2004 ford explorer brake light fuse location

You search Auto repair manual PDF about 2004 ford explorer brake light fuse location, search results will appear below. If search results do not exist, please search by others keyword.

2000-2004 Audi TT Coupe Brake System

Filed Under (Audi) by admin on 31-12-2013

Download Audi TT Coupe 2000-2004, Audi TT Roadster 2001-2004 – Brake System. ABS/ESP ITT Mark 20 system components, removing and installing Brake light switch (square housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once. Removing – Remove storage compartment on driver’s side. Repair Manual, Body Interior, Repair Group 68; Storage compartments, covers – Unplug electrical connector. – Remove brake light switch -1- by turning counter-clockwise through 90. Installing Install in reverse sequence; note the following points: – Pull brake light switch plunger fully out. – Press brake pedal down as far as possible by hand. – Guide switch through installation hole and secure by turning 90 clockwise -arrows-. – Release brake pedal. – Make sure proper function of brake lights when brake pedal is pressed and released. Brake light switch (round housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once.… Read More

2004+ Acura TSX Rear Big Brake Kit Installation Instructions

Filed Under (Acura) by admin on 09-12-2013

Download Step 1 Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels For a rear kit installation, block the front wheels, and release the parking brake. Then break loose the lug nuts on both rear wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle. Jack up the vehicle, and secure it on a pair of jack stands, again referring to the Owner’s Manual for jack location joints. After securing the vehicle at a convenient height, remove the rear wheels. Step 2 Disconnect Stock Brake Line Loosen the hard line fitting from the stock brake line, using a 10mm flare wrench. Place a drip tray or several rags directly below the inboard brake line connection. If the area around the brake line connection to the chassis is dirty, clean it using brake cleaner or an appropriate cleaning agent.… Read More

2004 Ford Expedition/Navigator Brake Pads REMOVAL AND INSTALLATION

Filed Under (Ford) by admin on 28-12-2013

Download NOTE: Verify if the anchor housing spring has 1. CAUTION: Install a new lining if worn 1 end with 2 tabs. If yes, the LH side anchor to or past the specified thickness above the housing spring must be installed with the metal backing plate or rivets. Install new 2-tabbed end in the upper brake caliper cavity. pads in complete axle sets. For the LH brake caliper, release the lower If necessary, using a suitable suction device, portion of the anchor housing spring. remove the brake fluid in the master cylinder •Apply force at the center of the anchor reservoir until it is half filled. housing spring and pull outward at the bottom of the anchor housing spring to 2. Remove the wheel and tire assembly. For remove it from the lower brake caliper additional information, refer to Section 204-04. cavity. 3. Inspect the brake pads for wear or contamination.… Read More

2004+ Acura TSX Front Axle Kit

Filed Under (Acura) by admin on 03-02-2014

Download Step 1 Raise Vehicle, and Remove Wheels For a front kit installation, apply the parking brake, then break loose the lug nuts on both front wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle. Jack up the vehicle, and secure it on a pair of jack stands, again referring to the Owner’s Manual for jack location joints. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. After securing the vehicle at a convenient height, remove the front wheels. Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake must be applied before removing the front must be applied before removing the front must be applied before removing the front must be applied before removing the front must be applied before removing the front wheels.… Read More

1999 – 2002 Ford F-150 2WD and Ford Expedition Front Big Brake Update

Filed Under (Ford) by admin on 01-01-2014

Download Kit Contents Your StopTech Big Brake kit includes the following: 1 pair of ST-40 four-piston calipers, sized specifically for the vehicle 1 set of high-performance street pads (not suitable for track use) 1 pair of 355 X 32mm two-piece rotor assemblies 1 pair of aluminum caliper adapter brackets 2 pair of 7/16-20 self-locking Jet nuts 2 pair of 12mm washers 1 pair of hub assemblies 1 pair of stainless steel brake lines 1 pair of Adel clamps 1 pair of 10mm button-head bolts (for use with the Adel clamps) 1 pair of self-locking nuts (for use with the Adel clamps) 1 pair of banjo bolts 2 pair of copper crush washer s 1 pair of rubber end caps. Tools and Equipment Required Different models and years of vehicle use different-sized fasteners, and every effort has been taken to correctly identify the proper sized tool for each step of the installation.… Read More

2003 Volvo S40 Replacing The Rear Brake Pads

Filed Under (Volvo) by admin on 29-12-2013

Download 2003 Volvo S40 L4-1.9L Turbo VIN 27 B4204T4 Vehicle Level Brakes and Traction Control Disc Brake System Brake Pad Service and Repair Rear Brake Pads. Replacing The Rear Brake Pads Special Tools: 999 5782, 951 2834 General CAUTION: Replace the brake pads when the minimum thickness is 2 mm . Removing the rear brake pads Remove * the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers. Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective.… Read More

2007 Volkswagen Rabbit Brake pads, removing and installing

Filed Under (Volkswagen (VW)) by admin on 09-12-2013

Download 2007 Volkswagen Rabbit BRAKES Brake System. Brake pads, removing and installing Special tools, testers and auxiliary items required. Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! * Remove wheels. * Disconnect connector – 1 – for brake pad wear indicator. * Remove caps – arrows -. * Loosen both guide pins – arrows – and remove from brake caliper. * Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. * Remove brake pads from brake caliper. Cleaning: * Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. * Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir.… Read More

2004 Ford Truck Explorer ERRATIC FUEL GAUGE OPERATION

Filed Under (Ford) by admin on 27-12-2013

Download 2004 Ford Truck Explorer 4WD V8-4.6L SOHC VIN W MIL ON WITH DTC P0463 OR ERRATIC FUEL GAUGE OPERATION FORD: 2004-2007 Explorer MERCURY: 2004-2007 Mountaineer This article supersedes TSB 06-16-7 to update the Service Procedure. ISSUE Some 2004-2007 Explorer 4dr/Mountaineer vehicles may exhibit the malfunction indicator lamp (MIL) on with diagnostic trouble code (DTC) P0463 or an erratic fuel gauge concern. This could be from sulphur contamination in the fuel, causing an open or high resistance on the fuel sender card. ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. For vehicles with customer symptom of erratic fuel gauge operation (with no MIL on), proceed to Step 1a. For vehicles with a customer symptom including the MIL on, proceed to Step 1b. If unable to verify the concern, do not continue with this TSB. a. Follow the appropriate pinpoint test (PPT) for “Fuel Gauge Inaccurate” in Workshop Manual (WSM), Section 413-01.… Read More

1998 – 2001 Ford Explorer 4WD Ford Ranger Explorer Sport Trac / Edge Mountaineer 4WD Torsion bar key front leveling kit

Filed Under (Ford) by admin on 15-02-2014

Download Part # 22907 1998 – 2001 Ford Explorer 4WD 1998 – 2007 Ford Ranger / Explorer Sport Trac Edge / Mountaineer 4WD Torsion bar key front leveling kit Part# Description Qty. 22907-01 Torsion bar keys 2 22907INST Instruction manual (customer copy) 1 22907INST Instruction manual (installer copy) 1 WARNINGDECAL Warning decal 1 MIRRORHANGER Rear view mirror hanger 1. Important customer information: Tuff Country EZ-Ride Suspension highly recommends that a qualified and/or certified mechanic performs this installation. If you desire to return your vehicle to stock, it is the customers responsibility to save all stock hardware. This vehicles reaction and handling characteristics may differ from standard cars and/or trucks. Modifications to improve and/or enhance off road performance may raise the intended center of gravity. Extreme caution must be utilized when encountering driving conditions which may cause vehicle imbalance or loss of control. DRIVE SAFELY! Avoid abrupt maneuvers, such as sudden sharp turns which could cause a roll over, resulting in serious injury or death.… Read More

Compact Exhaust Brake and/or Optional Torque Converter Controller for 7.3L PowerStroke Turbo-Diesel

Filed Under (Ford) by admin on 28-12-2013

Download Exhaust Brake and/or Torque Converter Controller Kit Contents • Integrated Control Module. • Harness with labeled connections for a hassle-free install. Every possible convenience was included in the harnessing to ensure an easy installation experience. • Small Parts Bag. A baggie containing fuse taps, taps, connectors, and zip-ties and such has been included to aid your installation. • Optional Plug in Kits for your model year and make vehicle (if purchased with unit) (may also be purchased after initial sale) Tools Required: • A good DMM or DVOM (Multimeter) for probing circuits. A test light will do in a pinch, but remember that test lights can be misleading if not understood or used properly. • A good quality wire stripping/cutting/crimping tool. Your installation will only be as good as the tools used! • A wire fish (coat hanger) for running wires in tough to reach locations or through the firewall if necessary.… Read More

You might also likeclose