2005 Ford Mustang GT Roush Fog Lamp Wiring Harness Installation Instructions

Download 1. SAFETY REQUIREMENTS STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation. 1. Always wear safety glasses for eye protection. 2. Place ignition switch in the OFF position. 3. Always apply the parking brake when working on a vehicle. 4. Block the front and rear tire surface to prevent unexpected vehicle movement. 5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. 6. Do not smoke or use flammable items near or around the fuel system. 7. Use chemicals and cleaners in well-ventilated areas. 8. Batteries produce explosive gases, which can cause personal injury.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

1998 – 2001 Ford Explorer 4WD Ford Ranger Explorer Sport Trac / Edge Mountaineer 4WD Torsion bar key front leveling kit

Download Part # 22907 1998 – 2001 Ford Explorer 4WD 1998 – 2007 Ford Ranger / Explorer Sport Trac Edge / Mountaineer 4WD Torsion bar key front leveling kit Part# Description Qty. 22907-01 Torsion bar keys 2 22907INST Instruction manual (customer copy) 1 22907INST Instruction manual (installer copy) 1 WARNINGDECAL Warning decal 1 MIRRORHANGER Rear view mirror hanger 1. Important customer information: Tuff Country EZ-Ride Suspension highly recommends that a qualified and/or certified mechanic performs this installation. If you desire to return your vehicle to stock, it is the customers responsibility to save all stock hardware. This vehicles reaction and handling characteristics may differ from standard cars and/or trucks. Modifications to improve and/or enhance off road performance may raise the intended center of gravity. Extreme caution must be utilized when encountering driving conditions which may cause vehicle imbalance or loss of control. DRIVE SAFELY! Avoid abrupt maneuvers, such as sudden sharp turns which could cause a roll over, resulting in serious injury or death.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

2005 2.0L Ford Focus Saleen Speedlab AFTERMARKET NITROUS KIT INSTALLATION MANUAL

Download The 2.3-Liter Focus Nitrous Kit contains everything you need to bring your 2003 ½ through 2004 Focus from a stock car to a performance vehicle with full nitrous capabilities. This manual contains all the basic instructions for installing the kit and some helpful advice to ensure safe nitrous use. Please be advised that installing this kit will void any and all Ford powertrain warranties for the vehicle. Obtain the following parts: 05-1904-B09710* SALEEN NITROUS KIT 2005 FOCUS 1 05-1602-C08045 BRACKET N2O SOLENOID 1 00-9001-C00225* Installation Instructions 1. Using the standard Ford stereo removal tool, remove the stereo. 2. Unscrew A/C controls, take out ashtray, disconnect wiring harnesses, and set trim piece aside. Note where each wiring harness goes. 3. Measure 1 5/16″ down from the top of the audio unit trim, and 1 1/8″ in from the driver side of the trim. Drill a hole 3/4″ in diameter for nitrous switch.… Read More

2001 Ford Mustang BRAKES Disc & Drum – Cars – Except Contour, Escort, Focus, LS & Mystique Installation

Download REAR BRAKE CALIPER CAUTION: Components are not interchangeable from side to side. Disassembly (Continental, Cougar, Mustang, Sable &Taurus) 1. Remove caliper. See REARBRAKE CALIPER &PADS under REMOVAL&INSTALLATION. Mount caliper in a soft-jawed vise. Using Piston Remover/Installer (T87P-2588-A), rotate piston counterclockwise and remove piston from bore. See Fig 13 . Remove dust boot and seal from bore. 2. Carefully remove snap ring, as snap ring and spring cover are under spring load. Remove spring cover, spring, flat washer and key plate. Pull push rod and strut pin from bore. Discard “O”ring from push rod. 3. Remove parking brake lever return spring. Remove lever bolt, and pull lever out of housing. Remove and discard seal. Inspection Clean all metal parts with isopropyl alcohol and dry with compressed air. Replace components if worn, pitted or scored. Reassembly 1. Apply a light coat of Silicone Dielectric Compound (D7AZ-19A331-A) to parking brake lever shaft, bore &seal.… Read More

2000-2001 FORD FOCUS 4DR W-TYPBODYKIT INSTALLATION INSTRUCTIONS

Download 1) front air dam remove one torx bit screw in each wheel well (front) that secures the inner fender well. Replace it with the 1- 1/12″ screw supplied. Check fit the front air dam on the original bumper, after it is properly aligned, using a grease pencil, draw a line along the top edge of the part to be used as a reference in final installation. Using a paper towel with grease remover, or lacquer thinner, thoroughly clean the area on car where the double face tape will come in contact with the painted surface. Do not allow thinner or cloth to remain on car too long as it can cause damage to the painted surface. Using the recommended adhesion promoter, on a clean lint-free cloth, apply a thin uniform coating to the bonding surface, allow promoter to dry thoroughly before attempting installation of the part. Carefully peel approximately 2″ of plastic backing from tape, making a “tail” from center of air dam so that you can position part on car with backing still on tape.… Read More

2008-2010 FORD FOCUS ELECTRONIC CRUISE KIT 250-1840

Download 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting. Figure 1 2. Remove the driver side lower dash and kick panels. Remove the steering wheel shroud. Figure 2 B. Install Electronic Module 1. Plug in the Main Wiring Harness, Switch Harness, and Pedal Interface Harness onto mating connectors of the Cruise Control Module. Figure 3 2. Place the Cruise Control Module in a secure location behind the driver side dash area near the firewall away from moving parts. Secure with supplied wire ties. 3. Route the Pedal Interface Harness through steering column and down to the accelerator. 4. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of Pedal Interface Harness. Apply the other connector to the accelerator.… Read More

COMP Cams® Ford Timing Set Installation Instructions

Download Ford Timing Set Installation Instructions Thank you for choosing COMP Cams® products! We know you have options in valve train component selection and we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to review the included limited warranty information. Engine Application High Energy Magnum Hi-Tech Ford V6, 144-200 3223 Ford V6, 171 (2600-2800cc) 3236 Ford V8, 255, 289, 302 & Boss 302, 1965-1988 2120 3120 Ford V8, 289-351W & Boss 302, pre 1972 3220 Ford V8, 302-351W, 1972 & up 3230 Ford V8, 352-428, 1964-1974 3208 2108 3108 Ford V8, 351C, 351M, 400M, 1970-1982 3221 2121 3121 Ford V8, 429-460, 1968-1971 3222 2122 3122 Ford V8, 429-460, 1972-1987 2130 3130 Ford V8, 429-460 w/nine keyway crank gear 2134* Ford V8, 351W, 351W H.O., 1969-¹84 2135 3135 Ford V8, 5.0L 302 H.O., 1980-March 21, 1984 2131 3131 Ford V8, 5.0L 302, 351W, March 22, 1984-1992 2138 3138 Notes: * #2120 or #3120 should not be installed on 351W engines as they are designed for 255, 289, 302 or Boss 302 engines.… Read More