2003 BMW 325I Sport Wagon Check engine light on and fault codes stored

Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More

2002-2003 Acura RSX Icebox Cold Air Intake Installation Instructions

Download Honda Civic Si & Acura RSX Icebox Cold Air Intake Installation Instructions (2002-2003 Honda Civic Si) (2002-2003 Acura RSX—All) Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan. •Remove ground strap bracket on side of transmission (C). Relocate ground strap from transmission bracket to top of transmission (D). Step #2 Install Comptech Airbox •Install (3) stock rubber grommets* (E) through large holes on underside of mounting ears on Icebox (a small dab of filter oil may be used to ease this process).… Read More

2000-2003 Ford Focus 2.0L Zetec 21-450 COLD AIR SYSTEM Installation Instructions

Download The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot underhood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some models and years still pending) and come with complete instructions for ease of installation. Read and understand these instructions BEFORE attempting to install this product. 1) Getting started a) Make sure vehicle is parked on a level surface.… Read More

2002 – 2003 Honda Civic Si & Acura RSX Comptech Icebox Cold Air Intake Installation Instructions

Download Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX). Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

2000-2002 Audi TT Part RD3025p Cold Air Intake System

Download Note: Disconnect the negative battery terminal before starting this installation. 1. Remove the air intake box and air intake duct that leads to the mass air flow sensor. 2. Slip the 2 3/4″ straight hose over the mass air flow sensor use two clamps and tighten the clamp on the mass air flow sensor. (See fig. 2) 3. Take the vibra-mount and screw it into the bracket located on the side of the strut tower mount. (See fig. 3) Removing the head lamp and the front bumper. 4. Remove the 3 m6 bolts located on the extended plastic arms on the head lamp. (See fig. 4) You will also disconnect the three harness clips located on the back side of the head lamp. (See fig. 5) 5. In order to remove the bumper you need to peel back the splash guards in the wheel well. Unscrew two m6 nuts on each side of the frame located behind the splash guards.… Read More

i-BMW-T DICE iPod Integration Kit

Download If vehicle has DSP, please see BMW-DSP supplement in addition to this guide. Models Supported: AUX Audio Source: MP3, DVD, TV… DICE Module iPod Vehicle (CD changer/SAT Port) BMW 3-Series 96-05 i-BMW-T BMW Standard/Business 5-Series 97-03 7-Series 9/98-01 X3 04-06 X5 00-06 1 *All BMW vehicles MUST be pre-wired for factory CD changer. 1 – Cars with OEM Sirius require BMW SAT harness. DSP requires additional DSP module. Z4 03-06 M-Roadster 99-02 Z3 96-02 M-Coupe 99-02 M3 96-06 M5 00-03 Z8 00-03 1(except ’96 318ti) 1 1 1 1 1 1 1 1 1 1 BMW Standard/Business BMW Standard/Business BMW Standard/Business BMW Standard/Business BMW Standard/Business BMW Standard/Business BMW Standard/Business BMW Standard/Business BMW Standard/Business BMW Standard/Business BMW Standard/Business i-BMW-T i-BMW-T i-BMW-T i-BMW-T i-BMW-T i-BMW-T i-BMW-T i-BMW-T i-BMW-T i-BMW-T i-BMW-T Installation Instructions: 1. Pull vehicle into service bay and access trunk area. 2. Open Trunk and access boot area. 3. Disconnect both battery terminals.… Read More

2001 Volkswagen Jetta GLS Relay Panel

Download Thirteenfold Auxiliary Relay Panel. Relay location on the thirteen position auxiliary relay panel, above relay panel: Relay Panel: Relay Panel & Thirteenfold Auxiliary Relay Panel Zoom Sized for Print 1 -Auxiliary Emergency Flasher Relay (404) 2 -Relay for Motor Remote Unlock Rear Lid (79) 3 -Starting Interlock Relay (53) (185) (465) 4 -Fog Light Relay (53) 5 -Control Module for Multi-function Steering Wheel (450) 6 -Control Module for Multi-function Steering Wheel (450) 7 -Daytime Running Lights Change-over Relay (173), from April 1999 8 -Daytime Running Lights Change-over Relay (173), through March 1999 9 -Dual Horn Auxiliary Relay (53) 10-Glow Plug Relay (180) 10-Warning Lamp Auxiliary Relay (200) 11-Park/Neutral Position (PNP) Relay (175) 12-Power Supply (Terminal 30, B+) Relay (109) 1 -Dual Horn Relay (53) 2 -Load Reduction Relay (18) (100) 4 -Fuel Pump (FP) Relay (409) V -Wiper/Washer Intermittent Relay (192) (377) (389) VI -Wiper/Washer Intermittent Relay (192) (377) (389) NOTE Number in parentheses ( ) indicates production control number stamped on relay housing.… Read More

1998 Dodge Truck Caravan Replace Radiator Fan Relay

Download 1. With the ignition key in the OFF position, disconnect the battery. 2. Remove the two (2) screws that attach the air inlet resonator to the upper radiator support. 3. Disconnect the upper and lower air inlet hoses from the resonator and remove the resonator. 4. Remove the air cleaner housing. 5. Locate the radiator cooling fan relay on the left front inner frame rail just behind the radiator (Figure 1). 6. Disconnect the radiator fan relay wiring connector. 7. Remove the radiator fan relay. Discard the relay and the attaching screws. 8. Install the new radiator fan relay using the supplied screws. Tighten the screws to 35 in-lbs (4 N.m). CAUTION: Do not over torque screws. To ensure heat transfer and proper operation, the new radiator fan relay must be installed using both of the provided screws. 9. Connect the radiator fan relay electrical connector. Slide the red latch to the locked position.… Read More

1997-2002 FORD EXPEDITION REPEAT AIR SUSPENSION COMPRESSOR DRIER FAILURES

Download Some 1997-2002 Expedition 4X4 and 1998-2002 COMPONENTS AS HIGH PRESSURE IS VENTED Navigator 4X4 vehicles equipped with 4-wheel air UNCONTROLLED. suspension, may exhibit repeat air compressor drier If diagnostics lead to compressor/dryer assembly failures. The drier cap may become detached from replacement, use the following service procedure to the drier body, or the drier body may be broken at insure complete and thorough service. the neck near the compressor head. This may be due to incomplete or incorrect system diagnosis that 1. Using the New Generation STAR (NGS) tester, leads to replacement of only the original air vent the compressor/drier assembly. suspension compressor, despite the fact that the compressor is not the root cause of the concern. 2. Using regulated shop air, blow out the air lines Compressor failure in these instances is only a from the drier to the front fill solenoid valve, symptom of an underlying system problem.… Read More

1995 Ford Scorpio Fuel Injection Pump Installation Instructions

Download Remove CAUTION: Disconnect the battery negative lead. MPS2305120 1. Disconnect the vent pipe from the air cleaner outlet tube. 2. Disconnect the air cleaner outlet tube from the turbocharger compressor intake pipe (one clip). MPS2305122 3. Remove the air cleaner outlet tube retaining band. MPS2305123 4. Remove the air cleaner outlet tube. DTS2305156 Vehicles fitted with air conditioning 5. Disconnect the air conditioning clutch multiplug. CAUTION: When removing the retaining bolts, support the air conditioning compressor to prevent damage. 6. Remove the three air conditioning compressor retaining bolts. DTS2305158 CAUTION: When positioning the air conditioning compressor to one side do not put any strain on the air conditioning pipes. 7. Using a piece of heavy wire, secure the air conditioning compressor to one side. TIS2305024 Vehicles without air conditioning 8. Remove the alternator drive belt idler pulley. MPS2305124 All vehicles NOTE: When removing the blanking plug ensure that the sealing washer is recovered.… Read More