1999 – 2001 Honda Accord Radion Replacement Installation Instructions

Download
Remove Factory Radio NOTE : To remove the radio, the center dash panel surrounding the radio must be removed. There are three (3) phillips screws that secure this dash panel to the main dash assembly. However, (1) one of the screws is hidden behind the clock. STEP 1 : The clock unsnaps from the dash panel, but requires a very small flat head screwdriver or similar flat tool. Insert the tool into the side gap between the edge of the clock assembly and the dash panel. GENTLY, pry out that edge of the clock. Insert your fingers into the gap and pull firmly to completely remove the clock from the dash panel. Once the clock has been pulled out, unplug the plastic connector attached to the rear of the clock. STEP 2 : Once the clock assembly has been removed locate and remove one (1) phillips screw. STEP 3 : Look on the curved underside of the dash panel.… Read More

1999-2001 Honda Accord Accessories Radio Replacement Instructions

Download
Remove Factory Radio. STEP 1 : The clock unsnaps from the dash panel, but requires a very small flat head screwdriver or similar flat tool. Insert the tool into the side gap between the edge of the clock assembly and the dash panel. GENTLY, pry out that edge of the clock. Insert your fingers into the gap and pull firmly to completely remove the clock from the dash panel. Once the clock has been pulled out, unplug the plastic connector attached to the rear of the clock. STEP 2 : Once the clock assembly has been removed locate and remove one (1) phillips screw. STEP 3 : Look on the curved underside of the dash panel. Locate and remove two (2) phillips screws. STEP 4 : All screws securing the dash have now been removed. The plastic dash panel itself snaps into the main dash assembly. Begin by pulling gently on either the bottom curve of the dash panel or one of the top corners of the dash panel.… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

AUDI NEW BEETLE ECU INSTALLATION

Download 1 Remove the Dash Panel. Place both hands on either side of the center dash panel, firmly grip and slide forward, then lift. Step 2 Remove Upper Dash Panel Screws. Remove the four T-20 torx screws securing the upper dash panel. Step 2 Remove the Upper Dash Panel. To remove the upper dash panel, firmly pull the panel upwards being careful not to damage it. Step 3 Remove Lower Dash Panel. Underneath you will find the ecu housing cover. Remove the torx T-20 screws that secure the cover. Pull the ECU housing cover upward to expose the ECU. Step 4 Remove the ECU. To remove the ECU wiring harness, pull the tabs on harness away from the ECU. As this is done, the harness connector will pull away from the ECU. The reinstallation of the ECU is the reverse of the removal. Step 5 Installing the Fuel Pressure Regulator. Depending on the ECU version of your Beetle, an upgraded FPR may be required.… Read More

1997 BUICK REGAL RADIO REMOVAL AND IN-DASH INSTALLATION

Download Note: the factory radio provision is for a gm oversize radio chassis. An installation kit is recommended for aftermarket installations. We recommend the use of a scosche gm1580 kit for normal installations of din or shaft radios, or gm1590 kit for custom installations of japanese double din iso or 2 stacked din iso radios. 1. Unsnap gear selector trim bezel, unplug and remove the bezel. Extract (2) 10 mm bolts from metal console bracket. 2. Open armrest storage, lift up rubber mat and extract (2) 10 mm bolts from underneath. 3. Extract (2) 10 mm bolts from the front sides of the console, concealed up under the dash. 4. Slide shifter back into low gear, push down on spring- loaded shifter trim and pull complete center console to rear of the vehicle, allowing the center lower dash section (attached) to unsnap from the dash. 5. Extract (1) screw from bottom lower dash panel at right of glove box.… Read More

2006 Honda Civic SI Comptech Supercharger Kit Installation Instructions

Download STEP #1 Evacuate A/C system: • Have your local Air conditioning shop remove the HFC-134a refrigerant from your A/C system. They can reuse your coolant. After the supercharger installation you will need to return the car to them and have them refill and charge the system. This service should cost approximately $80.00. STEP #2 Remove ECM and ship to Hondata: • Remove the battery. • Remove ECM cover (A). • Remove bolts (D), then lift up the ECM. • Disconnect the ECM connectors A, B, and C. • Remove ECM and ship to Hondata (see Address to right.) STEP #3 Drain Coolant: • Jack up and support the front of the car on jack stands. • Make sure the engine is cool and remove the radiator cap. • Drain the cooling system by loosening the drain plug (A) at the bottom of the radiator. • Once all of the coolant is drained close the drain plug.… Read More

1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Download FORD Edge 2007-2009 / Expedition 2007-2009 Explorer 2006-2009 / Explorer Sport Trac 2006-2009 F-150 2004-2008 / F Series 2005-2008 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2009 Mustang 2005-2009 / Super Duty 2008-2009 Taurus 2008-2009 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2009 Sable 2008-2009 LINCOLN Mark LT 2005-2009 Factory Navigation Only: MKX 2007-2009 / Navigator 2007-2009. DASH DISASSEMBLY A B C D E FORD MUSTANG 2005-2009 Remove the small rectangular shifter lever trim panel if equipped . (Figure A) 2 Remove (4) 9/32″screws from the radio to remove. (Figure E) 7 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (includingcup holders). (Figure B) 3 Unclip and remove panel. (Figure B) 4 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls.… Read More

1994 – 1998 Honda Accord Radio Replacement Installation Instruction

Download
Remove Factory Radio
STEP 1 : The center dash console must be loosened and pulled away in order to gain access to screws securing the plastic dash panel surrounding the radio. Open the center console glove box. At the very bottom is a plastic panel that covers hidden screws. With your fingers or a flat head screwdriver, lift up and remove the plastic panel. Once the panel is removed, locate and remove two (2) phillips screws. STEP 2 : Lift open the drink tray door. Pull the drink tray up and pull it out of the center console.STEP 3 : Once the drink tray is removed, locate and remove three (3) phillips screws. (2) screws will be at the bottom of the panel, and (1) will be at the front left corner near the top of the opening. STEP 4 : Once the three screws have been removed, the center console can be pull back, away from the gear shift console.… Read More

2002 Buick Truck Rendezvous Trim Panel Replacement

Download Tools Required J 38778 Door Trim Pad and Garnish Clip Remover Removal Procedure 1. Open the door. 2. Disconnect the power window switch assembly. 3. Remove the screws from the front door trim panel 4. Use the J 38778 to remove the trim panel. 1. Reposition the electrical harness connectors. 2. Remove the trim panel from the vehicle. Installation Procedure Important: Before installing the front door trim panel , discard the old trim panel retainers and replace with NEW trim panel retainers. 1. Install the new retainers to the front door trim panel . 2. Route the electrical connectors through the trim panel . 3. Align the trim panel to the door inner panel, guiding the door handle through the trim panel. 4. Install the upper edge of the trim panel to the top edge of the inner door panel, pressing down firmly until the trim panel is fully seated.… Read More