2001 chevy malibu coolant sensor diagram

You search Auto repair manual PDF about 2001 chevy malibu coolant sensor diagram, search results will appear below. If search results do not exist, please search by others keyword.

1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

Filed Under (Saturn) by admin on 24-02-2014

Download 1999 Saturn SL1 L4-1.9L SOHC VIN 8 Vehicle Level Powertrain Management Computers and Control Systems Coolant Temperature Sensor/Switch (For Computer) Technical Service Bulletins All Technical Service Bulletins Engine – Driveability Concerns/Cooling System DTC’s Set. SUBJECT: Engine Coolant Temperature Sensor Related Diagnostic Trouble Code(s) and/or the Following Conditions: Hard Start, Erratic Idle, Rough Running. Engine Overheating, Low and/or Leaking Coolant, and/or Service Engine Soon Lamp Illuminated. (Replace Engine Coolant Temperature Sensor with New Design Sensor- P/N 21025106) MODELS AFFECTED: 1991-2001 Saturn S-Series vehicles CONDITION: Customers may comment about various driveability and/or engine operating concerns including: hard start, erratic idle, rough running, engine overheating, low and/or leaking coolant, and/or Service Engine Soon lamp illuminated. CAUSE: This condition may be caused by a cracked engine coolant temperature sensor. CORRECTION: Replace engine coolant temperature sensor, inspect and if necessary replace sensor harness connector. Refer to procedure in this bulletin to replace engine coolant temperature sensor and Parts Requirements for specific parts information.… Read More

2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Filed Under (Infiniti) by admin on 16-12-2013

Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine. Condition General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine. Some of these vehicles have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. Correction Dealers are to replace the crankshaft position sensor. Vehicles Involved Involved are certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine and built within these VIN breakpoints: Subject: 06083 — Crankshaft Position Sensor Engine Stall Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine Year Division Model From Through 2001 Chevrolet Silverado iE100004 1E200999 1F100006 1F116767 1M100002 1M103668 1Z100010 1Z100042 2001 Chevrolet Suburban 1G100001 1G174359 1J100010 1J100058 2001 GMC Sierra 1E100003 1E2012022 1F100004 1F113912 1M100023 1M103669 1Z100013 1Z100026.… Read More

2004 Chevrolet Chevy Suburban Gradual Coolant Loss Over Time with No Evidence of Leak Found

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download 2004 Chevrolet Chevy Suburban – 4WD | Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) Service Manual. Information on Gradual Coolant Loss Over Time with No Evidence of Leak Found. Models: 2004-2006 Buick Rainier 2001-2006 Cadillac Escalade Models 2001-2006 Chevrolet Avalanche, Blazer, Silverado, Suburban, Tahoe, TrailBlazer Models 2001-2006 GMC Envoy, Jimmy, Sierra, Yukon Models 2001-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.8L or 5.3L VORTEC® GEN III, GEN IV V8 Engine (VINs V, T, M, B, Z – – RPOs LR4, LM7, LH6, L33, L59) Some vehicles may experience a gradual coolant loss over time. A very low percentage of cylinder head(s) manufactured with an embossed Castech logo may develop a porosity crack in a very specific area. Inspect the cylinder head assembly to determine if the casting was manufactured by Castech. This can be accomplished by inspecting for their casting logo located on top of the intake port, under the rocker arm support rail and in the spring deck cavity portion of the cylinder head.… Read More

2001 Mercedes-Benz SLK320 Engine light is on with no acceleration

Filed Under (Mercedes-Benz) by admin on 26-11-2013

Download Vehicle Application: 2000 Mercedes-Benz ML320 3.2L 2001 Mercedes-Benz E320 3.2L 2001 Mercedes-Benz C240 2.6L 2001 Mercedes-Benz E320 4Matic 3.2L 2001 Mercedes-Benz C320 3.2L 2002 Mercedes-Benz ML320 3.2L Customer Concern: Engine light is on with no acceleration. Fault code is P0120. Tests/Procedures: 1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 2. If voltages are out of specification verify correct reference voltage to sensor by measuring between pins 6 (Black/White wire) and pin 1 (Blue/Grey wire) on pedal sensor connector. Voltage needs to be between 4.75 and 5.25 volts. 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value.… Read More

1999 Pontiac Grand Am SE RIGHT FRONT WHEEL SPEED SENSOR CIRCUIT OPEN OR SHORTED

Filed Under (Pontiac) by admin on 27-01-2014

Download 1999 Pontiac Grand Am SE 1998-99 BRAKES Anti-Lock/TCS – ABS-VI – Cars. DTC C1233: RIGHT FRONT WHEEL SPEED SENSOR CIRCUIT OPEN OR SHORTED 1. Perform diagnostic system check. See DIAGNOSTIC SYSTEM CHECK. After performing diagnostic system check, go to next step. 2. Turn ignition off. Spray right front wheel speed sensor jumper harness thoroughly with a 5 percent saltwater solution (2 teaspoons of salt to 12 ounces of water). Disconnect EBCM/EBTCM connector C1 (“W” body), connector C2 (“J” body, Cutlass and Malibu) or 32-pin connector (Achieva, Alero, Grand Am and Skylark). See EBCM/EBTCM LOCATION under REMOVAL & INSTALLATION. Using DVOM, measure resistance between speed sensor signal high circuit and speed sensor signal low circuit of EBCM/EBTCM connector. On “W” body, resistance should be 1020-1137 ohms at 68°F (20°C). On “J” body, Achieva, 1998 Grand Am and Skylark, resistance should be 1530-1870 ohms at 68°F (20°C). On Alero, Cutlass, 1999 Grand Am and Malibu, resistance should be 950-1250 ohms at 68°F (20°C).… Read More

1999-2001 Infiniti Q45 (FY33) MIL “ON” REAR O2 SENSOR DTC

Filed Under (Infiniti) by admin on 10-01-2014

Download 1999-2001 Q45 (FY33) SERVICE INFORMATION If a 1999, 2000, or 2001 Q45 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) • P0158 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Max. Voltage Monitoring) • P0159 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Response Monitoring) • P0160 Heated Oxygen Sensor 2 (Rear) (Bank 2) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies.… Read More

2002 Ford Escort Cooling System Draining, Filling and Bleeding Workshop Manual

Filed Under (Ford) by admin on 25-01-2014

Download Draining 1. Bring the engine to normal operating temperature and turn the engine off. With the cooling system under pressure, inspect cooling system hoses and clamped hose connections for leaks, excessive deterioration or contact wear. Inspect radiator installation retention. Note any discrepancies and proceed. 2. WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap.… Read More

2001 Lincoln LS Workshop Manual

Filed Under (Lincoln) by admin on 01-01-2014

Download Cooling System Draining, Filling and Bleeding. Draining WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap. CAUTION: The coolant must be recovered in a suitable, clean container for reuse. If the coolant is contaminated it must be recycled or disposed of correctly. CAUTION: Care must be taken to ensure the accessory drive belt does not become contaminated with engine coolant.… Read More

Rapid Flow Induction Installation Instructions

Filed Under (Ford) by admin on 25-12-2013

Download 1. Disconnect the coolant overfill hose, this will make the removal of the stock intake easier. 2. Disconnect the Mass Air Flow sensor: • (’03, ’04, ’06, ’07) Using a bit driver and the torques bit included unscrew the torques screws that hold the mass air flow sensor onto the air intake exit tube. Once the screws are out pull the mass air flow sensor out of the tube, disconnect it from the harness holder and move it aside while completing the installation. • 2005 The mass air flow sensor sits in a grommet that holds it in place on the intake exit tube. Remove the MAF sensor by simply pulling up on the sensor, then disconnect it from the harness holder and move it aside while completing the installation. Also remove the grommet that holds the MAF sensor in place from the stock intake, that grommet will need to be installed on the RFI along with the MAF sensor.… Read More

You might also likeclose