2004 Jeep Grand Cherokee Limited BODY & ACCESSORIES Speed Control

Download 1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL / INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks.… Read More

2003 Chevrolet Tahoe Test Details

Download  2002 Chevrolet Silverado 1500 4.8L, GAS, Vin V, Eng Cfg V8, USA/Canada 2003 Chevrolet Tahoe 4.8L, GAS, Vin V 2003 Chevrolet Silverado 1500 4.8L, GAS, Vin V, Eng Cfg V8 2003 Chevrolet Tahoe 5.3L, FLEX, Vin Z Customer Concern: The engine runs, but lacks power when driving. Has codes P0101 and P0300. Scanner shows misfires all on the same side of the engine. Tests/Procedures: 1. Check the catalytic converter, on the “suspect” bank of the engine, for a restricted (plugged) exhaust system to that side of the engine. 2. Disconnect both front O2 sensors, re-set the fuel trims and see if the problem goes away. 3. If gone with the O2 sensors disconnected, then swap the sensors side to side and see if the problem follows the O2 sensor. Potential Causes: Plugged Exhaust System Oxygen Sensor Diagnostic Codes: P0101, P0300 Author: Christopher Pittman Average Reported Mileage: 92479 Confirmed Fix Summary Confirmed Fix 9 – Catalytic Converter 1 – Exhaust System 1 – Intake Manifold Gasket(s) 1 – Right Catalytic Converter Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Phil Zeuner March 04, 2009 2003 Chevrolet Tahoe, 5.3L, FLEX, Vin Z Replaced Catalytic Converter – Replaced cat.… Read More

2003 BMW 325I Sport Wagon Check engine light on and fault codes stored

Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More

2005 Chevrolet Chevy K Silverado Panel Cluster Gauge Needle Function

Download Subject: 07187C — SPECIAL COVERAGE ADJUSTMENT – INSTRUMENT PANEL CLUSTER GAUGE NEEDLE FUNCTION Models: 2003-2004 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT 2005 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT (U.S. ONLY) 2003-2004 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE 2005 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE (U.S.ONLY) 2003-2004 GMC SIERRA, YUKON, YUKON XL 2005 GMC SIERRA, YUKON, YUKON XL (U.S. ONLY) Condition Some customers of all 2003-2004 model year and certain U.S. 2005 model year Cadillac Escalade, Escalade ESV, and Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, and Tahoe; and GMC Sierra, Yukon, and Yukon XL vehicles have reported that one or more of the instrument panel (IP) cluster gauges stick, flutter, or become inoperative. This may cause inaccurate readings, including the speedometer and fuel gauge. Special Coverage Adjustment This special coverage covers the condition described above for a period of 7 years or 70,000 miles (110,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership.… Read More

1997 Chevy Truck C Tahoe Interior Lighting Module Locations

Download 1997 Chevy Truck C Tahoe 2WD V8-5.7L VIN R View: Under Center Of Instrument Panel Zoom Sized for Print Interior Lamp Control Module, Remote Control Door Lock Receiver Manufacturer supplied 2 different possible locations. Look for 5 wire connector with wire colors: gray, white, orange, pink & black. #PIT3819: Location of Interior Lamp Control Module – keywords control dim dome electrical entry ground illumination inoperative keyless lens light remort resistor RKE short – (Dec 23, 2005) Subject: Location of Interior Lamp Control Module. Models: 1995-2000 Chevrolet C/K Trucks, Suburban and Tahoe 1995-2000 GMC Yukon and C/K Trucks Classic Body Style Only The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this P1. Condition/Concern When diagnosing a dome lamp concern on one of the vehicles listed above, you may be unable to locate the Interior Lamp Control Module that is called out in the Service Manual.… Read More

2005 Chevrolet Malibu Service and Repair

Download Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure 1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap.… Read More

2003 Chevy Truck TrailBlazer Cooling System-Electro-Viscous Fan Clutch Operation

Download 2003 Chevy Truck TrailBlazer 2WD L6-4.2L VIN S Cooling System – Electro-Viscous Fan Clutch Operation. Subject: Operating Characteristics of the Electro-Viscous (EV) Fan Clutch and Diagnostic Tips for Cooling Fan Noise, Delayed Transmission Shifts and/or Engine Revving Too High Models: 2004-2006 Buick Rainier 2002-2006 Chevrolet TrailBlazer, TrailBlazer EXT 2006 Chevrolet TrailBlazer SS 2002-2006 GMC Envoy, Envoy XL 2004-2005 GMC Envoy XUV 2002-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.2L I-6, 5.3L V-8 or 6.0L V-8 Engine (VINs S, P, M, H – RPOs LL8, LM4, LH6, LS2) Date/VIN Breakpoints for Vehicles with New EV Fan Clutch. Vehicles built after and including the Date or VIN Breakpoints listed in the table shown are equipped with the new electro-viscous (EV) fan clutch . Vehicles of any model year listed in “Models Affected” with labor code J3390 (claimed after June 8, 2005) with P/N 15293048 in Claim History may also be equipped with this new EV fan clutch .… Read More

2003 Chevy Truck TrailBlazer Service and Repair

Download Transmission Oil Cooler Line Quick Connect Fitting Removal Procedure Important: The front and rear sections of the cooler lines can be serviced separately. Refer to the appropriate steps when servicing individual lines. Perform the following procedure when removing the cooler lines from the quick connect fittings. 1. Pull the plastic cap back from the quick connect fining and down along the cooler line about 5 cm (2 inch) . 2. Using a bent-tip screwdriver, pull on one of the open ends of the retaining ring in order to rotate the retaining ring around the quick connect fining until the retaining ring is out of position and can be completely removed. 3. Remove the retaining ring from the quick connect fitting. 4. Discard the retaining ring. 5. Pull the cooler line straight out from the quick connect fitting. Installation Procedure Important: * Do not reuse any of existing fittings if there is excessive corrosion.… Read More

2003 Chevy Truck TrailBlazer Water Pump Replacement

Download 1. Drain the coolant. 2. Remove the fan and shroud. 3. Remove the drive belt . 4. Using the J 41240, secure the water pump pulley and remove the water pump pulley bolts. 5. Remove the J 41240. 6. Remove the water pump pulley. 7. Loosen and remove the water pump bolts. 8. Remove the water pump. 9. Clean and inspect the water pump. 10. Discard and replace the gasket. Installation Procedure 1. Install a new water pump gasket. 2. Install the water pump and secure the water pump with the bolts. Tighten * On the initial pass, tighten the bolts to 4 Nm (35 lb in). * On the final pass, tighten the bolts to 10 Nm (89 lb in). 3. Install the water pump pulley. 4. Install the water pump pulley bolts. 5. Using the J 41240, secure the water pump pulley while tightening the water pump pulley bolts.… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More