89 chevy steering column wiring diagram
You search Auto repair manual PDF about 89 chevy steering column wiring diagram
, search results will appear below. If search results do not exist, please search by others keyword.
Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013
Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More
Filed Under (Toyota) by admin on 04-04-2013
Download 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear.… Read More
Filed Under (Volkswagen (VW)) by admin on 02-01-2014
Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More
Filed Under (Chevrolet (Chevy)) by admin on 02-12-2013
Download 1989 Chevrolet Corvette V8-350 5.7L Steering Column: Service and Repair Disassembly/Assembly SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined.… Read More
Filed Under (Buick) by admin on 01-01-2014
Download 2001 Buick Regal V6-3.8L VIN K Vehicle Level Steering and Suspension Steering Power Steering Pump Service and Repair Power Steering Pump Replacement. Removal Procedure 1. Place a drain pan under the vehicle. 2. Remove the accessory drive belt. Refer to Drive Belt Replacement in Engine. 3. Raise and support the vehicle. Refer to Vehicle Lifting . 4. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. 5. Remove the power steering pressure hose from the power steering pump. Refer to Power Steering Pressure Hose Replacement. 6. Remove the power steering return hose from the power steering pump. Refer to Power Steering Return Hose Replacement. 7. Remove the power steering mounting bolts from the power steering pump. 8. Remove the power steering pump. 9. Remove the power steering pump reservoir from the power steering pump. 10. Transfer the power steering pump pulley. Refer to Power Steering Pulley Replacement Installation Procedure 1.… Read More
Filed Under (Ford) by admin on 11-03-2014
Download NOTE: Removal and installation of the instrument panel is best accomplished by two people. Wiring and Circuit Protection for routing and connection locations. Removal and Installation 1. Position front wheels in the straight ahead position. 2. Disconnect positive battery cable. 3. Remove cluster finish panel, please refer to Body and Frame/Interior Trim/Dash Board/Service and Repair/ See: 4. Disconnect all electrical connections from steering column switches. 5. Remove two bolts and reinforcement from under steering column. 6. Disengage insulator retainer and remove insulator. 7. Remove four nuts and absorber assembly from under steering column. CAUTION: Do not rotate steering column shaft. 8. Disconnect park brake release cable and wiring connector from park brake and ignition switch wiring connector. 9. Remove four nuts retaining steering column to support, disconnect PRNDL cable (column shift) and lower column on front seat. Cover front seat to protect from damage. 10. Install lock cylinder to ensure that steering column shaft does not turn.… Read More
Filed Under (Ford) by admin on 31-12-2013
Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More
Filed Under (Honda) by admin on 27-02-2014
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Filed Under (Ford) by admin on 01-01-2014
Download 1. SAFETY REQUIREMENTS STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation. 1. Always wear safety glasses for eye protection. 2. Place ignition switch in the OFF position. 3. Always apply the parking brake when working on a vehicle. 4. Block the front and rear tire surface to prevent unexpected vehicle movement. 5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. 6. Do not smoke or use flammable items near or around the fuel system. 7. Use chemicals and cleaners in well-ventilated areas. 8. Batteries produce explosive gases, which can cause personal injury.… Read More
Filed Under (Other Manuals) by admin on 07-02-2014
Download Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville. Condition Some customers may comment on a steering vibration, shudder or moan noise when steering during parking maneuvers on dry pavement. Correction Install a new power steering pressure (inlet) hose assembly on the following vehicles: Install a new power steering pressure (inlet) and return (outlet) hose assembly on the following vehicles: Diagnosis Important: In diagnosing the above listed vehicles, do not overlook other obvious repairs prior to replacing the hose(s). 1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions.… Read More