Download The transmission solenoid/TRS assembly is internal to the transmission and mounted on the valve body assembly. The assembly consists of six solenoids that control hydraulic pressure to the six friction elements (transmission clutches), and the torque converter clutch. The pressure control solenoid is located on the side of the solenoid/TRS assembly. The solenoid/TRS assembly also contains five pressure switches that feed information to the TCM. OPERATION SOLENOIDS Solenoids are used to control the L/R, 2C, 4C, OD, and UD friction elements. The reverse clutch is controlled by line pressure and the position of the manual valve in the valve body. All the solenoids are contained within the Solenoid and Pressure Switch Assembly. The solenoid and pressure switch assembly contains one additional solenoid, Multi-Select (MS), which serves primarily to provide 2nd and 3rd gear limp-in operation. The solenoids receive electrical power from the Transmission Control Relay through a single wire. The TCM energizes or operates the solenoids individually by grounding the return wire of the solenoid as necessary.… Read More
2001 Dodge Ram 2500 Shift Solenoid
Get the Best Priced Dodge Ram 2500 Automatic Transmission Solenoid.
Get the Best Priced Dodge Ram 1500 Automatic Transmission Solenoid.
Find great deals on eBay for 2001 dodge ram 1500 transmission 2001 dodge ram 1500 4x4 transmission. Shop with confidence..
Filed Under (Dodge) by Doe Namblas on 01-01-2014
Download 2002 Dodge Truck RAM 2500 Truck 4WD L6-5.9L DSL Turbo VIN 6 Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Testing and Inspection Symptom Related Diagnostic Procedures. 46RE AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING Before road testing, be sure the fluid level and control cable adjustments have been checked and adjusted if necessary. Verify that diagnostic trouble codes have been resolved.Observe engine performance during the road test. A poorly tuned engine will not allow accurate analysis of transmission operation. Operate the transmission in all gear ranges. Check for shift variations and engine flare, which indicates slippage. Note if shifts are harsh, spongy, delayed, early, or if part throttle downshifts are sensitive. Slippage indicated by engine flare, usually means clutch , band or overrunning clutch problems. If the condition is advanced, an overhaul will be necessary to restore normal operation. A slipping clutch or band can often be determined by comparing which internal units are applied in the various gear ranges.… Read More
Filed Under (Other Manuals) by Doe Namblas on 02-04-2014
Download 1999-2000 Cadillac Escalade (Old Style) 2002-2004 Cadillac Escalade, Escalade EXT 2003-2004 Cadillac Escalade ESV 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 Chevrolet Silverado 2500 Series Crew Cab, Short Box (New Style) 1996-1999 GMC 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 GMC 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 GMC Sierra Extended Cab Short Box (New Style) 1999-2004 GMC Sierra 1500 Series Regular Cab (New Style) 2000-2004 GMC 1500 Series Yukon, Yukon XL 2001-2004 GMC Sierra 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) 2003-2005 HUMMER H2 with Four Wheel Drive (4WD) or All Wheel Drive (AWD) and One-Piece Propeller Shaft ONLY.… Read More
Filed Under (Pontiac) by Doe Namblas on 31-12-2013
Download 2001 Pontiac Grand Prix V6-3.8L VIN K. Shifter A/T: Service and Repair Shift Control Replacement Removal Procedure 1. Remove the horseshoe clip (1) from front of shift control knob, and remove knob. 2. Remove the Console Trim Plate. 3. Remove the console wiring harness. 4. Remove the console shift control wiring harness. 5. Remove the automatic transaxle range selector cable. 6. Remove the park/lock cable. 7. Remove the console shift control nuts. 8. Remove the console shift control. Installation Procedure 1. Install the console shift control. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the console shift control nuts. ^Tighten the console shift control nuts to 24 Nm (18 ft. lbs.) . 3. install the park/lock cable. 4. Install the automatic transaxle range selector cable. 5. Install the console shift control wiring harness. 6. Install the console wiring harness. 7. Install the Console Trim Plate. 8. Adjust the transaxle range selector cable.… Read More
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 23-12-2013
Download Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Supercede: This bulletin is being revised to update parts information. Please discard Corporate Bulletin Number 06-07-30-023B (Section 07 – Transmission/Transaxle) . Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561.… Read More
Download 2006 Dodge Truck RAM 2500 Truck 2WD L6-5.9L DSL Turbo VIN C Vehicle Level Heating and Air Conditioning Compressor HVAC Compressor Clutch Service and Repair Service and Repair. DENSO A/C COMPRESSOR REMOVAL NOTE: * The compressor clutch assembly can be serviced with the refrigerant system fully-charged. * Typical A/C compressor shown in illustrations. 1. Disconnect and isolate the negative battery cable. 2. Remove the accessory drive belt. 3. Disconnect the engine wire harness from the compressor clutch field coil connector (1) located on the top of the A/C compressor (5). 4. Remove the bolts that secure the A/C compressor to the engine and support the A/C compressor. 5. Carefully remove the compressor clutch field coil connector and wire lead from the connector bracket (2). 6. Remove the compressor shaft bolt (3). A band-type oil filter wrench or a strap wrench may be used to hold the clutch plate (4) from rotating during bolt removal.… Read More
Filed Under (Ford) by Doe Namblas on 02-04-2014
Download FORD: 1999 EXPLORER, RANGER MERCURY: 1999 MOUNTAINEER 6. Inspect the fluid pan for major contamination. ISSUE Slipping transmission shifts and/or delayed or no •If contamination is minimal, clean the main transmission engagements may occur on some control, but do not replace. vehicles. The Electronic Pressure Control (EPC) •If major contamination is present, perform solenoid may cause stress on the attaching bracket. normal transmission overhaul as required, This stress causes the bracket to break and the including main control replacement. Pay EPC solenoid to back out of its bore causing line particular attention to the condition of the pressure to drop too low or fluctuate, allowing friction plates. Repair as required. friction clutches to slip. 7. After repairs are completed, verify concern has ACTION been fixed. Diagnose and inspect for damaged EPC attachment PART NUMBER PART NAME bracket, and replace the bracket and EPC solenoid with new bracket and revised EPC solenoid.… Read More
Download 2001 Dodge Dakota 2001 ACCESSORIES & EQUIPMENT’ ‘Body Control Modules – Dakota & Durango. CENTRAL TIMER MODULE Central Timer Module (CTM) communicates with other modules over Programmable Communication Interface (PCI) bus network. PCI bus is a single wire multiplexed network capable of supporting binary encoded messages shared between multiple modules. Modules are wired in parallel. Messages are addressed to only be recognized by the module(s) in which the message was intended. This reduces the complexity of vehicle wiring and size of wiring harness. CTM fault messages are accessed through 16-pin Data Link Connector (DLC) using Chrysler’s Diagnostic Readout Box (DRBIII(R)) scan tool, or generic scan tool. CTM controls and supports the following features (if equipped). z Battery Saver Functions For Interior & Exterior Lighting z Cargo Lighting z Central Locking & Vehicle Theft Alarm (VTSS) z Chime Warning z Courtesy & Dome Lighting z Dome Lighting Defeat z Door Ajar Switch Status z Door Lock Inhibit z Driver Door Unlock z Enhanced Accident Response z Fog Lights z Headlights & Headlight Time Delay z Intermittent & Speed Sensitive Intermittent Wiper Controls z Optical Horn z Parking Lights z Power Door Locks & Remote Keyless Entry (RKE) z Remote Radio z Rolling (Automatic) Door Locks.… Read More
Filed Under (Chrysler) by Doe Namblas on 10-12-2013
Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More
Filed Under (Dodge) by Doe Namblas on 02-01-2014
Download 2001 Dodge Truck Grand Caravan FWD V6-3.8L VIN L FRONT DISC BRAKE SHOES (DISC/DISC BRAKES) REMOVAL 1. Raise the vehicle. 2. Remove both front wheel and tire assemblies. 3. Begin on one side of the vehicle. 4. Remove the anti-rattle clip from the outboard side of the caliper and adapter. 5. Remove the two caliper guide pin bolts. 6. Remove caliper from caliper adapter and brake rotor. CAUTION: Supporting weight of caliper by the flexible brake fluid hose can damage the hose. 7. Using wire or cord, hang the caliper from the front strut assembly. Support the caliper firmly to prevent weight of caliper from being supported by the brake fluid hose. 8. Remove the outboard brake shoe from the caliper adapter. 9. Pull the inboard brake shoe away from the caliper piston until the retaining clip on shoe is free from the cavity in the caliper piston. 10. Repeat the above procedure on other side of the vehicle.… Read More