2002 cadilac deville leaking water under coolant reservoir

You search Auto repair manual PDF about 2002 cadilac deville leaking water under coolant reservoir, search results will appear below. If search results do not exist, please search by others keyword.

2002 Ford Escort Cooling System Draining, Filling and Bleeding Workshop Manual

Filed Under (Ford) by admin on 25-01-2014

Download Draining 1. Bring the engine to normal operating temperature and turn the engine off. With the cooling system under pressure, inspect cooling system hoses and clamped hose connections for leaks, excessive deterioration or contact wear. Inspect radiator installation retention. Note any discrepancies and proceed. 2. WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap.… Read More

1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

Filed Under (Saturn) by admin on 24-02-2014

Download 1999 Saturn SL1 L4-1.9L SOHC VIN 8 Vehicle Level Powertrain Management Computers and Control Systems Coolant Temperature Sensor/Switch (For Computer) Technical Service Bulletins All Technical Service Bulletins Engine – Driveability Concerns/Cooling System DTC’s Set. SUBJECT: Engine Coolant Temperature Sensor Related Diagnostic Trouble Code(s) and/or the Following Conditions: Hard Start, Erratic Idle, Rough Running. Engine Overheating, Low and/or Leaking Coolant, and/or Service Engine Soon Lamp Illuminated. (Replace Engine Coolant Temperature Sensor with New Design Sensor- P/N 21025106) MODELS AFFECTED: 1991-2001 Saturn S-Series vehicles CONDITION: Customers may comment about various driveability and/or engine operating concerns including: hard start, erratic idle, rough running, engine overheating, low and/or leaking coolant, and/or Service Engine Soon lamp illuminated. CAUSE: This condition may be caused by a cracked engine coolant temperature sensor. CORRECTION: Replace engine coolant temperature sensor, inspect and if necessary replace sensor harness connector. Refer to procedure in this bulletin to replace engine coolant temperature sensor and Parts Requirements for specific parts information.… Read More

2002 Cadillac DeVille DHS V8-4.6L VIN Y

Filed Under (Cadillac) by admin on 31-12-2013

Download 2002 Cadillac DeVille DHS V8-4.6L VIN Y Recall – Fuel Tank Pressure Sensor Malfunction. Product Safety – Fuel Tank Pressure Sensor # 03038A – (03/17/2004) 03038A — Fuel Tank Pressure Sensor 2002-2003 Cadillac DeVille, Seville Equipped with V8 (4.6L) Engine (LD8/L37) 2002-2003 Oldsmobile Aurora Equipped with V8 (4.0L) Engine (L47) 2002-2003 Pontiac Bonneville SSEi This bulletin is being revised to remove the parts restriction on the fuel tank and eliminate the need for the recall identification label. Please discard bulletin 03035, issued October 2003. Condition General Motors has decided that a defect which relates to motor vehicle safety exists in certain 2002-2003 model year Cadillac DeVille and Seville vehicles equipped with a V8 (4.6L) engine (LD8/L37), Oldsmobile Aurora vehicles equipped with a V8 (4.0L) engine (L47), and Pontiac Bonneville SSEi vehicles. The fuel tank pressure sensors in these vehicles are unusually susceptible to malfunctions. If the sensor malfunctions, excessive vacuum can be applied to the fuel tank during self-diagnostic testing.… Read More

2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT

Filed Under (Pontiac) by admin on 21-01-2014

Download 2002 Pontiac Grand Prix GT 2002 ENGINE Engine Cooling – Grand Prix THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces. Installation Procedure 1. Install the thermostat. 2. Install the water outlet gasket and the water outlet housing. 3. Install the water outlet housing bolts.… Read More

2004 Jeep Grand Cherokee Limited BODY & ACCESSORIES Speed Control

Filed Under (Other Manuals) by admin on 30-11-2013

Download 1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL / INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks.… Read More

2002 Audi TT Timing Belt Replacement

Filed Under (Audi) by admin on 03-04-2014

Download Tools recommended include: Bentley Publishers Audi TT Service Manual (book or CD), Torque Wrench (3/8″ drive recommended), Floor Jacks (2 minimum), Jack Stands (3 minimum), Tool Set including ratchet / extensions / wrenches / metric sockets (various lengths) / hex bit sockets / torx drivers / Allen wrenches (hex key), Wheel Chocks (2), Small Clamps, and a digital camera to document your progress in case you need to go back and review how it was originally installed. Supplies recommended include: 3 Liters of VW/Audi G-012 Coolant Antifreeze, 3 Liters of Distilled Water, ½ – gallon size clear plastic pitcher (for mixing Distilled Water and Coolant), 1 Liter of VW/Audi G-004 Power Steering Fluid (a lot less is needed), Loctite high temperature Threadlocker, Bucket & Hose to drain coolant (hose ID approximately 10mm), Shop Towels/Rags, Plastic Bags, Zip Ties, Rubber Stoppers (to plug coolant and power steering hoses), Marking Pen (Red China Marker), and an Abrasive Pad (ScotchBrite).… Read More

2002 Ford Taurus WATER IN THE BLOWER CASE

Filed Under (Ford) by admin on 09-12-2013

Download FORD: 2001-2004 Taurus MERCURY: 2001-2004 Sable This article supersedes TSB 03-15-06 to update the vehicle model years and build date information. ISSUE Some vehicles built between 5/1/2001 and 12/15/2003 may exhibit water in the blower case or on the passenger side floor, an inoperative climate control blower motor , a motor that operates on high speed only, and/or a blower motor resistor failure. ACTION Inspect and seal cowl area and install Rain-Hat Extension Seal. Inspect and replace blower motor and/or blower motor resistor if there is evidence of water/corrosion. Refer to the following Service Procedure for details. SERVICE PROCEDURE 1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z- 19805-AA and resistor F6DZ-19A706-AA). 2. Visually inspect the Cowl Vent Screen located under the RH windshield wiper to verify if the screen is fully seated.… Read More

FORD DIESEL ENGINES Hydronic5 Espar Heater System Installation, Troubleshooting, Repair Manual

Filed Under (Peugeot) by admin on 03-03-2014

Download
HYDRONIC 5 for FORD DIESELENGINES Heater Model 25 1920 05 Installs are for models 250/350 4 wheel drive & 4 wheel ABS 2 wheel drive & 4 wheel ABS. Heater Warnings to Installer •Correct installation of this heater is necessary to ensure safe and proper operation. Read and understand this manual before attempting to install the heater. Failure to follow all these instructions could cause serious or fatal injury Explosion Hazard •Heater must be turned off while re-fueling. •Do not install heater in enclosed areas where combustible fumes may be present. Fire Hazard •Install the exhaust system so it will maintain a minimum distance of 50mm(2″) from any flammable or heat sensitive material. •Ensure that the fuel system is intact and there are no leaks. Asphyxiation Hazard •Route the heater exhaust so that exhaust fumes cannot enter any passenger compartments. •If running exhaust components through an enclosed compartment, ensure that it is vented to the outside.… Read More

2003 Chevy Truck TrailBlazer Water Pump Replacement

Filed Under (Chevrolet (Chevy)) by admin on 26-12-2013

Download 1. Drain the coolant. 2. Remove the fan and shroud. 3. Remove the drive belt . 4. Using the J 41240, secure the water pump pulley and remove the water pump pulley bolts. 5. Remove the J 41240. 6. Remove the water pump pulley. 7. Loosen and remove the water pump bolts. 8. Remove the water pump. 9. Clean and inspect the water pump. 10. Discard and replace the gasket. Installation Procedure 1. Install a new water pump gasket. 2. Install the water pump and secure the water pump with the bolts. Tighten * On the initial pass, tighten the bolts to 4 Nm (35 lb in). * On the final pass, tighten the bolts to 10 Nm (89 lb in). 3. Install the water pump pulley. 4. Install the water pump pulley bolts. 5. Using the J 41240, secure the water pump pulley while tightening the water pump pulley bolts.… Read More

1995 Nissan-Datsun Maxima Water Pump: Service and Repair

Filed Under (Nissan) by admin on 09-12-2013

Download When removing water pump assembly, be careful not to get coolant on drive belt. Water pump cannot be disassembled and should be replaced as a unit. After Installing water pump, connect hose and clamp securely, then check for leaks using radiator cap tester. 1.Drain coolant from drain plugs on radiator and both sides of cylinder block. 2.Remove drain plug on cylinder block. 3.Remove right side engine mounting, mounting bracket and nuts. 4.Remove drive belts and idler pulley bracket. 5.Remove chain tensioner cover and water pump cover. 6.Pushing timing chain tensioner sleeve, apply a stopper pin so it does not return. Then remove the chain tensioner assembly. 7.Remove the 3 water pump fixing bolts. Secure a gap between water pump gear and timing chain, by turning crankshaft pulley 2O° backwards. 8.Put M8 bolts to two M8-threaded holes out of 3 water pump fixing bolt holes. 9.Tighten M8 bolts by turning half turn alternately until they reach timing chain rear case.… Read More

You might also likeclose