1995-1996 Honda Civic V 1.4L L4 Part 57-0527 Installation Manual

Download
Honda Civic V 1.4L L4 1995-1996, Honda Civic V 1.4L L4 D14A4 Eng 1997-2001, Honda Civic V 1.6L L4 105BHP 1995-2001 (15.09.10)
1. Unclip and remove air box lid from the vehicle. (Fig. 1) 2. Unbolt & remove the resonator box from the vehicle. (Fig. 2) 3. Disconnect the cam cover breather from the air box base. (Fig. 3) 4. Remove the air temp sensor from the side of the air box. (Fig. 4) 5. Loosen the clip on the throttle neck, unbolt and remove the air box base. (Fig. 5) 6. Remove the 2 short breather hoses from the cam cover outlet and the metal breather hose. (Fig. 6&7) 7. Fit the stepped rubber adaptor onto the throttle housing and firmly tighten using the #44 hose clamp supplied. (Fig. 8) (Note: – This adaptor should be a tight fit) 8. Fit the plastic intake tube into the stepped rubber adaptor & firmly tighten using the #60 hose clamp supplied.… Read More

HONDA CIVIC LX / DX AEM INTAKE SYSTEM INSTALLATION INSTRUCTIONS

Download Installation of AEM® intake system. a. When installing the intake system, do not completely tighten the hose clamps or mounting hardware until instructed to do so. b. Remove the transmission mount bracket nut closest to the front of the car. Install the supplied transmission bracket over the stud and replace the nut. Refer to the picture for correct orientation. Torque the transmission mount bracket nut to 54 N-m (5.5 kgf-m, 40 lbf-ft). (Fig. 9) c. Install the 2.50″ x 2″ hose on to the throttle body with two 2.50″ hose clamps. d. Check to see that the inside of the AEM® intake pipes and air filter are clean and free from any foreign objects and/or obstructions. e. Place the primary intake pipe into the hose on the throttle body. The throttle body end is the end with the IAT sensor hole and breather hose nipple. f. Thread supplied washer and bolt through the intake pipe mounting tab into the factory intake resonator mounting bracket.… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More

2002-2006 Acura RSX Type-S 69-1009 Installation Instructions

Download Acura 2002-06 RSX Type-S L4-2.0L Honda 2002-05 Civic Si L4-2.0L . Part List : A Filtercharger 1 RU-4870 B Hose Clamp, #44 SS 3 08560 C Typhoon Intake Tube 1 27081 D Rubber Cap 1 08282 E Wave washer 1 08277 F 6mm Hex bolt, 16mm L. 1 07812 G Grommet 1 08283 H Hose Clamp, #004 1 21850 I Hose; 5/8″ID, 2-1/4″L, Rubber1 08692 J Silicone Hose black 1 08440 K Hose clamp, #10 mini 2 08411. 1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Loosen and remove the two bolts that secure the engine cover, then remove the engine cover as shown. 3. Using a pair of pliers, depress the hose clamp and slide it back off of the crank case vent on the air cleaner assembly as shown. 4. Using a pair of pliers, depress the hose clamp and remove the air temperature sensor from the stock intake tube as shown.… Read More

1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions

Download
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More

Honda Civic D-series Racing Intake Manifold Manual Installation Instructions

Download
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More

AEM V2 Air Intake System Manual Installation Instructions

Download
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6001
1992-1995 HONDA Civic SI L4-1.6L C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic LX L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1994-1995 HONDA Civic EX L4-1.6L Manual Trans. C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic DX Hatchback L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic DX L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1992-1993 HONDA Civic L4-1.6L Manual Trans. C.A.R.B.E.O. #D-670
1. Preparing Vehicle a. Make sure vehicle is parked on level surface. b. Set parking brake. c. If engine has run in the past two hours, let it cool down. d. Disconnect all negative battery terminals. e. Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle. Support your vehicle using properly rated jack stands before wheel removal or while working under the vehicle. NEVER WORK UNDER A VEHICLE WITHOUT USING JACK STANDS.… Read More

2002-2004 Honda Civic Si Race Supercharger Manual Installation Instructions

Download
TOOLS NEEDED: Most of these tools are available at your local hardware or auto parts store. 10,12,13,14&17mm sockets and wrenches Phillipsand straight blade screw drivers 12mm and 13mm universal “wooble” socket with a 1/4″ drive A good soldering devise and solder.
REMOVAL OF STOCK PARTS: 1. Remove your ECU & Immobilizer: Remove the lower dash trim panel from below the glove box. Remove the ECU assembly. Remove the plastic trim panel from around the steering column and remove the immobilizer assembly from the ignition switch area. Package the ECU, Immobilizer, Main Ignition Key, and completed JR warranty card in the enclosed shipping box with the Hondata label. Ship complete box to Hondata. We suggest using UPS or Fed Ex overnight delivery. 2 . Remove the “IVTEC” plastic cover. Unplug the Air Temperature (T/A) sensor harness from the T/A sensor on the intake rubber hose. The wire colors are green with a yellow stripe and red with a yellow stripe.… Read More

2002 – 2003 Honda Civic Si & Acura RSX Comptech Icebox Cold Air Intake Installation Instructions

Download Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX). Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

Honda Civic Si Acura RSX Icebox Cold Air Intake Manual Installation Instructions

Download
Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX).
Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More