2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More

2010 Hyundai Genesis Coupe Short Shifter Manual Installation Instructions

Download
Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the short shifter on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working. Please read this installation manual completely before installing the short shifter. Make sure to let the car cool down before you do the install as you will be working on and around the exhaust line.
INSTALLATION INSTRUCTIONS: 1. Working inside the car, unsnap the shift boot from the shift knob and remove the shift knob by rotating it counter clockwise. Put it aside in a safe place for re-install later. 2. With your fingers inside the shift boot, pull the shifter console up. 3. If you have heated seats, unplug the connector from the console.… Read More

Audi A4 B6/8E 5 Speed Short Shifter Installation Manual

Download A. Required Tools Safety Glasses (! See Warnings!) Circlip Pliers Hose Clamp Cutter Razor Blade Ratchet 3/8 or 1/4 Inch Drive Sockets Metric 3/8 or 1/4 Drive (7mm & 10mm) Extension Medium Length 3/8 or 1/4 Inch Drive 6mm Allen Key 6mm Allen Socket 2.5mm Allen key (Included in kit) T-25 Torx Driver 10mm Wrench 24mm or Adjustable Wrench. Step 1: Removal of console cover plate and shift knob. To remove the cover plate, open the ashtray and pull up on the front of the cover. Do the same for the rear of the cover by lifting from within the shift boot at the rear side. To remove the shift knob you must cut the clamp holding the shift knob we have included a new one in the kit. (! Safety glasses are required while cutting the hose clamp!) Once you have removed the clamp, pull up on the shift knob to remove it.… Read More

1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

2001 Honda Prelude Timing Belt Removal and Installation

Download 2001 Honda Prelude L4-2157cc 2.2L DOHC (VTEC) MFI Vehicle Level Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Removal and Installation. REMOVAL NOTE: * Turn the crankshaft pulley so the No. 1 piston is at Top Dead Center (TDC) before removing the belt. * Inspect the water pump after removing the timing belt. * Replace the timing belt and timing balancer belt at 105,000 miles (168,000 km) according to the maintenance schedule (normal conditions/severe conditions). If the vehicle is regularly driven in one or more of the following conditions, replace the timing belt and timing balancer belt at 60,000 miles (U.S.A.) 100,000 km (Canada). * In very high temperatures (over 110°F, 43°C). * In very low temperatures (under -20°F, -29°C). 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the radio’s preset buttons. 2. Disconnect the battery negative terminal first, then the positive terminal.… Read More

2002 Acura RSX-Type S Short Throw Shift Adapter Installation Manual

Download 1. Pull down chrome collar and carefully unscrew and remove the stock shift knob. 2. Remove the front console cover. Pull up from the front to unclip the clips and remove from the vehicle. 3. Remove the 2 screws securing the front part of the console. Remove any additional screws that may be holding the center part of the console in place, this may vary by year and model. Lift the 2 tabs shown to the right over the center section of the console so that they rest on the outside of the console assembly. 4. Spread the front sections of the console away from the center console to unclip the 2 clips securing them in place. This may be simplified by pushing from the inside with a hard object next to the clip. 5. Pull the center console to the rear of the vehicle ensuring the sides of the front section of the console remain apart and out of the way.… Read More

1980-1992 Ford AOD Shift Improver Kit Installation Instructions

Download IMPORTANT: We recommend that you read through the instructions completely before beginning the installation so you can familiarize yourself with the installation procedure and tools required. Check the tool list at the end of these instructions for the tools required to install your B&M AOD Shift Improver Kit. Installation of the B&M AOD Shift Improver Kit can be accomplished by anyone with minimum mechanical experience. It is however, important to closely follow the instructions. Read each step carefully before proceeding, if you do not understand, go back and read the step again. NOTICE: The B&M AOD Shift Improver Kit is not a cure-all for an ailing transmission. If your transmission is slipping, chatters or is in poor general shape, the installation of this Shift Improver Kit may worsen the condition. However on a properly operating transmission in average condition, the B&M AOD Shift Improver Kit will provide the kind of transmission performance you are looking for.… Read More

1997-2003 Honda CRV Signal Mirror Manual Installation Instructions

Download
Door Panel & Mirror Housing Removal 2002-2003 Honda CRV:1. Open door and lower window. 2. Remove plastic cover from corner of door. 3. Pop-out and remove plastic inserts. 4. Remove door handle plastic cover. 5. Unscrew the (2) screws revealed by the removal of the door handle cover. 6. Pry out door handle as shown. Disengage latch behind door handle and remove door handle. 7. Remove the (2) screws beneath armrest. 8. Lift up and pull door panel out slightly as shown. Disconnect any wiring connection behind door panel. Remove door panel from door. 9. Unscrew the (3) nuts holding the mirror housing to the door. Remove mirror housing from door.
Door Panel & Mirror Housing Removal 1997-2001 Honda CRV : 1. Open door and lower window. 2. Remove screw and plastic grommet on inside corner of door. 3. Remove plastic cover from corner of door. 4. Disconnect the mirror wire harness.… Read More

1996-1999 Audi A4/1998 VW Passat Short Shifter Installation Instructions

Download The following parts are included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: – 13mm socket and ratchet – 10mm socket and ratchet – socket wobble (universal joint) attachment – socket extension – snap ring / circlip pliers – 6mm allen socket head bit – flexible plunger-type four-claw retriever – torx T-25 driver (only for 2000 A4, S4 and A6 Biturbo) Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console. Step 3 – Remove black plastic collar Step 4 – Remove circlip Use circlip pliers to remove circlip from shift lever.… Read More