2000-2005 Ford Explorer Wheel Bearings REMOVAL & INSTALLATION

Download 1. Before servicing the vehicle, please familiarize yourself with safety procedures. 2. Remove the axle”to”wheel hub retainer nut and washer. 3. Remove the parking brake shoes. 4. Press the outboard CV”joint until it is loose from the hub. 5. Remove and discard the toe link”to”wheel knuckle nut. 6. Remove the bolt and separate the toe link from the wheel knuckle. 7. Remove and discard the upper arm”to”wheel knuckle nut. 8. Remove the bolt and separate the upper arm from the wheel knuckle. 9. Remove and discard the lower arm”to”wheel knuckle nut. 10. Remove the lower arm”to”wheel knuckle bolt. 11. Remove the wheel knuckle. 12. Using a suitable press, remove and discard the wheel hub. 13. Remove and discard the wheel bearing retainer ring. 14. Using a suitable press, remove the wheel bearing. Fig. Rear hub/bearing Assembly”Aviator, Explorer and Mountaineer Fig. Pressing out the bearing 1. Installation is the reverse of the removal procedure.… Read More

2002 Volvo XC70 Rear Wheel Hub Replacing

Download 2002 Volvo XC70 L5-2.4L Turbo VIN 58 B5244T3 Vehicle Level Transmission and Drivetrain Drive Axles, Bearings and Joints Wheel Hub Service and Repair Rear Wheel Hub, Replacing. Special tools: 951 2050 Raise the car Remove the rear wheel the screw for the drive shaft / wheel hub. Removing the rear wheel hub. Remove the brake caliper mounting screws. Hang the caliper up with a piece of wire the locating pin for the brake disc the brake disc the ABS-cable holder the ABS sensor. Hang up the sensor using a piece of wire. Remove the spring strut from the lower control arm Note: the spring strut is slightly compressed. Remove the anti-roll bar from the upper control arm Use a Torx wrench as a counterhold so that the rubber boot is not damaged. Remove the tie rod from the wheel spindle. Angle the tie rod upwards so that the inner mounting for the control arm is exposed the screw holding the lower mounting for the control arm to the sub-frame.… Read More

1997 Ford Aerostar/Ranger Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive DISASSEMBLY AND ASSEMBLY

Download Wheel Grease Seal and Bearing, Front Replacement and Repacking SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Impact Slide HammerT50T-100-A Bearing Cup ReplacerT80T-4000-P Driver Handle T80T-4000-W Seal Replacer T80T-4000-T Spindle Seal ReplacerT95T-3132-D. The recommended wheel bearing lubricant is lithium-base High-Temperature Constant Velocity Joint Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. -base grease is not compatible with lithium-base grease. Do not intermix. Clean all old lubricant grease prior to lubricating front/rear wheel bearing. Use of incompatible bearing lubricant could result in premature lubricant breakdown. NOTE: If bearing adjustment does not eliminate looseness or rough and noisy operation, clean, inspect and repack the hub and wheel bearings with specified wheel grease. If wheel bearing cup or the cone and roller assemblies are worn or damaged, they should be replaced. Manual Locking Hub, Ranger. Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly.… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

2004 Ford F-Super Duty 250-550/Excursion Workshop Manual

Download 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04. 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate. 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00. Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. CAUTION: Due to the fit of the splines, the hub lock will be difficult to remove.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

2000 Ford F-150 Rear Drive Axle/Differential

Download 1. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the RH kick panel area. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations. Raise and support the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the differential housing cover (4033). ? Drain the lubricant. For additional information, refer to Differential Housing Cover in this section. 4. Remove the brake calipers and discs. 5. Remove the differential pinion shaft (4211). 1. Remove and discard the differential pinion shaft lock bolt. 2. Remove the differential pinion shaft. 6. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers (4N237). 1.… Read More

Ford Super Duty 4×4 Mag Hytec Rear Diff Cover Install and Rear Diff Gear Oil Change 2004 F250 4×4 XLT Sport Crew Cab

Download TOOLS & PARTS I USED – Mag-Hytec Ford 10.5 rear differential cover – Redline #57914 75W140 gear oil, 6 quarts – 1/2″ socket & ratchet (cover bolt removal) – Flat screwdriver – Torque wrench – Drain pan – Several rags – Plastic putty paddle – Small funnel – Lacquer thinner – 1/4″ allen wrench (new cover bolt install) PROCEDURE Here’s a few pics of the Mag Hytec cover. Its a very impressive cover, complete with additional oil capacity, a magnetic dipstick, a drain plug, a 1/8 NPT port (for a temperature sending unit), and an o-ring to seal to the rear diff case. Here’s a shot of the dipstick (left) and temperature sender port. Here’s a pic of the drain plug on the bottom. Dipstick removed
Drain plug removed Here’s the stainless hardware that’s included with the cover. They also include the two sizes of allen wrenches needed for the installation of the bolts and to service the drain plug/diptstick/sender port.… Read More

2007 Toyota Camry Rear Bumper Removal and Replacement

Download REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.… Read More