2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Download 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9.… Read More

1999 Chrysler Truck Blend Door Actuator Replacement

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More

2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

2001-2006 Acura MDX Signal Mirror Installation Instructions

Download For 1999-2004 Honda Odyssey, 2003-2006, 2007* & 2008* Honda Pilot, and 2001-2006 Acura MDX. Door Panel Removal 1. Open the driver side door and lower the window. 2. Remove the tweeter pod by pulling it away from the door starting at the top section. 3. Remove speaker grill using a small screwdriver to pull up the side under the armrest using the small screwdriver indention. Once you pull up the back slide the grill backwards to release the front. 4. Remove 3 brass speaker screws to remove speaker and disconnect wiring. Remove 3 black screws holding door panel. 5. Open screw cover in door handle using small screwdriver to lift the rear of the cover and then remove screw. 6. Push casing forward until the rear edge can be pulled away from door (you may want to use lever as though you are opening door) and use a small screwdriver to release handle rod.… Read More

2001 PEUGEOT 306 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, driver’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 2 mm2 RED wire located at the position nr. 1 in the 15 way black connector of the central unit of the central locking placed under the central tunnel. – 31: connect directly to the car body. As alternative, connect directly to the negative pole of the battery. IGNITION WIRE + 15/54: connect to the wire located at the position nr. 5 of the 15 way black connector of the central unit of the central locking placed under the central tunnel. DIRECTION INDICATORS Connect to the WHITE wire at the position nr. 10 and to the BEIGE wire at the position nr. 2 located in the 15 way black connector of the central unit of the central locking placed under the central tunnel.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

2001 Mazda Truck MPV DX FRONT DOOR DISASSEMBLY/ASSEMBLY

Download 1. Lower or raise the front door glass so that the distance from the top of the front door glass at the rear end to the upper part of the front molding is 185 mm {7.3 in} 2. Disconnect the negative battery cable. 3. Remove the front door trim.4. Disassemble in the order indicated below. 1. Inner handle 2. Front door trim bracket 3. Door screen 4. Front door glass 5. Front manual window regulator 6. Front power window regulator 7. Glass run channel 8. Front door lock 9. Outer handle 10. Door key cylinder 11. Door weatherstrip 12. Door lower weatherstrip 5. Assemble in the reverse order of disassembly. Front Door Glass Disassembly Note 1. Remove the front door glass installation bolts. 2. Slant the front door glass as shown, and remove the front door glass from the inside of the front door. Outer Handle Assembly Note 1. Connect the door key cylinder harness of outer handle as shown.… Read More

1997-2003 Honda CRV Signal Mirror Manual Installation Instructions

Download
Door Panel & Mirror Housing Removal 2002-2003 Honda CRV:1. Open door and lower window. 2. Remove plastic cover from corner of door. 3. Pop-out and remove plastic inserts. 4. Remove door handle plastic cover. 5. Unscrew the (2) screws revealed by the removal of the door handle cover. 6. Pry out door handle as shown. Disengage latch behind door handle and remove door handle. 7. Remove the (2) screws beneath armrest. 8. Lift up and pull door panel out slightly as shown. Disconnect any wiring connection behind door panel. Remove door panel from door. 9. Unscrew the (3) nuts holding the mirror housing to the door. Remove mirror housing from door.
Door Panel & Mirror Housing Removal 1997-2001 Honda CRV : 1. Open door and lower window. 2. Remove screw and plastic grommet on inside corner of door. 3. Remove plastic cover from corner of door. 4. Disconnect the mirror wire harness.… Read More

1995 Pontiac Sunfire Engine Control Module

Download Module: All Technical Service Bulletins Recall – Corrosion/Moisture Entering the PCM Product Emission 99090 – PCM Corrosion/Moisture Intrusion #99090 99090–PCM Corrosion/Moisture Intrusion (Install Protective PCM Shield/Cover Assembly) Certain 1997, 1998 and 1999 Chevrolet Cavaliers and Pontiac Sun fires Located in Fifteen U. S. High Road Salt Corrosion States (CT, IL, IN, MA, ME, MN, NH, NJ, NY, OH, PA, RI, VT, and WI) and in Ontario, Quebec and Atlantic Provinces, and Certain 1995, 1996, 1997, 1998 and 1999 Chevrolet Cavaliers and Pontiac Sunfires located in Manitoba, Saskatchewan, Alberta, British Columbia, the Yukon and Northwest Territories. Condition General Motors has decided to conduct a Voluntary Emission Campaign involving certain 1997, 1998 and 1999 Chevrolet Cavalier and Pontiac Sun fire model vehicles located in fifteen U. S. high salt corrosion states and in Ontario. Quebec and Atlantic provinces; and certain 1995, 1996, 1997, 1998, and 1999 Chevrolet Cavalier and Pontiac Sunfire model vehicles located Manitoba, Saskatchewan, Alberta, British Columbia, the Yukon and Northwest Territories.… Read More