2003 trailblazer cooler line replacement line

You search Auto repair manual PDF about 2003 trailblazer cooler line replacement line, search results will appear below. If search results do not exist, please search by others keyword.

1998 Chevrolet Blazer Engine Oil Cooler Hose/Pipe Replacement

Filed Under (Chevrolet (Chevy)) by admin on 12-03-2014

Download 1998 Chevrolet Blazer – 4WD | Blazer, Bravada, Jimmy, S10 Pickup, ┬áSonoma (VIN S/T) Service Manual | Engine | Engine Mechanical – 4.3L | Repair Instructions. Engine Oil Cooler Hose/Pipe Replacement (4WD) Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6.… Read More

2003 Chevy Truck TrailBlazer Service and Repair

Filed Under (Chevrolet (Chevy)) by admin on 16-02-2014

Download Transmission Oil Cooler Line Quick Connect Fitting Removal Procedure Important: The front and rear sections of the cooler lines can be serviced separately. Refer to the appropriate steps when servicing individual lines. Perform the following procedure when removing the cooler lines from the quick connect fittings. 1. Pull the plastic cap back from the quick connect fining and down along the cooler line about 5 cm (2 inch) . 2. Using a bent-tip screwdriver, pull on one of the open ends of the retaining ring in order to rotate the retaining ring around the quick connect fining until the retaining ring is out of position and can be completely removed. 3. Remove the retaining ring from the quick connect fitting. 4. Discard the retaining ring. 5. Pull the cooler line straight out from the quick connect fitting. Installation Procedure Important: * Do not reuse any of existing fittings if there is excessive corrosion.… Read More

2000 Buick Regal Oil Pan Replacement

Filed Under (Buick) by admin on 02-01-2014

Download Tools Required z J 28467-90A Engine Support Adapters z J 28467-B Universal Engine Support Fixture z J 36462-A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement . 4. Remove the drive belt. Refer to Drive Belt Replacement . 5. Install the J 28467-90A , the J 28467-B and the J 36462-A . Do not raise the engine. Refer to Engine Support Fixture . 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.… Read More

2003 Chevy Truck TrailBlazer Water Pump Replacement

Filed Under (Chevrolet (Chevy)) by admin on 26-12-2013

Download 1. Drain the coolant. 2. Remove the fan and shroud. 3. Remove the drive belt . 4. Using the J 41240, secure the water pump pulley and remove the water pump pulley bolts. 5. Remove the J 41240. 6. Remove the water pump pulley. 7. Loosen and remove the water pump bolts. 8. Remove the water pump. 9. Clean and inspect the water pump. 10. Discard and replace the gasket. Installation Procedure 1. Install a new water pump gasket. 2. Install the water pump and secure the water pump with the bolts. Tighten * On the initial pass, tighten the bolts to 4 Nm (35 lb in). * On the final pass, tighten the bolts to 10 Nm (89 lb in). 3. Install the water pump pulley. 4. Install the water pump pulley bolts. 5. Using the J 41240, secure the water pump pulley while tightening the water pump pulley bolts.… Read More

2003 Hyundai Tiburon Front Big Brake Kit Manual Installation Instructions

Filed Under (Hyundai) by admin on 21-11-2013

Download
Hyundai Tiburon Front Axle Kit. Kit Contents Your StopTech Big Brake kit includes the following: 1 pair of ST-40 four-piston calipers, sized specifically for your vehicle 1 set of high-performance street pads (not suitable for track use) 1 pair of 328 X 28mm two-piece rotor assemblies 1 pair of aluminum caliper adapter brackets 2 pair of 7/16-20 self-locking Jet nuts 2 pair of 12mm washers 1 pair of stainless steel brake lines 1 pair of banjo bolts 2 pair of copper crush washer s 1 pair of rubber end caps.
Step 1 Raise Vehicle, and Remove Wheels : A level, stable and clean surface, suitable for supporting the vehicle on jack-stands, should be used for the installation. For a front kit installation, apply the parking brake, then break loose the lug nuts on both front wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle.… Read More

2003 Chevy Truck TrailBlazer Cooling System-Electro-Viscous Fan Clutch Operation

Filed Under (Chevrolet (Chevy)) by admin on 07-04-2014

Download 2003 Chevy Truck TrailBlazer 2WD L6-4.2L VIN S Cooling System – Electro-Viscous Fan Clutch Operation. Subject: Operating Characteristics of the Electro-Viscous (EV) Fan Clutch and Diagnostic Tips for Cooling Fan Noise, Delayed Transmission Shifts and/or Engine Revving Too High Models: 2004-2006 Buick Rainier 2002-2006 Chevrolet TrailBlazer, TrailBlazer EXT 2006 Chevrolet TrailBlazer SS 2002-2006 GMC Envoy, Envoy XL 2004-2005 GMC Envoy XUV 2002-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.2L I-6, 5.3L V-8 or 6.0L V-8 Engine (VINs S, P, M, H – RPOs LL8, LM4, LH6, LS2) Date/VIN Breakpoints for Vehicles with New EV Fan Clutch. Vehicles built after and including the Date or VIN Breakpoints listed in the table shown are equipped with the new electro-viscous (EV) fan clutch . Vehicles of any model year listed in “Models Affected” with labor code J3390 (claimed after June 8, 2005) with P/N 15293048 in Claim History may also be equipped with this new EV fan clutch .… Read More

1994-2001 Acura Integra Edelbrock Intercooler Kits Installation Instructions

Filed Under (Acura) by admin on 10-12-2013

Download
DESCRIPTION: These high-efficiency intercoolers feature a bar and plate core with cast aluminum end tanks. Intercooler #15009 is designed for 1996-2000 Honda Civics, while #15036 is for 1992-1995 Honda Civics, and #15037 is designed for 1994-2001 Acura Integras. Modification of the stock bumper cover is required, aftermarket bumper covers may or may not need modification. Intercooler #15009 features a 22″long, 6″wide, 2.5″ thick core, while #15036 &15037 feature a 22″long, 5.5″wide, and 2.5″thick core. Hose connections for all intercoolers are 2.5″diameter.
INSTALLATION PROCEDURE
1. Installation of the intercooler requires removal of the front bumper cover. Follow your factory service manual for removal and reinstallation of the bumper cover. 2. For 1996-2000 Civic, remove the bolt holding the horn onto the center radiator support and move the horn to the side. On 1992- 1995 Civic and 1994-2001 Integra, the horn may need to be moved from it’s stock location. If necessary, drill and mount the horn using hardware of your choosing.… Read More

2003 Chevrolet Impala LS MULTIFUNCTION, TURN SIGNAL SWITCH REPLACEMENT

Filed Under (Chevrolet (Chevy)) by admin on 09-12-2013

Download Removal Procedure 1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR. 2. Remove the upper and lower trim covers. Refer to Steering Column Trim Covers Replacement . 3. Remove the wire harness assembly (1) from the wire harness strap (2). 4. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector. Fig. 29: Turn Signal & Multifunction Switch Assembly Connectors Courtesy of GENERAL MOTORS CORP. 5. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly out of the bulkhead connector (1). 6. Remove the 2 pan head tapping screws (1) and (3) from the turn signal and multifunction switch assembly (2). 7. Remove the turn signal and multifunction switch assembly (2) from the steering column tilt head assembly. Installation Procedure 1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.… Read More

2001 Hyundai Accent Difficulty filling the gas tank. The pump keeps clicking off.

Filed Under (Hyundai) by admin on 02-04-2014

Download 2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Customer Concern: Difficulty filling the gas tank. The pump keeps clicking off. Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted.… Read More

2004 Chevrolet Chevy K Silverado Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More

You might also likeclose