2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

Ford Super Duty 4×4 Mag Hytec Rear Diff Cover Install and Rear Diff Gear Oil Change 2004 F250 4×4 XLT Sport Crew Cab

Download TOOLS & PARTS I USED – Mag-Hytec Ford 10.5 rear differential cover – Redline #57914 75W140 gear oil, 6 quarts – 1/2″ socket & ratchet (cover bolt removal) – Flat screwdriver – Torque wrench – Drain pan – Several rags – Plastic putty paddle – Small funnel – Lacquer thinner – 1/4″ allen wrench (new cover bolt install) PROCEDURE Here’s a few pics of the Mag Hytec cover. Its a very impressive cover, complete with additional oil capacity, a magnetic dipstick, a drain plug, a 1/8 NPT port (for a temperature sending unit), and an o-ring to seal to the rear diff case. Here’s a shot of the dipstick (left) and temperature sender port. Here’s a pic of the drain plug on the bottom. Dipstick removed
Drain plug removed Here’s the stainless hardware that’s included with the cover. They also include the two sizes of allen wrenches needed for the installation of the bolts and to service the drain plug/diptstick/sender port.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

2004-08 FORD F150 2WD & 4WD 2003-07 FORD EXPEDITION FRONT SPACER LIFT

Download steps 1. Jack the front of the vehicle in accordance to manufacture recommendation and support with jack stands, so the front two tires are off the ground. 2. Remove the two front tires/wheels. 3. Disconnect the sway bar end links at the top. 4. Disconnect the brake line from the strut tower. 5. Separate the upper ball joint from the spindle. Use a ball joint separator or other suitable tool. 6. Remove the 3 upper strut mounting nuts on the top off the strut tower. 7. Loosen the lower strut bolt and nut and push the upper control arm up and pull the strut toward you. 8. Apply the thread lock to the (3) strut studs and install the stud extenders and tighten down. 9. Install the spacer lift on top of the strut plate. 10. Push the upper control arm up and push the strut inward and place the jack under the lower control arm and jack up so the strut studs will go threw the strut tower, use the new lock nuts and washers to install the strut.… Read More

2004-Up AUXILLARY FORD INPUT ADAPTER INSTALLATION INSTRUCTION

Download What is an auxiliary input adapter ? An auxiliary input adapter is a vehicle specific device that connects to the radio’s CD Changer/DVD or Rear Seat Entertainment port and converts it to an audio input. With this auxiliary input installed you can connect and listen to any audio device (iPod, MP3, DVD, Sat Radio tuner etc) on the car speakers. The FRD04-AUX also features a built-in audio adjustment pot with 0 to +20dB input sensitivity range of 0.475 volts to 4.75 volts (peak to peak) which allows you to match the audio level of the Auxiliary device to that of the AM/FM Radio or CD. All Ford Compatible radios must have an “AUX” button and 16-pin “Phase II” radio connectors in the following vehicles: FORD LINCOLN 2007-08 Edge 2006-07 Mark LT 2007-08 Expedition 2007-07 MKX 2006-08 Explorer 2007-08 Navigator 2004 -08 F-150 2006 Zephyr 2005 -07 F-250 2005-07 F-350 2005-07 F-550 MERCURY 2005-08 Focus 2005-06 Montego 2005-0-7 Freestyle ² 2006-08 Milan 2005-06 Mustang 2006-08 Mountaineer 2007-08 Sport Trac.… Read More

2007 Toyota Camry Rear Bumper Removal and Replacement

Download REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.… Read More

INSTALLATION INSTRUCTIONS FOR PART 99-5812

DOWNLOAD APPLICATIONS FORD Edge 2007-2010 / Expedition 2007-2010 Explorer 2006-2010 / Explorer Sport Trac 2006-2010 F-150 2004-2008 / E Series 2009-10 / F Series 2005-2009 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2011 Mustang 2005-2009 / Super Duty 2008-2011 Taurus 2008 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2010 Sable 2008-2009 LINCOLN Mark LT 2005-2008. WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-5520 – Ford Harness 2003-up • 70-5521 – Ford Amplified Harness 2003-up • 70-5522 – Ford Sub Harness 2003-up • XSVI-5520 NAV – Ford Interface 2006-up Antenna Adapter: • 40-CR10 – Chrysler/GM Antenna Adapter 2002-up. DASH DISASSEMBLY FORD F-150 2004-2008 LINCOLN MARK LT 2005-2008 FORD EXPEDITION 2007-2010 FORD EDGE 2007-2010. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove entire panel surrounding the radio and climate controls. (Figure A) Remove (4) 9/32″ screws to remove the factory radio.… Read More

2000-2004 Ford Focus Rear Kit 75630 Installation Instructions

Download Always keep safety in mind when working on your vehicle. I. Preparing the Vehicle 1. Begin the installation by elevating the car. Secure the frame with jack stands (Figure 1). 2. Remove the rear wheels. 3. Remove the sway bar from the framerail and discard. II. Removing the Rear Suspension 1. Remove the lower shock bolt and retain. 2. Jack the vehicle up until the coil spring is loose enough to be removed (Figure 2). 3. Remove the bolts on both sides of the lower control arm and retain. 4. Remove the lower control arm and discard. III. Assembling the Air Spring Assembly 1. Place the air sleeve upper end cap to the under side of the mounting bracket (B) using two bolts (I), flat washers (L) and lock washers (J) (Figure 3). Torque to 25 ft/lbs. 2. Place the air fitting (K) onto the end of the sleeve. IV.… Read More

FORD, CHRYSLER, PONTIAC, OLDS WINDAGE TRAY INSTALLATION INSTRUCTIONS

Download To install studs : Remove a main bolt (main cap can be removed or left in place), tap threads, coat coarse threads with oil, screw stud in by hand, thread 2 main nuts on tray stud and lock them tightly together, lightly tighten tray stud 10-15 ft/lbs (making very sure that double nuts are not slipping or have run into the main cap), remove the 2 main nuts, coat the fine threads with oil, install the stud washer and nut, torque main stud with oil to torque spec of 65 ft/lbs for 7/16″ or 85 ft/lbs for 1/2″ studs, install 1 silver tray adjusting nut on the 3/8″ fine thread with the serrated face towards you (away from the engine). Do all the required studs locations to mount the tray in this fashion. You are now ready to mount the tray assembly. To install tray : Once all necessary tray studs have been installed properly, consult the special considerations section for the initial tray height and correct width, adjust the tray nut to this height, slide tray assembly into place and onto mounting studs, make sure that tray is supported equally by all studs (no wobble), the install the 2nd silver tray nut with the serrations toward the tray and torque with oil to 35 ft/lbs.… Read More