Audi A8 Parrot 3100 Bluetooth Kit Installation Instructions

Download Installing a Parrot 3100 Bluetooth Kit in a D3 Audi A8. This procedure is to be used in conjunction with the audipages.com checklist, wiring diagram and wiring table supplied with your kit. Remove Fuse SB13 Remove the left hand side fuse panel. This is accomplished by popping the cover off with a trim stick. Once complete, REMOVE fuse SB13 (the fuse labled 13) , which is the unswitched power to the Telematics/telephone box before starting. This will prevent inadvertent grounding of the power supply during installation. Remove Trim and Telematics Box Remove the door kick panel trim by prying it up on the aft portion of it and unclipping it, then pull the vertical portion out, it just clips out. Remove the driver’s side floor mat. Using a Torx T-35 screwdriver, remove the screw that holds the left foot rest in place. Be careful when removing the screw not to drop it down into the floor board.… Read More

2001 Chevrolet Chevy K Silverado Transmission Stuck in Second or Third Gear

Download Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit ) Models: 2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) Condition Some customers may comment on one or more of the following conditions: Upon investigation, one or all of the diagnostic trouble codes (DTCs) P0740, P0753, P0758, P0785, P0787, P0973, P0976, P1860, P2761, P2764 and P2769 may be set depending on the vehicle. Cause The most likely cause of this condition may be a loss of voltage to the transmission solenoid power supply circuit. This condition may also be the result of an incorrect installation of an aftermarket electronic device such as a remote starter or alarm system.… Read More

2005 PEUGEOT 407 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download
GENERAL CONNECTIONS FOR INSTALLATION ALARM/SIREN POSITION Position the compact alarms and the sirens under the dashboard driver’s side. Pass the cables using the original fairlead located behind the servobrake group. POWER SUPPLY +30: connect to the 3 mm2 YELLOW wire, at the position nr. 2, of the 2 way grey/black connector, on the coming out of the anterior part of the “BSI” central. As alternative it is possible to connect to a 8 mm2 threaded pin located in the anterior part of the fuse box. -31: connect directly to one of the ground terminals located under the dashboard, driver’s side. IGNITION WIRE +15/54: connect to 1 mm2 LEIGHT BLUE wire marked “77C”, in the grey connector located inside the tinned box in the engine compartment, driver’s side. DIRECTION INDICATORSConnection right direction indicator Connect to the 0,75 mm2 GREY wire marked 2345, in the black connector marked “GRIS” located inside the tinned box in the engine compartment, driver’s side.… Read More

1988-1991 Honda Civic Si FUSES and CIRCUIT BREAKERS

Download IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)Fuse & Circuit Breaker Identification z 1 – 60 Amp Power Distribution z 2 – 50 Amp Dash Fuse Box z 3 – 40 Amp Dash Fuse Box, Exterior Lighting z 4 – 10 Amp PGM-FI Electronic Control Unit, Hazard Lights, A/T Control Unit (Wagon), Integrated Control Unit (1990), Automatic Shoulder Belts (1990) z 5 – 15 Amp Horns, Brakelights, A/T Control Unit (Wagon Only), Key Interlock Solenoid (A/T Only), Seat Belt Retractors (1990) z 6 – 20 Amp Rear Window Defogger z 7 – 15 Amp PGM-FI Main Relay z 8 – 15 Amp A/C Compressor Clutch, Condenser Fan Relay… Read More

Audi A8 D3 Sony HCB-30 Bluetooth Kit Installation Checklist

Download kit Torx T-35 screwdriver Soldering iron Solder Heat gun or other heat source to heat shrink tubing Drill with 3/8″ bit Small wire cutters Wire strippers that go down to 20 gage wire Electrical Tape Drop or Flash Light Hanger for pulling wire Step Description Completed (check) 1 Place Telematics box in Service Mode. 2 Remove Fuse SB13. 3 Remove driver’s side trim and Telematics box from under carpet. 4 Disconnect wiring from Telematics box. Drill hole for wiring harness. Modify six connections on the 42 pin connector. 5 Install cover on 42 pin connector, plug into Telematics box, install Fuse SB13. Plug all components into HCB- 30 brain box, turn on ignition and test. 6 Mount HCB-30 brain box, run wiring. 7 Replace Telematics box, replace carpet. 8 Mount and route the microphone and wire. 9 Mount and route the touch pad and wire. 10 Take Telematics box out of Service Mode.… Read More

2002-2006 ACURA RSX Type-S Intake System PART 21-506

Download PART NUMBER: 21-506 2002-2006 ACURA RSX Type-S L4-2.0L C. A. R. ine has run in the past two hours, let it cool down. d. Disconnect both the negative and positive battery terminals. e. Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle. Support your vehicle using properly rated jack stands before wheel removal or while working under the vehicle. NEVER WORK UNDER A VEHICLE WITHOUT USING JACK STANDS. i. Remove the front left wheel. ii. Remove the left fender well lining and remove the lower splashguard. f. This intake system includes a replacement windshield washer system. g. Do not discard stock components after removal of the factory system. 2. Removal of stock system a. Factory air box system. b. Remove the two mounting bolts securing the upper engine cover. Remove the engine cover. c.… Read More

Peugeot 106 Dog Engagement Gear-Box Mounting Instructions

Download
Changes to be made to the original parts in order to have a correct mounting of the Bacci-production gear-box. 1. Installation of the supplied lock plate for the two ball bearings. In the kit we supply n° 4 hexagonal head bolts, n° 2 bearing locking rings (Seeger- type) and a lock plate (see photo n°1). The kit has to be applied to the central box of the gear group (photo n°2) and it modifies the production model bearing locking system. The 4 bolts and the 2 rings replace the original parts. Mount the Bacci gear-box and lock the two ball bearings with the supplied Seeger- type rings. After that, lock the two bearings with the plate and the bolts you found in the kit (photo n°3). Be careful to screw the 4 bolts at 3 kgm with a dynamometric wrench and to lock them with Loctite. 2. Application of the support (supplied with the kit) to the central box.… Read More

WDS COP KIT DIAGNOSTIC TIPS COIL ON PLUG (COP) IGNITION SYSTEMS ENGINE MISFIRE OR ROUGH RUNNING

Download 1998-2002 Continental FORD: 1998-2006 Town Car 1996-1999 Taurus SHO 2000-2006 LS 1998-2006 Crown Victoria, Mustang 1998-2006 Navigator 2000 Taurus 2002-2003 Blackwood 2002-2005 Thunderbird 2003-2005 Aviator 2003-2006 Focus 2004-2006 Taurus MERCURY: 2005-2006 Five Hundred, Freestyle 1998-2006 Grand Marquis 1997-2006 E-Series, Expedition, F-150 2000 Sable 1999-2006 F-Super Duty 2004-2005 Sable 2000-2005 Excursion, F-53 2005-2006 Montego 2001-2006 Escape 2002-2005 Mountaineer 2002-2005 Explorer 2005-2006 Mariner 2005-2006 Escape Hybrid 2006 Mariner Hybrid LINCOLN: 1997-1998 Mark VIII. This article supersedes TSB 04-16-01 to update the SERVICE PROCEDURE vehicle applications and model years. The optional WDS COP Kit available through NOTE Rotunda will provide more accurate diagnosis and help reduce replacement of non-defective parts. The FOLLOW THIS TSB PROCEDURE ONLY IF Kit (418-FS528) can be purchased through THERE ARE NO SPECIFIC MISFIRE TSBs/SSMs 1-800-ROTUNDA. RELEASED FOR THE VEHICLE SYMPTOM BEING EXPERIENCED. The following material will detail the diagnostic steps on WDS to take the guesswork out of misfire ISSUE diagnosis using the COP Kit.… Read More

Kit Number 57-0662 Installation Instructions

Download Citroen C4 1.6Hdi 2004-2009, Citroen Berlingo 1.6L 2005-2009, Citroen C2 1.6Hdi 2005-2009, Citroen C3 1.6Hdi 2008-2009, Citroen C3 Picasso 1.6Hdi 2009, Citroen C4 Picasso 1.6Hdi 2006-2009, Citroen C5 1.6Hdi 2005-2009, Mini Cooper 1.6Hdi 2007-2009, Mini Cooper Clubman 1.6Hdi 2007-2009, Peugeot 207 1.6 2006-2009, Peugeot 308 1.6 2007-2009, Peugeot 407 1.6 2005-2009, Peugeot Partner 1.6 2006-2009.
Parts list: 1 x Air filter Element. 1 x Silicone Intake Hose. 1 x Flexi Cold Air Hose. 1 x Metal Adaptor Hose. 1 x Literature Pack. Fixing Kit :- 3 x Plastic Tie. 3 x #44 Hose Clamp. 1 x Mounting Bracket. 1 x M6 Nylock Nut. 2 x M6 Flat Washer. 1 x Hex Head Bolt M6x20.
Instruction sheet A2054-768 1. Disconnect the negative terminal from the vehicle battery. 2. To the install induction kit it is necessary to remove the bulkhead trims: 3. Unclip & remove the side cover surrounding the washer bottle etc.… Read More

1994 Mercury Cougar XR7 INTERIOR FUSE PANEL IDENTIFICATION

Download 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. INTERIOR FUSE PANEL IDENTIFICATION (1994-95 MODELS) On all models, the fuse panel is located under the instrument panel, left of the steering column. Fuse & Circuit Breaker Identification 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module 10 – 10 Amp OBD-II Test Connector 11 – Not Used 12 – 5 Amp Illumination Of: Cluster, Phone Switch, Rear Defrost Switch, A/C Switch (Manual), PRNDL Indicator, Ashtray, EATC, Clock, Radio 13 – 20 Amp Cigarette Lighter, Flash-To-Pass 14 – 15 Amp Speed Control Module, ABS Module, BrakeShift Interlock, High Mount Brakelight, Brakelights, Flashers 15 – 5 Amp Cluster (Gauges), Cluster (ABS & Airbag Warning), Warning Chime, Autolight Sensor 16 – 10 Amp Integrated Module, Sport Voltmeter, Speed Control, Remote Keyless Entry, Anti-Theft, Power Window/Door Lock Switch Illumination, Radio, CD Changer, Power Antenna, Clock 17 – 30 Amp Wiper/Washer System 18 – 20 Amp Power Door Locks, Decklid Release, Fuel Door Release, Power Seats, Power Lumbar, Booster 19 – 20 Amp Power Window Motors, Moon Roof Motor UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron.… Read More