1982-2003 Ford Mustangs Double Hook Clutch Quadrant and Clutch Adjustment Kit INSTALLATION INSTRUCTIONS

Download DOUBLE HOOK QUADRANT INSTALLATION INSTRUCTIONS: STEP 1: At the bellhousing, remove the plastic splash shield. Use a pry-bar to slacken the clutch cable and disconnect it from the clutch fork. STEP 2: Under the dash, pull the end of the cable loose from the quadrant STEP 3: Under the dash there are two plastic parts that make up the factory clutch quadrant mechanism. They are held in place by clips on the end of the shafts. Remove the clips from the end of the shafts. STEP 4: Press the clutch pedal fully to the floor (you may have to pull the carpet aside) and pry the plastic quadrant and springs off. STEP 5: Press the clutch pedal to the floor again. Align the new aluminum quadrant with the shafts and slide the aluminum quadrant on. Center the quadrant in line with the hole where the cable comes through the firewall.… Read More

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

General Motors Accessories Headrest DVD System Display Monitor Inoperative

Download Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps.… Read More

Ford C-4 Bracket and Lever Installation Instructions

Download STEP 1. Raise and safely support the vehicle at least 1-2 feet off the ground. Remove the nut and lock- washer holding the downshift linkage onto the downshift lever shaft. The downshift lever is the outer lever on C-4 transmissions. Pull the lever off the shaft and allow the linkage to hang free. Remove and discard stock shift linkage rods. Late C-4 transmissions have a Neutral safety/Backup light switch on the transmission shift lever. If your transmission is so equipped, remove the two bolts holding the switch in place and slide it off the shift shaft. Disconnect the switch at the factory plug and discard it. STEP 2. Install the B&M selector lever, See figure 1 . Note: The B&M lever must point downward for proper operation. If the stock shift lever on your transmission points down, you will have to remove the lower part of the stock arm by cutting it off to clear the B&M lever, (See figure 1 ) .… Read More

Ford Focus Short SVT M-7210-S Throw Shifter INSTALLATION INSTRUCTIONS

Download REMOVING THE CONSOLE STEP 1: Remove the front cup holders. Remove the Torx screws under the cup holder with a T-20 bit. (Some cars may have Phillips head screws). STEP 2: Remove the rear cup holders. Squeeze the center and pull forward to undo the back tab, then pull straight up to unsnap the cup holder. Remove the nuts holding the rear of the console. STEP 3: Unscrew the shift knob from the shifter. Leave it attached to the leather boot. STEP 4: Pull the parking brake up as far as it will go. STEP 5: Pull up and back to remove the console. Be careful not to scrape the brake handle on the console. STEP 6: Reach underneath the console and disconnect the cigarette lighter plug. REMOVING THE STOCK SHIFTER STEP 7: Place the transmission in 1st gear. Steady the shift lever with one hand and pry the cable off with a screwdriver.… Read More

Various Concerns with Shifter and/or Ignition Key

Download Models: 2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) Condition Some customers may comment on any of the following concerns: Cause 1 The shifter button may be sticking in the handle. Cause 2 The pin that activates the micro-switch may have moved out of position (refer to illustration above). This causes the micro-switch to fail to engage when the vehicle is placed in Park. If this condition is present, the customer will not be able to remove the key from the ignition. The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter
assembly moves when activating the button.… Read More

1998 – 2000 NISSAN FRONTIER KA24 ENGINE

Download MIL WITH DTC P0400, P0402, ROUGH IDLE, DRIVABILITY INCIDENTS, DIFFICULTY SETTING EGR SRT. APPLIED VEHICLES: 1998 – 2000 Frontier (D22) with KA24 engine 2000 Xterra (WD22) with KA24 engine APPLIED ENGINE: KA24DE 4 cylinder engine IF YOU CONFIRM: • DTC P0400 (EGR) or P0402 (EGRC-BPT Valve) is stored in the ECM, and/or • The vehicle exhibits rough running or other drivability incidents, and/or • Difficulty in setting the EGR System Readiness Test (SRT) status to CMPLT. ACTION: Clean the intake manifold EGR ports. SERVICE PROCEDURE 1. Remove the throttle chamber assembly and place it aside. • Refer to the EM section of the appropriate Service Manual (ESM). NOTE: It is not necessary to completely remove the throttle chamber assembly. • Only remove harness connectors, cables, and hoses necessary to allow the throttle chamber assembly to be placed aside. • Throttle chamber coolant hoses do not need to be removed. 2.… Read More

2002-2004 Nissan Altima W/QR25 ENGINE; NO-START AFTER ‘COLD SOAK’

Download Altima; vehicles built up to 1N4AL11D(*)4C181189 Sentra; ALL APPLIED DATES: Altima; vehicles built up to 12-17-2003 Sentra; ALL IF YOU CONFIRM • After a ‘cold soak’,* the engine cranks (turns with starter), but does not start. *Cold soak: Engine has cooled down to ambient (outside) temperature, regardless of summer or winter seasonal variations. • The engine may start if it is cranked for an extended period (more than 5 seconds) or if the throttle is opened during cranking. • After starting and operating for a few minutes the engine runs normally. ACTIONS • Replace the starter motor. • Add 1 can of Nissan Fuel System Cleaner into the fuel tank. • Perform ECM Part Number Check to see if the vehicle you are working on needs ECM Reprogramming. • Perform ECM Reprogramming, if needed. IMPORTANT: The purpose of “ACTIONS” (above) is to give you a quick idea of the work you will be performing.… Read More

1990-1993 Acura Integra TWM Performance Short Throw Shifter Installation Manual

Download 1. Unscrew the stock shift knob by rotating it counter clockwise. 2. Remove all screws securing center console and remove console. 3. Remove the rubber dust boot surrounding the shifter, use caution not to damage it. Put it in a safe place for re-installation later. 4. Place the car up on a lift, or use a jack and jack stands to raise it off the ground. Loosen the nut on the base of the shifter using a 12mm socket and ratchet. You may need to hold the head of the bolt on the opposite side of the shift rod with a wrench to loosen the nut. 5. Remove the bolt from the base of the shifter and lower the shift rod that connected it to the shifter. 6. Remove both bolts securing the shift assembly to the under side of the chassis with a 12mm socket and ratchet. 7. Remove the bolt at the transmission end of the shift rod with a 12mm or 14mm (depending on model) socket and ratchet.… Read More

Honda Goldwing GL1200 Electronic Cruise Control Manual Installation

Download
1st step. The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The dual spool and carburettor cable are installed. The carburettor cable is attached to the lower groove in the dual spool. The other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location.… Read More