4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

1982-2003 Ford Mustangs Double Hook Clutch Quadrant and Clutch Adjustment Kit INSTALLATION INSTRUCTIONS

Download DOUBLE HOOK QUADRANT INSTALLATION INSTRUCTIONS: STEP 1: At the bellhousing, remove the plastic splash shield. Use a pry-bar to slacken the clutch cable and disconnect it from the clutch fork. STEP 2: Under the dash, pull the end of the cable loose from the quadrant STEP 3: Under the dash there are two plastic parts that make up the factory clutch quadrant mechanism. They are held in place by clips on the end of the shafts. Remove the clips from the end of the shafts. STEP 4: Press the clutch pedal fully to the floor (you may have to pull the carpet aside) and pry the plastic quadrant and springs off. STEP 5: Press the clutch pedal to the floor again. Align the new aluminum quadrant with the shafts and slide the aluminum quadrant on. Center the quadrant in line with the hole where the cable comes through the firewall.… Read More

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

2002 Jaguar X-Type Transmission Fluid Level Check

Download 2002 Jaguar X-Type V6-2.5L Vehicle Level Maintenance Fluids Fluid – A/T Testing and Inspection. Transmission Fluid Level Check Raise and support the vehicle. 1. Connect the approved Jaguar diagnostic system. 2. Make sure J-Gate shift selector is in the Park position (P). 3. With the engine running and the foot brake applied, move the J-Gate shift selector through “P-R-N-D-4-3-2″ and back to the “P” position to circulate the automatic transmission fluid until the temperature reaches 30 to 40°C (86 to 104°F) on the approved Jaguar diagnostic system. 4. When the automatic transmission fluid temperature reaches 35°C (95°F) check that the selector lever is in the “P. position raise the vehicle. Motor / ALLDATA Online – 2002 Jaguar X-Type V6-2.5L – Testing and… http://www.motoralldata.com/alldata/MOTOR~V71595976~C40438~… 2 of 4 3/28/2008 11:44 AM Zoom Sized for Print If the automatic transmission fluid does not come out of the transmission fluid level tube the automatic transmission fluid level is insufficient.… Read More

Checking oil level in automatic transmission and adding oil

Download TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 TRANSMISSION 722.750 /751 in MODEL 414.700. Adding transmission oil Risk of accident. Secure vehicle to prevent it from moving. AS00.00-Z-0005-01A Danger! Accidents may result if the vehicle starts off unintentionally with the Wear closed and snug-fitting work clothes. engine running. Risk of injury. Do not grasp hot or rotating parts. Crushing and burn injuries may result while working on engine during when it is being started or when it is in operation. 1 Remove locking pin (1) To do this, break off the plate on the locking pin using a suitable tool and press out the remaining pin in the cap downwards 2 Remove cap (2) 3 Fill with transmission oil The vehicle must be horizontal. Transmission oil (ATF) in accordance with BB00.40-P-0236-10A Specifications for Operating Fluids, sheet no.… Read More

MONSTER TRANSMISSIONS : FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Download
Please Note : The following instructions were made to act as a guide/reference, if you are inexperienced with performing an automatic transmission installation it is highly recommended that you contact a certified experienced professional to perform the installation and/or make the proper adjustments for you! Instructions : (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly!… Read More

1995 Ford Scorpio Transmission Range Sensor Installation Instructions

Download Remove 1. Move the selector lever to position “N”. 2. Raise the vehicle. 3. Unhook the loops for the rear exhaust pipe. 4. Detach the front heat shield and slide it backwards. 5. Detach the bracket for the front exhaust pipe from the transmission crossmember and swivel it downwards. NOTE: Support the automatic transmission with a transmission jack. 6. Detach the transmission crossmember. 1Detach it from the body. 2Detach it from the automatic transmission. Lower the automatic transmission and remove the transmission jack. 7. Detach the selector lever. 1Unclip the link rod from the selector lever. 2Selector lever 3Nut 4Selector shaft. 8. Disconnect the plug of the TR switch and remove the TR switch. Install NOTE: The guide of the TR switch must engage with the groove of the selector shaft. 9. Install and adjust the TR switch. NOTE: Do not tighten the bolts. 1Attach the TR switch. 2Slide on the selector lever and turn the selector shaft anti-clockwise as far as the stop.… Read More

2002 Dodge Truck RAM 2500 Truck AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING

Download 2002 Dodge Truck RAM 2500 Truck 4WD L6-5.9L DSL Turbo VIN 6 Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Testing and Inspection Symptom Related Diagnostic Procedures. 46RE AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING Before road testing, be sure the fluid level and control cable adjustments have been checked and adjusted if necessary. Verify that diagnostic trouble codes have been resolved.Observe engine performance during the road test. A poorly tuned engine will not allow accurate analysis of transmission operation. Operate the transmission in all gear ranges. Check for shift variations and engine flare, which indicates slippage. Note if shifts are harsh, spongy, delayed, early, or if part throttle downshifts are sensitive. Slippage indicated by engine flare, usually means clutch , band or overrunning clutch problems. If the condition is advanced, an overhaul will be necessary to restore normal operation. A slipping clutch or band can often be determined by comparing which internal units are applied in the various gear ranges.… Read More

1988-1991 Honda Civic BX2211 Installation Instructions

Download
Installation of this baseplate requires removing the two plastic belly pans and the vehicle’s tie down brackets. For CRX models, the air dam must also be removed and either permanently left off or cut. The plastic belly pans will be cut on all models. 1989 & Newer Honda Automatics All Honda and Acura automatic transmission vehicles, any model, any year, can be towed without special pumps or drive shaft disconnects. Please note however that Honda and Acura automatic transmissions for 1989 & newer were modified so they cannot be shifted rapidly from reverse to drive. Rapid shifting from reverse to drive can damage any automatic transmission. Honda advises that the modification leaves a portion of the automatic transmission in reverse when it is only shifted from reverse to neutral. This partial neutral condition cannot be detected by revving the engine, because the car will not move even though a portion of the transmission is still in reverse.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More