2008 chevy colorado vent valve solenoid location

You search Auto repair manual PDF about 2008 chevy colorado vent valve solenoid location, search results will appear below. If search results do not exist, please search by others keyword.

Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit

Filed Under (Other Manuals) by admin on 15-01-2014

Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More

Evaporative Emission (EVAP) Vent Valve Replacement

Filed Under (Other Manuals) by admin on 01-01-2014

Download 1. Turn OFF the ignition. 2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 3. Disconnect the electrical connector. 4. Remove the EVAP vent valve bracket bolt. 5. Remove the EVAP vent valve from the bracket. 6. Disconnect the vent hose from the EVAP vent valve. 7. Remove the EVAP vent valve. Installation Procedure 1. Install the EVAP vent valve on bracket. 2. Connect the vent hose. Canister vent hose should be routed below the fuel tank fill and vent hoses. Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener.… Read More

2004 Chevrolet Chevy K Silverado Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More

2008 Ford Super Duty F-Series Accessories List DESCRIPTION

Filed Under (Ford) by admin on 18-03-2014

Download “Mobile-ease™” Hands Free System Connector Wiring Harness Required for Installation of “Mobile-ease™” Hands Free System 3W4Z-14A411-AA 2005-2008 Hands Free System Requires Connector Harness 14A411 for Installation3W4Z-19G399-AA2005-2008 Bed Hooks, Retractable Stainless Steel XC3Z-99000A64-AA 2000-2008 Black E-Coat XC3Z-99000A64-BA 2000-2008 Bed Mats Long Bed, Styleside, With Ford Logo F81Z-99112A15-AA 1999-2008 Short Bed, Styleside, With Ford Logo F81Z-99112A15-BA 1999-2008 Bed Rail Caps, Diamond Plate Short Bed, With Stake Pocket Holes F81Z-99291A40-CAA 1999-2008 Long Bed, With Stake Pocket Holes F81Z-99291A40-DAA 1999-2008 Bedliner/Bedmat Tailgate Cover F75Z-99000A38-AA 1999-2008 Bedliners** With Ford Logo For Styleside 8.0′ Bed F81Z-9900038-AA 1999-2008 For Styleside 6.5′ Bed F81Z-9900038-BA 1999-2008 Bug Shield Low Profile Smoke-Color (Single-Pack) 8C3Z-16C900-A 2008 Smoke-Color (Bulk Pack of 10) 8C3Z-16C900-B 2008 Smoke-Color (Bulk Pack of 25) 8C3Z-16C900-C 2008 Mini Chrome-Color (Single-Pack) 8C3Z-16C900-D 2008 Chrome-Color (Bulk Pack of 10) 8C3Z-16C900-E 2008 Chrome-Color (Bulk Pack of 25) 8C3Z-16C900-F 2008. Deflectors, Side Window Crew Cab 4-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-CA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-HA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-JA 1999-2008 Regular Cab 2-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-AA 1999-2008 2-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-BA 1999-2008 2-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-CA 1999-2008 Super Cab 4-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-BA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-EA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-FA 1999-2008 Floor Mats, All Weather Molded Vinyl Front & Rear, 3-Piece Set, Front With Vehicle Logo Super Cab, Ebony 8C3Z-2613300-B 2008 Crew Cab, Ebony 6C3Z-2813300-A 2002-2008 Front Pair, With Vehicle Logo Reg.… Read More

2003 Cadillac Escalade Code C0660 will reset.

Filed Under (Cadillac) by admin on 20-12-2013

Download Vehicle Application: 2003 Cadillac Escalade 5.3L, Vin T, USA/Canada 2005 Chevrolet Suburban 1500 LS 5.3L, GAS, Vin T 2003 Cadillac Escalade EXT 6.0L 2005 GMC Yukon XL 1500 Slt 5.3L, FLEX, Vin Z 2005 Chevrolet Suburban 1500 LS 5.3L, FLEX, Vin Z Customer Concern: Code C0660 will reset. Tests/Procedures: 1. Check the RTD fuse located in the underhood fuse block. 2. Check for Battery Voltage (B+) on the Orange wire at the automatic level control air compressor pin F. 3. If less than B+ at pin F, check for a wiring and connection problem between the air compressor and the underhood fuse block. 4. Disconnect the compressor leveling module connector and check the resistance from the positive battery voltage circuit of the exhaust solenoid valve and the control circuit of the exhaust solenoid valve. Should be 30-90 ohms. 5. Check for B+ on the Dark Blue wire pin B at the air compressor with the exhaust solenoid commanded off.… Read More

2005 Dodge Truck Dakota TRANSMISSION SOLENOID/TRS

Filed Under (Dodge) by admin on 21-01-2014

Download The transmission solenoid/TRS assembly is internal to the transmission and mounted on the valve body assembly. The assembly consists of six solenoids that control hydraulic pressure to the six friction elements (transmission clutches), and the torque converter clutch. The pressure control solenoid is located on the side of the solenoid/TRS assembly. The solenoid/TRS assembly also contains five pressure switches that feed information to the TCM. OPERATION SOLENOIDS Solenoids are used to control the L/R, 2C, 4C, OD, and UD friction elements. The reverse clutch is controlled by line pressure and the position of the manual valve in the valve body. All the solenoids are contained within the Solenoid and Pressure Switch Assembly. The solenoid and pressure switch assembly contains one additional solenoid, Multi-Select (MS), which serves primarily to provide 2nd and 3rd gear limp-in operation. The solenoids receive electrical power from the Transmission Control Relay through a single wire. The TCM energizes or operates the solenoids individually by grounding the return wire of the solenoid as necessary.… Read More

Ford C-4 Trans-Brake Reversed Pattern Manual Installation Instructions

Filed Under (Ford) by admin on 04-01-2014

Download Recommended Options: 72803 6 Clutch Drum Assembly 72203 Direct Clutch Kit (6) Blue List of Enclosed Parts (1) Valve Body Assembly (1) Billet Intermediate Servo Cover (1) Solenoid Mounting Block (1) Solenoid Mounting Clip (1) 5/16-18 X 5/8 Whiz Lock Bolt (Solenoid Mounting) (1) Brake Valve (1) Brake Valve Spring (1) Solenoid and Pin Note: Prior to beginning installation of this Trans-Brake kit it is recommended that you be knowledgeable in the assembly of your transmission. If necessary consult a manual or seek the advice of a transmission shop. The transmission must be properly rebuilt for racing before installation of this Trans-Brake. 1.Remove the transmission pan and existing valve body. 2.Ford designates its intermediate servos by letters which appear on the servo cover (A, H, R, K, O, etc.). Note this designation, if your transmission is equipped with a “K” or “R” servo it must be replaced with a servo which has a larger diameter that seals in the bore of the case rather than the bore in the cover.… Read More

1984-1995 Honda Civic/CRX Positive Crankcase Ventilation (PCV) System

Filed Under (Honda) by admin on 31-12-2013

Download SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe.… Read More

1994 Chevy Truck C 1500 Ignition – Timing Connector Location Change

Filed Under (Chevrolet (Chevy)) by admin on 07-02-2014

Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More

1997-2001 Acura Integra Type-R Racing Intake Manifold

Filed Under (Acura) by admin on 03-01-2014

Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More

You might also likeclose