2003 Cadillac Escalade Code C0660 will reset.

Download Vehicle Application: 2003 Cadillac Escalade 5.3L, Vin T, USA/Canada 2005 Chevrolet Suburban 1500 LS 5.3L, GAS, Vin T 2003 Cadillac Escalade EXT 6.0L 2005 GMC Yukon XL 1500 Slt 5.3L, FLEX, Vin Z 2005 Chevrolet Suburban 1500 LS 5.3L, FLEX, Vin Z Customer Concern: Code C0660 will reset. Tests/Procedures: 1. Check the RTD fuse located in the underhood fuse block. 2. Check for Battery Voltage (B+) on the Orange wire at the automatic level control air compressor pin F. 3. If less than B+ at pin F, check for a wiring and connection problem between the air compressor and the underhood fuse block. 4. Disconnect the compressor leveling module connector and check the resistance from the positive battery voltage circuit of the exhaust solenoid valve and the control circuit of the exhaust solenoid valve. Should be 30-90 ohms. 5. Check for B+ on the Dark Blue wire pin B at the air compressor with the exhaust solenoid commanded off.… Read More

1997-2002 FORD EXPEDITION REPEAT AIR SUSPENSION COMPRESSOR DRIER FAILURES

Download Some 1997-2002 Expedition 4X4 and 1998-2002 COMPONENTS AS HIGH PRESSURE IS VENTED Navigator 4X4 vehicles equipped with 4-wheel air UNCONTROLLED. suspension, may exhibit repeat air compressor drier If diagnostics lead to compressor/dryer assembly failures. The drier cap may become detached from replacement, use the following service procedure to the drier body, or the drier body may be broken at insure complete and thorough service. the neck near the compressor head. This may be due to incomplete or incorrect system diagnosis that 1. Using the New Generation STAR (NGS) tester, leads to replacement of only the original air vent the compressor/drier assembly. suspension compressor, despite the fact that the compressor is not the root cause of the concern. 2. Using regulated shop air, blow out the air lines Compressor failure in these instances is only a from the drier to the front fill solenoid valve, symptom of an underlying system problem.… Read More

2006 Dodge Truck RAM DENSO A/C COMPRESSOR

Download 2006 Dodge Truck RAM 2500 Truck 2WD L6-5.9L DSL Turbo VIN C Vehicle Level Heating and Air Conditioning Compressor HVAC Compressor Clutch Service and Repair Service and Repair. DENSO A/C COMPRESSOR REMOVAL NOTE: * The compressor clutch assembly can be serviced with the refrigerant system fully-charged. * Typical A/C compressor shown in illustrations. 1. Disconnect and isolate the negative battery cable. 2. Remove the accessory drive belt. 3. Disconnect the engine wire harness from the compressor clutch field coil connector (1) located on the top of the A/C compressor (5). 4. Remove the bolts that secure the A/C compressor to the engine and support the A/C compressor. 5. Carefully remove the compressor clutch field coil connector and wire lead from the connector bracket (2). 6. Remove the compressor shaft bolt (3). A band-type oil filter wrench or a strap wrench may be used to hold the clutch plate (4) from rotating during bolt removal.… Read More

2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Download FORD Edge 2007-2009 / Expedition 2007-2009 Explorer 2006-2009 / Explorer Sport Trac 2006-2009 F-150 2004-2008 / F Series 2005-2008 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2009 Mustang 2005-2009 / Super Duty 2008-2009 Taurus 2008-2009 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2009 Sable 2008-2009 LINCOLN Mark LT 2005-2009 Factory Navigation Only: MKX 2007-2009 / Navigator 2007-2009. DASH DISASSEMBLY A B C D E FORD MUSTANG 2005-2009 Remove the small rectangular shifter lever trim panel if equipped . (Figure A) 2 Remove (4) 9/32″screws from the radio to remove. (Figure E) 7 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (includingcup holders). (Figure B) 3 Unclip and remove panel. (Figure B) 4 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls.… Read More

2005 Chevrolet Chevy K Silverado Panel Cluster Gauge Needle Function

Download Subject: 07187C — SPECIAL COVERAGE ADJUSTMENT – INSTRUMENT PANEL CLUSTER GAUGE NEEDLE FUNCTION Models: 2003-2004 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT 2005 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT (U.S. ONLY) 2003-2004 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE 2005 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE (U.S.ONLY) 2003-2004 GMC SIERRA, YUKON, YUKON XL 2005 GMC SIERRA, YUKON, YUKON XL (U.S. ONLY) Condition Some customers of all 2003-2004 model year and certain U.S. 2005 model year Cadillac Escalade, Escalade ESV, and Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, and Tahoe; and GMC Sierra, Yukon, and Yukon XL vehicles have reported that one or more of the instrument panel (IP) cluster gauges stick, flutter, or become inoperative. This may cause inaccurate readings, including the speedometer and fuel gauge. Special Coverage Adjustment This special coverage covers the condition described above for a period of 7 years or 70,000 miles (110,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership.… Read More

2000-2005 FORD 4WD EXCURSION 4″ SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS

Download Requires the following parts (sold separately) for a complete installation: • Front Leaf Springs – P/N 60SD2 • Hardware Kit – P/N 6000HE • Box Kit – P/N 6005B. FRONT OF VEHICLE – DISASSEMBLY AND ASSEMBLY 1. Park vehicle on level, hard (concrete) surface. 2. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction and set parking brake. 3. Remove front bumper by removing (2) outer 13mm brace bolts and the (4) 18mm bolts from front of bumper. If the vehicle contains a crash bar below the bumper, it must be removed. To accomplish this, remove the (6) 21mm nuts. While supporting the bumper, disconnect the (2) lighting harness plugs and wiring harness from bumper (if applicable), and the (3) plastic push clips in the rubber shield. Carefully remove bumper, making sure not to scratch the paint on the front fenders. 4. To make access to spring eye bolts, remove (2) 8mm bolts at the lower corner supports of air conditioning cooler and remove supports.… Read More

2005 Peugeot 307 Digital Music Changer Installation Guide

Download Compatible with: CITROEN C2/C3/C4/C5/C6 & C8 with Blaupunkt/VDO RD4 head unit PEUGEOT with Blaupunkt/VDO RD4 head unit Peugeot 307 (>2005) Peugeot 607 (>2005) Peugeot 807 (>2005) Peugeot 407 (>2005) Peugeot 207 (>2006) Peugeot 308 (>2007) Peugeot 307sw (>2005) Peugeot 407sw (>2005).
Installation Guide: Caution : Before the installation of DMC, you need make sure the cd changer option of Citroen or Peugeot head unit is been set on. Otherwise you need go to dealer to open the cd changer option. 1. Before the installation, power off the car 2. Plug the Digital Music Changer into your car stereo changer port (usually located behind the radio) 3. Insert the USB disk or SD Card (Please consult user manual about setting music files in the USB disk or SD Card) 4. For PC, PSP, MD, Mobile Phone etc aux device, connect it with Aux in port 5. Once the unit is installed, power on the radio, then press the Source button, you will then have the following control: Disk+/Disk-, Next track, Previous track, Fast Forward & Fast Rewind etc.… Read More

2005 Ford Mustang GT Roush Fog Lamp Wiring Harness Installation Instructions

Download 1. SAFETY REQUIREMENTS STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation. 1. Always wear safety glasses for eye protection. 2. Place ignition switch in the OFF position. 3. Always apply the parking brake when working on a vehicle. 4. Block the front and rear tire surface to prevent unexpected vehicle movement. 5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. 6. Do not smoke or use flammable items near or around the fuel system. 7. Use chemicals and cleaners in well-ventilated areas. 8. Batteries produce explosive gases, which can cause personal injury.… Read More

1997-2002 FORD EXPEDITION 4WD 5″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

Download Before Starting Installation 1. Carefully read all warnings and instructions completely before beginning. 2. Verify all parts have been received in this kit by checking the parts list at the end of this document. 3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175. 4. Special tools needed a. Torsion bar removal tool b. Brass drift c. 9/32″ & 1/2″ drill bit d. Tie Rod Puller 5. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Ride Height (For IFS w/ torsion bars) 1. Measure ride height with the vehicle supporting its own weight on level ground. To settle the suspension, the vehicle should be driven forward at least 10 feet immediately prior to taking these measurements.… Read More

2001-2005 Honda GL1800 Audio Amplifier Manual Installation Instructions

Download
This sheet must be read completely to: 1. Provide assistance/clarification to the installer. 2. Avoid causing injury to installer, customer, end user, or others. 3. Prevent damage to motorcycle and/or accessory. 4. Prevent death to customer or other vehicle operators . Installer: Please forward this sheet to the customer after reviewing it. 5. It is virtually impossible for us to be able to address every possible situation an installer or user will encounter. This requires both to exercise due diligence and to apply some level of common sense. If you have any question or problem during the installation, please contact us as necessary. Read the instructions completely prior to installation. 90% of questions we receive could be answered simply by reading the instructions in their entirety. Phone support will always provide the quickest response. Important Information in our instructions will be provided in the following manner: 6. SHOP TIP: this is information we have gathered from hands-on installs or customer feedback.… Read More