2009 hyundai accent timing marks

You search Auto repair manual PDF about 2009 hyundai accent timing marks, search results will appear below. If search results do not exist, please search by others keyword.

2001 Hyundai Accent Difficulty filling the gas tank. The pump keeps clicking off.

Filed Under (Hyundai) by admin on 02-04-2014

Download 2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Customer Concern: Difficulty filling the gas tank. The pump keeps clicking off. Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted.… Read More

2000 Plymouth Breeze TIMING BELT Removal Inspection Installation

Filed Under (Plymouth) by admin on 10-02-2014

Download 1. Raise vehicle on hoist and remove right front wheel. Remove right inner splash panel. Remove accessory drive belts. Remove crankshaft vibration damper. 2. Remove generator drive belt idler pulley. Remove lower timing belt cover. 3. Remove right engine support assembly vertical bolts from bottom of frame rail (timing belt end of engine). 4. Lower vehicle. Remove upper timing belt cover. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine mount assembly to engine bracket. 5. Move A/C drier aside. Remove coolant reservoir tank. Remove right engine mount. Remove 3 bolts attaching engine mount bracket to engine block. 6. Rotate crankshaft clockwise to align timing marks on camshafts and oil pump housing. See Fig. 1 . 7. On models equipped with hydraulic tensioner, remove hydraulic tensioner bolts and remove tensioner. Place hydraulic tensioner in vise, and SLOWLY compress tensioner plunger. Align the holes in the tensioner body and plunger, and insert a pin through the body and plunger to lock the plunger in place.… Read More

2001 Daewoo Leganza SE TIMING BELT REMOVAL and INSTALLATION

Filed Under (Daewoo) by admin on 01-01-2014

Download 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).… Read More

NISSAN MAXIMA / ALTIMA / QUEST; BUZZING / WHINING NOISE FROM TIMING CHAIN AREA

Filed Under (Nissan) by admin on 02-01-2014

Download 2004-2008 Maxima (A34) 2004-2006 Altima (L31) with VQ35 engine ONLY 2004-2009 Quest (V42) IF YOU CONFIRM: There is a high frequency buzzing / whining noise coming from the secondary timing chain system. • The noise should increase in frequency with engine speed (RPM). • If the noise does not increase with engine speed, the timing chain system may not be the cause. Refer to the appropriate section of the Electronic Service Manual (ESM) for further diagnosis. ACTION: 1. Replace both secondary timing chains and both secondary timing chain tensioner “shoes” with the ones from the PARTS INFORMATION section of this bulletin (on Page 2). 2. Change the engine oil and filter. 3. For repair procedure, refer to the SERVICE PROCEDURE section of this bulletin (starting on Page 3). SERVICE PROCEDURE Write down all radio station presets. Presets 1 2 3 4 5 6 A B C 2. Disconnect both battery cables, negative cable first.… Read More

2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Filed Under (Infiniti) by admin on 16-12-2013

Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More

1995 Isuzu Trooper LS TIMING BELT REMOVAL and INSTALLATION

Filed Under (Isuzu) by admin on 01-01-2014

Download Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler hose from timing cover. Remove timing belt cover. Align all timing marks prior to belt removal. See Fig. 1 – Fig. 4 . Remove belt tensioner pusher and timing belt. Installation 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt.… Read More

Ford COMP Cams Timing Set Installation Instructions

Filed Under (Ford) by admin on 28-01-2014

Download
Engine Application Ford V6, 144-200; Ford V6, 171 (2600-2800cc); Ford V8, 255, 289, 302 & Boss 302, 1965-1988; Ford V8, 289-351W & Boss 302, pre 1972; Ford V8, 302-351W, 1972 & up; Ford V8, 352-428, 1964-1974; Ford V8, 351C, 351M, 400M, 1970-1982; Ford V8, 429-460, 1968-1971; Ford V8, 429-460, 1972-1987; Ford V8, 429-460 w/nine keyway crank gear; Ford V8, 351W, 351W H.O., 1969-¹84; Ford V8, 5.0L 302 H.O., 1980-March 21, 1984; Ford V8, 5.0L 302, 351W, March 22, 1984-1992.
Tools and supplies needed: 1. Basic hand tools as required for your particular camshaft and balancer bolts 2. Torque wrench 3. Pro Cam Lube (part #153 or #154) or suitable replacement 4. Camshaft Degree Kit (part #4796 including degree video) 5. Crankshaft Socket (part #4798 for Ford 302-351W, 429-460) 6. Thread locking compound 7. Engine repair manual for your particular engine.
The following instructions begin after the timing cover and old timing set have been removed.… Read More

2000 Cadillac Catera TIMING BELT REPLACEMENT

Filed Under (Cadillac) by admin on 28-11-2013

Download 2000 Cadillac Catera V6-3.0L VIN R Timing Belt: Service and Repair Timing Belt Replacement. Removal Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection and maintenance may result in a broken timing belt and cause severe engine damage. 1.Inspect the cold start counter (also called a heavy duty register) with a scan tool. If there are any cold starts (below -28° C or -20° F) visually inspect the timing belt for cracks. It cracks are noted, do not reuse the belt. Replace the belt and clear the cold start counter. If the belt is okay, and is reused, do not clear the cold start counter. 2.Remove the intake air resonator. Refer to Intake Air Resonator Replacement in Powertrain Management. 3.Remove the intake plenum. Refer to Intake Plenum Replacement. 4.Remove the timing belt cover. Refer to Timing Belt Cover Replacement.… Read More

1990 Ford Ranger Timing Belt Installation Instructions

Filed Under (Ford) by admin on 03-03-2014

Download FORD’ ’2.0L & 2.3L 4-Cylinder – Gasoline – 1974-94 Except Probe REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure “O” mark on crankshaft pulley aligns with “O” mark on outer timing belt cover. 2. Looking through plug hole of outer timing belt cover, ensure camshaft sprocket timing mark aligns with cover pointer. See Fig. 1 . 3. Remove fan guard, cooling shroud, cooling fan and fan shroud. Remove drive belt, water pump pulley and automatic belt tensioner. Discharge A/C system (if equipped) using approved refrigerant recovery equipment. Remove A/C compressor mounting bracket with power steering pump attached, and position aside. Drain cooling system. Remove upper radiator hose. Remove thermostat housing and gasket. 4. Remove retaining bolt and crankshaft pulley. Remove hub assembly retaining bolt from crankshaft. Remove outer timing belt cover. Ensure camshaft sprocket timing mark aligns with cover pointer.… Read More

2002 HONDA ACCORD – Timing Belt and Balancer Belt Installation

Filed Under (Honda) by admin on 31-12-2013

Download Special Tools Required ?Holder Handle 07JAB-001020A ?Holder Attachment, 50 mm, Offset 07MAB-PY3010A ?Socket, 19 mm 07JAA-001020A or a commercially available 19 mm socket NOTE: ?If you are installing the timing belt and the balancer belt, go to step 1. ?If you are installing only the balancer belt, go to step 7. 1. Remove and clean the balancer belt drive pulley. 2. Clean the timing belt pulleys, and the upper and lower timing cover. 3. Set the crankshaft to TDC. Align the dimple (A) on the tooth of the timing belt drive pulley with the pointer (B) on the oil pump. 4. Clean the camshaft pulley and set it to TDC. 5. Install the timing belt in a counterclockwise sequence, starting with the drive pulley. -1 The ”UP” mark (A) on the camshaft pulley should be at the top. -2 Align the TDC grooves (B) on the pulley with the top edge of the head.… Read More

You might also likeclose