2002 town country ac diagram
You search Auto repair manual PDF about 2002 town country ac diagram
, search results will appear below. If search results do not exist, please search by others keyword.
Filed Under (Chrysler) by admin on 09-12-2013
DownloadModel(s): 1996-1999 Chrysler (NS) Town & Country 1996-1999 Dodge (NS) Caravan 1996-1999 Plymouth (NS) Voyager 1996-1999 Chrysler (GS) Voyager (International Market) Group: Cooling Bulletin No.: 07-02-99 Date: June 4, 1999 OVERVIEW This bulletin involves replacing the bracket that the idler pulley attaches to. SYMPTOM/CONDITION Loss of power steering assist and occurs when driving through deep snow or standing water. Snow or rain can enter the engine compartment from underneath the vehicle and force the serpentine belt off of the idler pulley. DIAGNOSIS Visually inspect the serpentine belt and idler pulley to determine if mis-alignment exists (If the serpentine belt is off the pulleys install the serpentine belt). Start the engine and let it run for one minute before checking alignment). The belt should be approximately 2mm (0.08 in.) from the inboard edge of the idler pulley ( Fig. 1 ) when alignment is correct and this bulletin does not apply. If the belt and pulley appear as in Fig.… Read More
Filed Under (Acura) by admin on 24-11-2013
Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More
Filed Under (Peugeot) by admin on 02-01-2014
ALARM/SIREN POSITION Position the compact alarms and the sirens on the dome of the shock absorber, passenger’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 3 mm2 RED wire located at the entrance of the fuse box. – 31: connect to one of the original ground terminals located on the right of the BSI operating central.. IGNITION WIRE + 15/54: connect to the wire at the position nr. 16 coming out of the 26 way blue connector of the BSI operating central. DIRECTION INDICATORS Connect to the wires at the positions nr. 13 and nr. 14 of the 16 way black connector coming out of the BSI operating central. ELECTRIC WINDOWS Positive control signal Front window, driver’s side: Refer to the diagram nr. 114. Front window, passenger’s side: Cut the 1 mm2 GREY wire located at the position nr.… Read More
Filed Under (Cadillac) by admin on 31-12-2013
Download 2002 Cadillac DeVille DHS V8-4.6L VIN Y Recall – Fuel Tank Pressure Sensor Malfunction. Product Safety – Fuel Tank Pressure Sensor # 03038A – (03/17/2004) 03038A — Fuel Tank Pressure Sensor 2002-2003 Cadillac DeVille, Seville Equipped with V8 (4.6L) Engine (LD8/L37) 2002-2003 Oldsmobile Aurora Equipped with V8 (4.0L) Engine (L47) 2002-2003 Pontiac Bonneville SSEi This bulletin is being revised to remove the parts restriction on the fuel tank and eliminate the need for the recall identification label. Please discard bulletin 03035, issued October 2003. Condition General Motors has decided that a defect which relates to motor vehicle safety exists in certain 2002-2003 model year Cadillac DeVille and Seville vehicles equipped with a V8 (4.6L) engine (LD8/L37), Oldsmobile Aurora vehicles equipped with a V8 (4.0L) engine (L47), and Pontiac Bonneville SSEi vehicles. The fuel tank pressure sensors in these vehicles are unusually susceptible to malfunctions. If the sensor malfunctions, excessive vacuum can be applied to the fuel tank during self-diagnostic testing.… Read More
Filed Under (Honda) by admin on 27-02-2014
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Filed Under (Acura) by admin on 29-03-2014
Download Honda Civic 2001-2002 Acura RSX 2002. Installation Instructions 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the wiring color guide. 3. Wire the 555I as shown in the wiring diagram. IMMOBILIZER IGNITION FEEDYELLOW/BLACK DATA RED/BLUE KEY SENSE RED/WHITE RED: Connect this wire to a constant (+)12 volt source. BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. BLUE: Connect this wire to the BLUE status output of the remote start. It must see ground during remote start. BLUE/WHITE: Connect this wire to the (-) key sense wire listed in the Wire Color Guide. It is located in a six-pin molex at the ignition cylinder. The key sense wire rests at ground when the key is inserted into the ignition switch.… Read More
Filed Under (Ford) by admin on 23-01-2014
Download FORD: MERCURY: 2002 EXPLORER 2002 MOUNTAINEER This article supersedes TSB 03-25-4 to update the 1. Loosen the intermediate band locknut on the description for labor operation “B”. There have been band adjustment screw. no changes made to the TSB procedure. 2. Using the special service tool (307-S022), tighten the suspect band adjustment screw to ISSUE 10 lb-ft (14 N•m). Some 2002 Explorer/Mountaineer vehicles built prior to 3/4/2002 with 5R55W transmission, may exhibit a. If the band adjustment torque cannot be no 3rd gear or slipping 2-3 shift with diagnostic achieved, both bands will need to be trouble codes (DTCs) P0733 and P0745 present. replaced. Proceed to PROCEDURE “B”. This may be due to a broken intermediate band. b. If the proper torque is achieved, the band is ACTION OK and does not need to be replaced. If the conditions described are verified: Proceed to Step 3 of PROCEDURE “A”. •Follow Service Procedure “A” to confirm band is 3.… Read More
Filed Under (Acura) by admin on 20-02-2014
Download Acura 2002-06 RSX Type-S L4-2.0L Honda 2002-05 Civic Si L4-2.0L . Part List : A Filtercharger 1 RU-4870 B Hose Clamp, #44 SS 3 08560 C Typhoon Intake Tube 1 27081 D Rubber Cap 1 08282 E Wave washer 1 08277 F 6mm Hex bolt, 16mm L. 1 07812 G Grommet 1 08283 H Hose Clamp, #004 1 21850 I Hose; 5/8″ID, 2-1/4″L, Rubber1 08692 J Silicone Hose black 1 08440 K Hose clamp, #10 mini 2 08411. 1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Loosen and remove the two bolts that secure the engine cover, then remove the engine cover as shown. 3. Using a pair of pliers, depress the hose clamp and slide it back off of the crank case vent on the air cleaner assembly as shown. 4. Using a pair of pliers, depress the hose clamp and remove the air temperature sensor from the stock intake tube as shown.… Read More
Filed Under (Infiniti) by admin on 03-02-2014
Download If a 2000 to 2002 G20 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed).… Read More
Filed Under (Acura) by admin on 10-12-2013
Download Models Honda Accord: 1999-2002 Honda Odyssey: 1999-2002 Honda Prelude 1999 Acura CL 2001-2002 Acura Integra: 2001-2002 Acura MDX: 2001-2002 Acura TL: 2001-2002. Installation Instructions 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide . 3. Wire the 555H as shown in the wiring diagram. Wire Color Guide SYNCH BLUE, ORANGE/BLUE, or BLUE/WHITE DATA RED OR BLUE/GREEN KEY SENSE BLUE/WHITE. Wire Connection Guide BLUE/WHITE: Connect this wire to the (-) key sense wire at the ignition cylinder. The key sense wire rests at ground when the key is inserted into the ignition switch. BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. BLUE: Connect this wire to the BLUE status output of the remote start.… Read More