Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit

Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More

1997-2001 Acura Integra Type-R Racing Intake Manifold

Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More

2005 Chevrolet Colorado Pickup Canyon, Colorado (VIN S/T) Service Manual

Download Subject: SES Light Due to DTCs P0105, P0106, and/or P0506 – Clean Throttle Body Models: 2004-2007 Buick Rainier 2002-2007 Chevrolet TrailBlazer 2004-2007 Chevrolet Colorado 2002-2007 GMC Envoy 2004-2007 GMC Canyon 2002-2004 Oldsmobile Bravada 2006-2007 HUMMER H3 2005-2007 Saab 9-7X with any of the following engines: 2.8L (VIN 8 – RPO LK5) 2.9L (VIN 9 – RPO LLV) 3.5L (VIN 6 – RPO L52) 3.7L (VIN E – RPO LLR) 4.2L (VIN S – RPO LL8) The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition/Concern: On rare occasions, a SES light may be experienced due to DTCs P0105, P0106, and/or P0506. There may or may not be an idle complaint accompanying the SES light. This may be due to excessive carbon build up in the throttle body. Recommendation/Instructions: If the SI diagnostics do not isolate a cause for this concern, clean the throttle body bore and plate for evaluation.… Read More

1994 Chevy Truck C 1500 Ignition – Timing Connector Location Change

Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More

1984-1995 Honda Civic/CRX Positive Crankcase Ventilation (PCV) System

Download SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe.… Read More

1994-2001 Acura Integra Racing Intake Manifold

Download 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt (2) lower intake manifold bolts that secure the manifold to the engine block. This bracket will still be used to accommodate the heater bypass pipe. Next, unbolt the manifold from the cylinder head. Remove the intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors. 4. Remove the intake air bypass (IAB) vacuum tank, check valve, and control solenoid valve.… Read More

Honda / Acura SIRIUS Interface HON-SC1 INSTALLATION INSTRUCTIONS

Download Compatibility The HON-SC1 is designed to be compatible with select Honda/Acura vehicles. Please consult table for compatibility listing. Compatible Headunit Types: • CD only Headunits* • CD + Cassette Headunits* • 6-CD changer Headunits* • Touch Screen Monitor Headunits • Non-Touch Screen Monitor Headunits * Note: Radio must have a “SAT” or “XM” button to access SIRIUS audio modes. In addition, the HON-SC1 is compatible with most additional factory audio accessories that might be included, such as: • Rear Seat Audio Control Center • Rear Seat Entertainment (DVD/Monitor) System • Heads up display (HUD) • Steering wheel controls Note: Kit not recommended for vehicles with Technology Package (Please see Acura’s website for details). The HON-SC1 is not compatible with the factory satellite radio antenna that might be installed in the vehicle. For best operation you must install a SIRIUS compatible antenna as supplied with the compatible SIRIUS Satellite Radio tuner.… Read More

Audi TT A.W.E. Tuning DV1 Diverter Valve

Download 1.8T Audi TT, VW Golf/Jetta/New Beetle. Step 1: Here’s an overview picture of the transverse 1.8T engine found in the Audi TT, VW Golf/Jetta/New Beetle 1.8T. The 225hp TT engine looks a little different, but the install of the A.W.E. Tuning valve is the same procedure. For picture clarity, and ease of install, the decorative engine cover has been removed. Removing the cover is easily done by twisting the “+” shaped fasteners on the cover 90 degrees. They’ll pop up when free, allowing you to grab the cover and lift it up and out of the engine bay. (New Beetle requires removing 2 10mm nuts hidden under trim caps, and then sliding forward and out) We’ve also removed the PCV damper in the following pictures for clarity. You won’t need to remove this item to install the valve. Installation instructions for A.W.E. Tuning DV1 Diverter Valve For 1.8T Audi TT, VW Golf/Jetta/New Beetle Thank you for purchasing the A.W.E.… Read More