by Doe Namblas on 08-04-2014
Download Models: 2002 and Prior Passenger Cars and Light Duty Trucks with Non-Enhanced and Enhanced EVAP Systems. Non-Enhanced EVAP System Diagnostic Procedure 1. Pinch off or plug the EVAP vapor line to seal the EVAP system. 2. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground. 3. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part number. 4. Connect the EEST’s nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter. 5. Turn the nitrogen/smoke valve on the EEST control panel to SMOKE. 6. Use the remote switch to introduce smoke into the EVAP system for 60 seconds. Important: Additional smoke may need to be introduced at 15-second intervals until the leak source has been located. 7. Inspect the entire EVAP system for exiting smoke using the high intensity white light (J 41413-SPT).… Read More
Download Test Guidelines for Use of Essential Tool J 41413-200 Evaporative System Tester
Filed Under (Other Manuals) by Doe Namblas on 01-01-2014
Download 1. Turn OFF the ignition. 2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 3. Disconnect the electrical connector. 4. Remove the EVAP vent valve bracket bolt. 5. Remove the EVAP vent valve from the bracket. 6. Disconnect the vent hose from the EVAP vent valve. 7. Remove the EVAP vent valve. Installation Procedure 1. Install the EVAP vent valve on bracket. 2. Connect the vent hose. Canister vent hose should be routed below the fuel tank fill and vent hoses. Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener.… Read More
Download Evaporative Emission (EVAP) Vent Valve Replacement
Filed Under (Other Manuals) by Doe Namblas on 15-01-2014
Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More
Download Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 31-12-2013
Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More
Download 2004 Chevrolet Chevy K Silverado Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup
Filed Under (Honda) by Doe Namblas on 01-01-2014
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More
Download Honda Civic D-series Racing Intake Manifold Manual Installation Instructions
Filed Under (Honda) by Doe Namblas on 01-01-2014
Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More
Download Honda Civic Racing Intake Manifold Installation Instruction
Filed Under (Acura) by Doe Namblas on 03-01-2014
Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More
Download 1997-2001 Acura Integra Type-R Racing Intake Manifold
Filed Under (Honda) by Doe Namblas on 27-02-2014
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Download 1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions
Filed Under (Honda) by Doe Namblas on 31-12-2013
These 5 adjustments are not active when a ME-RC Remote Control with revision 1.5 or higher is used. They are set using displays under the AGS button on the remote control. Gen Run Signal (input to pin 2 must be 10 to 40 DC volts only while generator is running); this can be the generator hour-meter or a 12vdc pilot/run light
ME-AGS relay timing for 3-Wire Mode. Magnum Energy, Inc. provides this diagram to assist in the installation of the Auto-Generator Start controller. Since the use of this diagram and the conditions or methods of installation, operation and use are beyond the control of Magnum Energy, Inc., we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of the installation, operation and use of this unit.… Read More
Download Honda Generator EM3800SX EM5000SX ME-AGS Wiring Diagram