1994 Mercury Cougar XR7 INTERIOR FUSE PANEL IDENTIFICATION

Download 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. INTERIOR FUSE PANEL IDENTIFICATION (1994-95 MODELS) On all models, the fuse panel is located under the instrument panel, left of the steering column. Fuse & Circuit Breaker Identification 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module 10 – 10 Amp OBD-II Test Connector 11 – Not Used 12 – 5 Amp Illumination Of: Cluster, Phone Switch, Rear Defrost Switch, A/C Switch (Manual), PRNDL Indicator, Ashtray, EATC, Clock, Radio 13 – 20 Amp Cigarette Lighter, Flash-To-Pass 14 – 15 Amp Speed Control Module, ABS Module, BrakeShift Interlock, High Mount Brakelight, Brakelights, Flashers 15 – 5 Amp Cluster (Gauges), Cluster (ABS & Airbag Warning), Warning Chime, Autolight Sensor 16 – 10 Amp Integrated Module, Sport Voltmeter, Speed Control, Remote Keyless Entry, Anti-Theft, Power Window/Door Lock Switch Illumination, Radio, CD Changer, Power Antenna, Clock 17 – 30 Amp Wiper/Washer System 18 – 20 Amp Power Door Locks, Decklid Release, Fuel Door Release, Power Seats, Power Lumbar, Booster 19 – 20 Amp Power Window Motors, Moon Roof Motor UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron.… Read More

1998 – 2001 Ford Explorer 4WD Ford Ranger Explorer Sport Trac / Edge Mountaineer 4WD Torsion bar key front leveling kit

Download Part # 22907 1998 – 2001 Ford Explorer 4WD 1998 – 2007 Ford Ranger / Explorer Sport Trac Edge / Mountaineer 4WD Torsion bar key front leveling kit Part# Description Qty. 22907-01 Torsion bar keys 2 22907INST Instruction manual (customer copy) 1 22907INST Instruction manual (installer copy) 1 WARNINGDECAL Warning decal 1 MIRRORHANGER Rear view mirror hanger 1. Important customer information: Tuff Country EZ-Ride Suspension highly recommends that a qualified and/or certified mechanic performs this installation. If you desire to return your vehicle to stock, it is the customers responsibility to save all stock hardware. This vehicles reaction and handling characteristics may differ from standard cars and/or trucks. Modifications to improve and/or enhance off road performance may raise the intended center of gravity. Extreme caution must be utilized when encountering driving conditions which may cause vehicle imbalance or loss of control. DRIVE SAFELY! Avoid abrupt maneuvers, such as sudden sharp turns which could cause a roll over, resulting in serious injury or death.… Read More

2008-2011 FORD Focus PART 99-5816 INSTALLATION INSTRUCTIONS

Download KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision • Painted To Match Factory Dash • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket • G) (2) Top Clips and (4) Middle Radio Housing Clips Wiring & Antenna Connections (sold seperately) XSVI-5520-NAV – Ford Interface AFSI-02 – if equipped w/ sync 70-5522 – Ford Sub Harness KIT COMPONENTS A TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver • Socket Set • Cutting Tool. 95-5816 DASH DISASSEMBLY. to prevent an accidental short cir- cuit. 1 Unclip and remove the trim panel surrounding the shifter and including the cup holders. (Figure A) Remove (2) 9/32″ screws facing up above the gauge cluster then unclip and remove the trim panel surrounding the gauge cluster.… Read More

Ford Street Rod Pickup Bed Installation Instructions

Download REQUIRED TOOLS Flat work surface, floor or bench Electric or battery drill Drill bits – 1/8 -5/16 – 11/32 – 17/32 Mig welder (optional) Body grinder (optional) Wrenches – 9/16″ – 1/2″ – 7/16″ 3/16 Allen wrench Nutsert installation tool – available from Pro’s Pick or industrial hardware supply Tape measure, Felt tip marker, Pencil MBCHYCDQV42H STEP 1 UNPACKING Check the contents to make sure that it’s all here! Description Qty Front panel 1 Left bedside 1 Right bedside 1 Cross members 4 may be various sizes *42-47 only has 3 Rear cross member 1 Rear cross member hardware kit 1 As with most things in life there is more than one way to skin a cat. When Henry produced your truck it was meant to haul hay & pigs. They weren’t too fussy about the way things fit. Today we expect things to fit like the new vehicles. If you take a side view of most of the Ford trucks of this era they look like their back is broken and if you look at a 40 from the side, the hood looks like it’s going uphill.… Read More

1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS

Download FORD: 1995-1997 EXPLORER 2. Connect the New Generation Star (NGS) Tester ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL.… Read More

Honda ST 1300 Front Panel Kit Installation Instructions

Download Introduction: Made in USA This easy to install, high quality, Powerlet™ kit provides a convenient way to access the battery on Honda ST1300 motorcycles. The operator can supply power to the battery (i.e. battery charger), draw power from the battery (i.e. cell phone), or monitor the state of charge on the battery using the Powerlet socket. Parts List: • 1 – Wiring harness w/ 15A fuse • 1 – Powerlet socket • Ty-wrap(s) Please read all of the instructions carefully before attempting the installation of this product. Quick Start Instruction: STEP #1 Remove the seat & necessary panels. STEP #2 Drill the hole for the socket, do not install. STEP #3 Attach the socket to the panel. STEP #4 Install & route harness. STEP #5 Attach the wires to the socket and test. STEP #6 Reinstall panels & seat. Detailed Instruction: STEP #1 – Expose the battery by removing the seat & side panels on the right side of the bike.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Download FORD Edge 2007-2009 / Expedition 2007-2009 Explorer 2006-2009 / Explorer Sport Trac 2006-2009 F-150 2004-2008 / F Series 2005-2008 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2009 Mustang 2005-2009 / Super Duty 2008-2009 Taurus 2008-2009 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2009 Sable 2008-2009 LINCOLN Mark LT 2005-2009 Factory Navigation Only: MKX 2007-2009 / Navigator 2007-2009. DASH DISASSEMBLY A B C D E FORD MUSTANG 2005-2009 Remove the small rectangular shifter lever trim panel if equipped . (Figure A) 2 Remove (4) 9/32″screws from the radio to remove. (Figure E) 7 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (includingcup holders). (Figure B) 3 Unclip and remove panel. (Figure B) 4 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More