2000 s10 shift lever

You search Auto repair manual PDF about 2000 s10 shift lever, search results will appear below. If search results do not exist, please search by others keyword.

Ford C-4 Bracket and Lever Installation Instructions

Filed Under (Ford) by admin on 01-09-2012

Download STEP 1. Raise and safely support the vehicle at least 1-2 feet off the ground. Remove the nut and lock- washer holding the downshift linkage onto the downshift lever shaft. The downshift lever is the outer lever on C-4 transmissions. Pull the lever off the shaft and allow the linkage to hang free. Remove and discard stock shift linkage rods. Late C-4 transmissions have a Neutral safety/Backup light switch on the transmission shift lever. If your transmission is so equipped, remove the two bolts holding the switch in place and slide it off the shift shaft. Disconnect the switch at the factory plug and discard it. STEP 2. Install the B&M selector lever, See figure 1 . Note: The B&M lever must point downward for proper operation. If the stock shift lever on your transmission points down, you will have to remove the lower part of the stock arm by cutting it off to clear the B&M lever, (See figure 1 ) .… Read More

1996-1999 Audi A4/1998 VW Passat Short Shifter Installation Instructions

Filed Under (Audi) by admin on 18-02-2014

Download The following parts are included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: – 13mm socket and ratchet – 10mm socket and ratchet – socket wobble (universal joint) attachment – socket extension – snap ring / circlip pliers – 6mm allen socket head bit – flexible plunger-type four-claw retriever – torx T-25 driver (only for 2000 A4, S4 and A6 Biturbo) Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console. Step 3 – Remove black plastic collar Step 4 – Remove circlip Use circlip pliers to remove circlip from shift lever.… Read More

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Filed Under (Chrysler) by admin on 10-12-2013

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

Audi A4 B6/8E 5 Speed Short Shifter Installation Manual

Filed Under (Audi) by admin on 21-12-2013

Download A. Required Tools Safety Glasses (! See Warnings!) Circlip Pliers Hose Clamp Cutter Razor Blade Ratchet 3/8 or 1/4 Inch Drive Sockets Metric 3/8 or 1/4 Drive (7mm & 10mm) Extension Medium Length 3/8 or 1/4 Inch Drive 6mm Allen Key 6mm Allen Socket 2.5mm Allen key (Included in kit) T-25 Torx Driver 10mm Wrench 24mm or Adjustable Wrench. Step 1: Removal of console cover plate and shift knob. To remove the cover plate, open the ashtray and pull up on the front of the cover. Do the same for the rear of the cover by lifting from within the shift boot at the rear side. To remove the shift knob you must cut the clamp holding the shift knob we have included a new one in the kit. (! Safety glasses are required while cutting the hose clamp!) Once you have removed the clamp, pull up on the shift knob to remove it.… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Filed Under (Chevrolet (Chevy)) by admin on 28-11-2013

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

Audi S4/A6 Biturbo Short Shifter Installation Instructions

Filed Under (Audi) by admin on 26-03-2014

Download included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: • ¼” ratchet • 10mm open end/box end wrench • 10mm socket • 3/8″ open end/box end wrench • 3/8″ socket or a 2nd 3/8″ box end wrench • flexible plunger-type four-claw retriever • socket wobble (universal joint) attachment • 1/8″ allen hex key wrench • socket extension • 6mm allen socket head bit • snap ring / circlip pliers Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Unscrew the shift knob from the original lever. Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Filed Under (Jeep) by admin on 02-01-2014

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More

1988-2007 Honda Shadow VT600 Zombie Levers Installation Manual

Filed Under (Honda) by admin on 31-12-2013

Download
PROCEDURE: CLUTCH LEVER STEP 1 Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn off the ignition. STEP 2 Tighten the cable adjustment screw on the clutch perch in toward the lever to gain adequate slack for removing the clutch cable. STEP 3 When you have enough slack in the cable, you can remove the cable from the lever by lining up the slot on the adjustment screw and removing the cable from the lever. STEP 4 Remove the hardware that secures the lever to the perch. INSTALLATION STEP 5 With the old lever removed, you can install the new Zombie lever and secure it with the stock hardware removed in step 4. STEP 6 You can re-secure the clutch cable and tighten up the slack by turning the cable adjuster. You will want about a 1/8″ of play in the clutch lever after installation of the new Zombie lever.… Read More

2007 Honda CB600 HORNET ASV C/5 Part# CRC510

Filed Under (Honda) by admin on 24-11-2013

Congratulations on your purchase of an ASV C/5 Sport Streetbike lever. The correct installation of control levers on a sport/street motorcycle is critical. Incorrect installation or the installation of an incorrect part can result in a malfunction of your clutch and / or front brake system. This lever should be installed by a certified mechanic; preferably at your local motorcycle dealer service dept. ASV Inventions, Inc. accepts no liability for malfunctions as a result of incorrect installation or the installation of a part that was not designed specifically for your motorcycle. Please check the list below to confirm that the correct year, make and model of your motorcycle is listed. If the correct year, make and model of your motorcycle is not listed below, then this part is notthe correct part for your motorcycle and must not be installed onto your motorcycle. Tools and supplies needed: 1) 10mm wrench or socket, 1) Flat blade screwdriver.… Read More

You might also likeclose