2004 chevy avalanche remove gas tank

You search Auto repair manual PDF about 2004 chevy avalanche remove gas tank, search results will appear below. If search results do not exist, please search by others keyword.

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Filed Under (Chevrolet (Chevy)) by admin on 29-12-2013

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

Kit Number 57-0662 Installation Instructions

Filed Under (Other Manuals) by admin on 02-01-2014

Download Citroen C4 1.6Hdi 2004-2009, Citroen Berlingo 1.6L 2005-2009, Citroen C2 1.6Hdi 2005-2009, Citroen C3 1.6Hdi 2008-2009, Citroen C3 Picasso 1.6Hdi 2009, Citroen C4 Picasso 1.6Hdi 2006-2009, Citroen C5 1.6Hdi 2005-2009, Mini Cooper 1.6Hdi 2007-2009, Mini Cooper Clubman 1.6Hdi 2007-2009, Peugeot 207 1.6 2006-2009, Peugeot 308 1.6 2007-2009, Peugeot 407 1.6 2005-2009, Peugeot Partner 1.6 2006-2009.
Parts list: 1 x Air filter Element. 1 x Silicone Intake Hose. 1 x Flexi Cold Air Hose. 1 x Metal Adaptor Hose. 1 x Literature Pack. Fixing Kit :- 3 x Plastic Tie. 3 x #44 Hose Clamp. 1 x Mounting Bracket. 1 x M6 Nylock Nut. 2 x M6 Flat Washer. 1 x Hex Head Bolt M6x20.
Instruction sheet A2054-768 1. Disconnect the negative terminal from the vehicle battery. 2. To the install induction kit it is necessary to remove the bulkhead trims: 3. Unclip & remove the side cover surrounding the washer bottle etc.… Read More

2001 Hyundai Accent Difficulty filling the gas tank. The pump keeps clicking off.

Filed Under (Hyundai) by admin on 02-04-2014

Download 2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Customer Concern: Difficulty filling the gas tank. The pump keeps clicking off. Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted.… Read More

2004 Audi A4 Fuel Pump Removing And Installing FWD

Filed Under (Audi) by admin on 07-01-2014

Download 2004 Audi A4 L4-1.8L Turbo (AMB) Vehicle Level Powertrain Management Fuel Delivery and Air Induction Fuel Pump Service and Repair Fuel Pump, Removing And Installing FWD. Removing And Installing Fuel Pump CAUTION: To remove the Fuel Pump (FP), the fuel tank may only be filled to a maximum of 3/4. Empty fuel tank if necessary. Recommended special tools and equipment 3087 wrench for tank sensor. VAS5190 fuel siphoning device Empty fuel tank Observe safety precautions. Observe rules for cleanliness. CAUTION: Observe safety precautions when disconnecting the battery. Disconnect battery Ground (GND) strap with the ignition switched off. CAUTION: Secure Ground (GND) wire of VAS5190 to a blank portion of the chassis. Pull cone piece -2- from shaft piece -1- of VAS 5190. Using insulating tape, apply a mark -arrow- on hose at length a = 1465 mm from end of suction hose. Remove fuel filler cap from fuel filler tube.… Read More

2004-2006 Acura TL Supercharger Installation Instructions

Filed Under (Acura) by admin on 10-12-2013

Download • Jack up and support the front of the car with jack stands. • Drain coolant from the radiator (make sure engine is cooled down). • Remove the plastic engine covers. • Remove the front bulkhead cover by removing the clips. • Make sure to keep all of the parts, they will be reused. The Comptech Supercharger comes complete with all parts shown in parts drawing. Please take a minute before starting installation and check that parts in box match “Supercharger Check List” provided in kit. Each blower kit is checked twice for completeness before leaving Comptech, but in case something was not included, please notify us before starting installation. Sales/technical support: 916.933.1080 3 Step #3 Intake/Throttle Body/Battery Removal: • Remove the upper air cleaner assembly (C ) by removing the (2) bolts (A) and disconnecting the clips (B). • Disconnect the battery cables, remove the battery hold down bracket and remove the battery.… Read More

2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 09-12-2013

Download FORD Edge 2007-2009 / Expedition 2007-2009 Explorer 2006-2009 / Explorer Sport Trac 2006-2009 F-150 2004-2008 / F Series 2005-2008 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2009 Mustang 2005-2009 / Super Duty 2008-2009 Taurus 2008-2009 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2009 Sable 2008-2009 LINCOLN Mark LT 2005-2009 Factory Navigation Only: MKX 2007-2009 / Navigator 2007-2009. DASH DISASSEMBLY A B C D E FORD MUSTANG 2005-2009 Remove the small rectangular shifter lever trim panel if equipped . (Figure A) 2 Remove (4) 9/32″screws from the radio to remove. (Figure E) 7 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (includingcup holders). (Figure B) 3 Unclip and remove panel. (Figure B) 4 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls.… Read More

2004 Chevrolet Chevy K Silverado Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More

2004 Acura TL GOLD EMBLEM INSTALLATION INSTRUCTIONS

Filed Under (Acura) by admin on 01-01-2014

Download Installing the Front “A” Emblem 1. Remove the two bolts that secure the left front bumper strake to the bottom of the front bumper and remove the bumper strake by sliding it sidewise. 2. Repeat step 1 to remove the right side bumper strake. 3. Remove the left side engine compartment cover (two pins and two tabs). 4. Remove the right side engine compartment cover (three pins and three tabs). 5. Open the engine hood. Remove the front bulkhead cover (three clips, two screw clips and two pins). 6. On each side fold down the front inner fender, and remove the front bumper (ten clips, two bolts and two self-tapping screws ). To prevent damage, set the bumper on a blanket during installation of the emblem. 7. Remove the center molding (five self-tapping screws). 8. Remove the two self-tapping screws that secure the existing “A” emblem and remove the emblem.… Read More

2002 Land Rover Freelander Camshaft Timing Belt Service Repair

Filed Under (Land Rover) by admin on 10-12-2013

Download Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated. Align Front Timing Belt. 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate.… Read More

You might also likeclose