2001-2006 Acura MDX Signal Mirror Installation Instructions

Download For 1999-2004 Honda Odyssey, 2003-2006, 2007* & 2008* Honda Pilot, and 2001-2006 Acura MDX. Door Panel Removal 1. Open the driver side door and lower the window. 2. Remove the tweeter pod by pulling it away from the door starting at the top section. 3. Remove speaker grill using a small screwdriver to pull up the side under the armrest using the small screwdriver indention. Once you pull up the back slide the grill backwards to release the front. 4. Remove 3 brass speaker screws to remove speaker and disconnect wiring. Remove 3 black screws holding door panel. 5. Open screw cover in door handle using small screwdriver to lift the rear of the cover and then remove screw. 6. Push casing forward until the rear edge can be pulled away from door (you may want to use lever as though you are opening door) and use a small screwdriver to release handle rod.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

2008 ACURA MDX BODY SIDE MOLDING INSTALLATION INSTRUCTIONS

Download 1. Attach the masking tape to the upper part of the front door along the character line. Using a felt-tip pen, mark the masking tape 500 mm from the door edge. 2. Measure down from the masking tape and mark the door at the two points shown. Attach another piece of masking tape above the marks. 3. On the back of the left front body side molding, remove one inch of the adhesive backing from the four ends and tape them to the front of the body side molding. Remove the remaining adhesive backings. 4. Using one alcohol pad, clean the area where the side molding will attach. 5. Position the molding on the door and align it with the masking tape. Remove the masking tape. NOTE: If door edge guards are installed, match the rear edge of the left front body side molding with the door edge guard. 6.… Read More

2007-2008 Acura TL Type S CABIN AIR FILTER IDENTIFICATION

Download Acura CSX, CSX Type S, MDX, RDX, RL, TL, TL Type S, TSX; Honda Accord, Accord Hybrid, Civic, Civic Hybrid, CR-V, Odyssey, Pilot, Ridgeline OE: 80292-SEC-A01 Fits: 2007-on Acura CSX, CSX Type S, MDX, RDX, Honda CR-V 2005-on Acura RL, Honda Odyssey 2004-on Acura TL, TSX 2007-08 Acura TL Type S 2003-on Honda Accord 2005-07 Honda Accord Hybrid 2006-on Honda Civic, Ridgeline 2 006-09 Honda Civic Hybrid 2009-on Honda Pilot. 1. Open passenger side door. 2. Open glove compartment. 3. Detach damper rod from glove compartment. 4. Push in on left and right sides of glove compartment to release glove compartment. If equipped with tabs: a. Close glove compartment part way to relieve pressure on tabs. b. Push in tabs on outside of glove compartment to release glove compartment. c. Remove tabs. 5. Remove screws on left and right sides (if equipped) while holding glove compartment. 6. Flip down glove compartment.… Read More

Honda / Acura SIRIUS Interface HON-SC1 INSTALLATION INSTRUCTIONS

Download Compatibility The HON-SC1 is designed to be compatible with select Honda/Acura vehicles. Please consult table for compatibility listing. Compatible Headunit Types: • CD only Headunits* • CD + Cassette Headunits* • 6-CD changer Headunits* • Touch Screen Monitor Headunits • Non-Touch Screen Monitor Headunits * Note: Radio must have a “SAT” or “XM” button to access SIRIUS audio modes. In addition, the HON-SC1 is compatible with most additional factory audio accessories that might be included, such as: • Rear Seat Audio Control Center • Rear Seat Entertainment (DVD/Monitor) System • Heads up display (HUD) • Steering wheel controls Note: Kit not recommended for vehicles with Technology Package (Please see Acura’s website for details). The HON-SC1 is not compatible with the factory satellite radio antenna that might be installed in the vehicle. For best operation you must install a SIRIUS compatible antenna as supplied with the compatible SIRIUS Satellite Radio tuner.… Read More

Honda/Acura Accessories Signal Mirror Manual Installation Instructions

Download
INCLUDED ITEMS: 1 left and 1 right Signal® mirror 1 left and 1 right wire harness 2 wire taps 2 ring connectors 1 instruction manual 2 nylon cable ties 2 installation tubes REQUIRED TOOLS: Ratchet with extension or ratcheting screwdriver 10mm socket Medium Philips screwdriver Non-scratchable Pry bar (Nylon) Gopher wire Needle nose pliers Wire crimper and stripper Masking tape Multimeter Sturdy gloves Safety glasses or goggles Dremel Tool.
1. Open the driver side door and lower the window. 2. Remove the tweeter pod by pulling it away from the door starting at the top section. 3. Remove speaker grill using a small screwdriver to pull up the side under the armrest using the small screwdriver indention. Once you pull up the back slide the grill backwards to release the front. 4. Remove 3 brass speaker screws to remove speaker and disconnect wiring. Remove 3 black screws holding door panel.… Read More

Honda / Acura Transponder Interface: TYPE “C”

Download DATA to DATA PORT (D 2D) : of D2D Cable plugs into the upgradeable vehicle interface module. OPTION A: – D2D Port used to connect to USB Bootloader adaptor & computer to download & flash vehicle interface firmware. OPTION B: – D2D Port used to connect to the data port of a remote control system equipped with ClearCode V ehicle I nterface P rotocol. Remote control systems designed with ClearCode VIP can securely communicate via the D2D cable to transmit & receive data commands which initiate specific vehicle function such as doorlocks & immobilizer override and /or request information from the vehicle such as status of entry points (doors) or ambiant température, diesel glow plug etc… ClearCode VIP represents the doorway to vehicle integration…As an enhanced security feature, this upgradeable vehicle interface module automatically detects when the Vehicle Interface Protocol is present and deactivates the analogue override input wire (brown wire) ensuring that this module can only be activated by an authorized user.… Read More

1997 BUICK REGAL RADIO REMOVAL AND IN-DASH INSTALLATION

Download Note: the factory radio provision is for a gm oversize radio chassis. An installation kit is recommended for aftermarket installations. We recommend the use of a scosche gm1580 kit for normal installations of din or shaft radios, or gm1590 kit for custom installations of japanese double din iso or 2 stacked din iso radios. 1. Unsnap gear selector trim bezel, unplug and remove the bezel. Extract (2) 10 mm bolts from metal console bracket. 2. Open armrest storage, lift up rubber mat and extract (2) 10 mm bolts from underneath. 3. Extract (2) 10 mm bolts from the front sides of the console, concealed up under the dash. 4. Slide shifter back into low gear, push down on spring- loaded shifter trim and pull complete center console to rear of the vehicle, allowing the center lower dash section (attached) to unsnap from the dash. 5. Extract (1) screw from bottom lower dash panel at right of glove box.… Read More