Download 2001 Buick Regal V6-3.8L VIN K Vehicle Level Steering and Suspension Steering Power Steering Pump Service and Repair Power Steering Pump Replacement. Removal Procedure 1. Place a drain pan under the vehicle. 2. Remove the accessory drive belt. Refer to Drive Belt Replacement in Engine. 3. Raise and support the vehicle. Refer to Vehicle Lifting . 4. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. 5. Remove the power steering pressure hose from the power steering pump. Refer to Power Steering Pressure Hose Replacement. 6. Remove the power steering return hose from the power steering pump. Refer to Power Steering Return Hose Replacement. 7. Remove the power steering mounting bolts from the power steering pump. 8. Remove the power steering pump. 9. Remove the power steering pump reservoir from the power steering pump. 10. Transfer the power steering pump pulley. Refer to Power Steering Pulley Replacement Installation Procedure 1.… Read More
2002 Honda Odyssey Power Steering Pump Replacement
The car's Honda Odyssey Power Steering Pump employs hydraulic force to assist in turning your vehicle..
This is a detailed video of my procedure for replacing the power steering high pressure line on a 2002 Honda Odyssey. After developing a leak at 178,000.
On my 2005 Honda Odyssey, the power steering pump was leaking. It has about 96k miles on it. You will need a break over bar, 3/4" SAE short socket, several.
Filed Under (Ford) by Doe Namblas on 31-12-2013
Download 1993 Ford Escort G – TESTS W/CODES – EEC-IV (1.9L)’ ’1993 ENGINE PERFORMANCE Ford Motor Co. – Self-Diagnostics – EEC-IV. CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH) Diagnostic Aids When ignition switch is in the ON or START position, the PCM connects FUEL PUMP circuit (PCM terminal No. 22) to ground. The fuel pump relay is energized and electrical current flows to the fuel pump. If PCM does not receive ignition PIP signal within 2 seconds, FUEL PUMP circuit is opened and fuel pump operation is terminated. Perform this test when instructed by QUICK TEST or CIRCUIT TEST AA. This test is only intended to diagnose: * Fuel pump relay. * Inertia Fuel Shutoff (IFS) switch. * Wiring harness circuits (B+, VPWR, FUEL PUMP, GND and POWER-TO-PUMP). * Faulty Powertrain Control Module (PCM). Fig. 31: Fuel Pump Monitor Circuit Diagram (Escort & Tracer) 1)Code 87/556: Check VPWR To Fuel Pump Relay Code 87/556 indicates a fuel pump primary circuit failure.… Read More
Filed Under (Other Manuals) by Doe Namblas on 07-02-2014
Download Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville. Condition Some customers may comment on a steering vibration, shudder or moan noise when steering during parking maneuvers on dry pavement. Correction Install a new power steering pressure (inlet) hose assembly on the following vehicles: Install a new power steering pressure (inlet) and return (outlet) hose assembly on the following vehicles: Diagnosis Important: In diagnosing the above listed vehicles, do not overlook other obvious repairs prior to replacing the hose(s). 1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions.… Read More
Filed Under (Volkswagen (VW)) by Doe Namblas on 02-01-2014
Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More
Filed Under (Honda) by Doe Namblas on 02-02-2014
Download : 2001-02 Odyssey – ALL 2003 Odyssey – From VIN 5FNRL1…3B000001 thru 5FNRL1…3B159953 2003 Odyssey – From VIN 2HKRL1…3H500001 thru 2HKRL1…3H514354 2003 Pilot – From VIN 2HKYF1…3H500001 thru 2HKYF1…3H520648 Idle Fluctuation and/or the MIL Is On With DTC P1129 and/or P0505 (Supersedes 04-007, Idle Fluctuation With DTC P1129 , dated February 6, 2004, to update the information marked by the black bars) SYMPTOM The idle fluctuates, and/or the MIL is on with DTC P1129 (high manifold absolute pressure [MAP] sensor signal) and/or P0505 (faulty IAC valve). PROBABLE CAUSE The idle air control (IAC) valve sticks open, the power steering pressure switch wire is broken, or both. CORRECTIVE ACTION Replace the IAC valve, repair the power steering pressure switch wire, or do both. DIAGNOSIS 1. Start the engine, and let it idle until it warms up. Does the idle fluctuate, or is there a customer complaint of an intermittent idle fluctuation?… Read More
Filed Under (Ford) by Doe Namblas on 31-12-2013
Download 2.0L FORD FOCUS Supercharger System Installation Instructions 2000-2003 ZX3 Model 2002-2003 SVT Model. A. Remove the ducting between the air box and the throttle body. Disconnect the MAF from the ducting and set aside. B. Remove the air box, fresh air tube, battery, battery box and all remaining components running to the inlet of the motor. C. Remove the Battery/Air Box support bracket: 1. Support the driver’s side of the transmis- sion. 2. Remove four nuts securing the bracket to the driver’s side engine mount. 3. Remove the large central nut securing the transmission to the engine mount. 4. Lift the plate on top of the engine mount and remove the Battery/Air Box support bracket. (See Fig. 1-a .) 5 . Reinstall the engine mount plate and resecure all engine mount hardware. D. Place an oil drain pan beneath the power steering pump. Disconnect the high-pressure (3/8″ tube) power steering line from the power steering pump.… Read More
Filed Under (Honda) by Doe Namblas on 30-12-2013
Download SYMPTOM A screech or whine from the rear differential when making a tight turn at low speed (for example, in a parking lot when 4WD engages). PROBABLE CAUSE The differential fluid is contaminated or broken down, providing insufficient lubrication. CORRECTIVE ACTION Replace the dual pump fluid, and test-drive the vehicle. If necessary, replace the rear differential clutch, replace the oil pump assembly (1997 model only), and add a flow collar. PARTS INFORMATION Flow Collar Kit: P/N 41431-P6R-000, H/C 6839724 Differential Clutch Set: P/N 48010-P6R-305, H/C 6627566 Oil Pump Set (1997 model only): P/N 48100-P1D-305, H/C 6839716 REQUIRED MATERIALS Dual Pump Fluid: P/N 08200-9002, H/C 6512644 Liquid Gasket (Hondabond HT): P/N 08718-0001, H/C 2963817. REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type.… Read More
Filed Under (Acura) by Doe Namblas on 24-11-2013
Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More
Download Tools Required z J 28467-90A Engine Support Adapters z J 28467-B Universal Engine Support Fixture z J 36462-A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement . 4. Remove the drive belt. Refer to Drive Belt Replacement . 5. Install the J 28467-90A , the J 28467-B and the J 36462-A . Do not raise the engine. Refer to Engine Support Fixture . 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.… Read More
Filed Under (Chrysler) by Doe Namblas on 19-01-2014
Download TROUBLE SHOOTING Inspect power window circuit breaker (25-amp), located in left kick panel. Inspect fuse No. 28 (40-amp) in Intelligent Power Module (IPM). IPM is located on left side of engine compartment. Inspect ground at right “B” pillar. SYSTEM TESTS ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay.… Read More