2001 Dodge Dakota CENTRAL TIMER MODULE

Download 2001 Dodge Dakota 2001 ACCESSORIES & EQUIPMENT’ ‘Body Control Modules – Dakota & Durango. CENTRAL TIMER MODULE Central Timer Module (CTM) communicates with other modules over Programmable Communication Interface (PCI) bus network. PCI bus is a single wire multiplexed network capable of supporting binary encoded messages shared between multiple modules. Modules are wired in parallel. Messages are addressed to only be recognized by the module(s) in which the message was intended. This reduces the complexity of vehicle wiring and size of wiring harness. CTM fault messages are accessed through 16-pin Data Link Connector (DLC) using Chrysler’s Diagnostic Readout Box (DRBIII(R)) scan tool, or generic scan tool. CTM controls and supports the following features (if equipped). z Battery Saver Functions For Interior & Exterior Lighting z Cargo Lighting z Central Locking & Vehicle Theft Alarm (VTSS) z Chime Warning z Courtesy & Dome Lighting z Dome Lighting Defeat z Door Ajar Switch Status z Door Lock Inhibit z Driver Door Unlock z Enhanced Accident Response z Fog Lights z Headlights & Headlight Time Delay z Intermittent & Speed Sensitive Intermittent Wiper Controls z Optical Horn z Parking Lights z Power Door Locks & Remote Keyless Entry (RKE) z Remote Radio z Rolling (Automatic) Door Locks.… Read More

2001 Dodge Truck Grand Caravan FRONT DISC BRAKE SHOES

Download 2001 Dodge Truck Grand Caravan FWD V6-3.8L VIN L FRONT DISC BRAKE SHOES (DISC/DISC BRAKES) REMOVAL 1. Raise the vehicle. 2. Remove both front wheel and tire assemblies. 3. Begin on one side of the vehicle. 4. Remove the anti-rattle clip from the outboard side of the caliper and adapter. 5. Remove the two caliper guide pin bolts. 6. Remove caliper from caliper adapter and brake rotor. CAUTION: Supporting weight of caliper by the flexible brake fluid hose can damage the hose. 7. Using wire or cord, hang the caliper from the front strut assembly. Support the caliper firmly to prevent weight of caliper from being supported by the brake fluid hose. 8. Remove the outboard brake shoe from the caliper adapter. 9. Pull the inboard brake shoe away from the caliper piston until the retaining clip on shoe is free from the cavity in the caliper piston. 10. Repeat the above procedure on other side of the vehicle.… Read More

2005 Dodge Truck Dakota TRANSMISSION SOLENOID/TRS

Download The transmission solenoid/TRS assembly is internal to the transmission and mounted on the valve body assembly. The assembly consists of six solenoids that control hydraulic pressure to the six friction elements (transmission clutches), and the torque converter clutch. The pressure control solenoid is located on the side of the solenoid/TRS assembly. The solenoid/TRS assembly also contains five pressure switches that feed information to the TCM. OPERATION SOLENOIDS Solenoids are used to control the L/R, 2C, 4C, OD, and UD friction elements. The reverse clutch is controlled by line pressure and the position of the manual valve in the valve body. All the solenoids are contained within the Solenoid and Pressure Switch Assembly. The solenoid and pressure switch assembly contains one additional solenoid, Multi-Select (MS), which serves primarily to provide 2nd and 3rd gear limp-in operation. The solenoids receive electrical power from the Transmission Control Relay through a single wire. The TCM energizes or operates the solenoids individually by grounding the return wire of the solenoid as necessary.… Read More

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall

Download Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine. Condition General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine. Some of these vehicles have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. Correction Dealers are to replace the crankshaft position sensor. Vehicles Involved Involved are certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine and built within these VIN breakpoints: Subject: 06083 — Crankshaft Position Sensor Engine Stall Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine Year Division Model From Through 2001 Chevrolet Silverado iE100004 1E200999 1F100006 1F116767 1M100002 1M103668 1Z100010 1Z100042 2001 Chevrolet Suburban 1G100001 1G174359 1J100010 1J100058 2001 GMC Sierra 1E100003 1E2012022 1F100004 1F113912 1M100023 1M103669 1Z100013 1Z100026.… Read More

2001 Mercedes-Benz SLK320 Engine light is on with no acceleration

Download Vehicle Application: 2000 Mercedes-Benz ML320 3.2L 2001 Mercedes-Benz E320 3.2L 2001 Mercedes-Benz C240 2.6L 2001 Mercedes-Benz E320 4Matic 3.2L 2001 Mercedes-Benz C320 3.2L 2002 Mercedes-Benz ML320 3.2L Customer Concern: Engine light is on with no acceleration. Fault code is P0120. Tests/Procedures: 1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 2. If voltages are out of specification verify correct reference voltage to sensor by measuring between pins 6 (Black/White wire) and pin 1 (Blue/Grey wire) on pedal sensor connector. Voltage needs to be between 4.75 and 5.25 volts. 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value.… Read More

2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More

2007 Chevrolet Impala Transmission 1-2 Shift Shudder at Light to Moderate Acceleration

Download Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Supercede: This bulletin is being revised to update parts information. Please discard Corporate Bulletin Number 06-07-30-023B (Section 07 – Transmission/Transaxle) . Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561.… Read More

1997 – 2001 Infiniti Q45 ENGINE WILL NOT START

Download 2000 – 2001 I30 (CA33) 1999 I30 (CA32) 1999.5 – 2001 QX4 (JR50) 1997 – 2001 Q45 (FY33) 2000 – 2001 G20 (P11) APPLIED VINS: All APPLIED DATES: Start of production SERVICE INFORMATION This bulletin describes and introduces new features of the Infiniti Vehicle Immobilizer System/Nissan Anti-Theft System (IVIS/NATS). The system is standard equipment on each of the applied vehicles listed above. The IVIS/NATS will not allow the engine to start without the use of a registered ignition key. If a vehicle will not start and the Security lamp is on solid, it may be because the ignition keys were not properly registered into the vehicle’s NATS IMMU (Immobilizer control unit). In this case, there will be a “DIFFERENCE OF KEY” code stored in the NATS IMMU. When the NATS ignition key, IMMU, or ECM (ECCS control unit) are replaced, C/U initialization is necessary. It is also necessary when registering keys and as part of many NATS Service Manual diagnostic procedures.… Read More

1999-2001 Infiniti Q45 (FY33) MIL “ON” REAR O2 SENSOR DTC

Download 1999-2001 Q45 (FY33) SERVICE INFORMATION If a 1999, 2000, or 2001 Q45 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) • P0158 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Max. Voltage Monitoring) • P0159 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Response Monitoring) • P0160 Heated Oxygen Sensor 2 (Rear) (Bank 2) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies.… Read More