, search results will appear below. If search results do not exist, please search by others keyword.
Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More
Download 2000 Chevy Truck S10/T10 Transfer Case Replacement
Download Models: 2004-2007 Buick Rainier 2003-2006 Chevrolet Avalanche, Suburban, Tahoe 2003-2007 Chevrolet Silverado Classic, TrailBlazer, TrailBlazer EXT 2003-2006 GMC Yukon, Yukon XL 2003-2007 GMC Envoy, Envoy XL, Sierra Classic 2003-2004 Oldsmobile Bravada 2005-2007 Saab 9-7X with Four Wheel Drive or All-Wheel Drive and Active All-Wheel Drive (RPO NP4) or Active Two-Speed (RPO NP8) Transfer Case. Condition Some customers may comment on intermittent illumination of the Service 4WD light. Upon investigation, the technician may find DTC C0374 set. The customer may also comment on intermittent erratic operation of the 4WD or AWD system after driving through rain/snow or simply going through a car wash. Cause The speed sensor signal may have become corrupted. Possible openings in the speed sensor wire insulation (twisted pairs) can allow water intrusion. Also, wire connections contaminated by water may result in short circuits and erroneous speed sensor readings. This most often occurs on the rear speed sensor circuit.… Read More
Download Service 4WD Light Illuminated, DTC C0374 Set (Inspect Wiring Harness to Transfer Case Speed Sensors, Replace Wiring Harness)
Download Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada.… Read More
Download Vehicles Equipped with a Webasto Sunroof System
Download FORD: 1995-1997 EXPLORER 2. Connect the New Generation Star (NGS) Tester ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL.… Read More
Download 1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Download 1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions
Download EMS P/N 30-6051 (4 cylinder Acura/Honda vehicle with 6 cylinder engine and harness swap) Vehicle: 2000-2001 Acura Integra 1998-1999 Acura 2.3CL 1996-2000 Honda Civic Engine wiring harness: 1999-2002 Honda Accord V6 J30A1 1999 Acura CL 3.0L J30A 2001-2003 Acura CL 3.2L J32A1 (auto harness only) 1999-2003 Acura TL 3.2L J32A1 2002-2003 Acura CL/TL 3.2L Type S J32A2 (auto harness only) 2002-2004 Honda Odyssey 3.5L J35A4. Wiring accessories to the EMS: Please follow this suggested wiring diagram when adding/retaining original accessories such as the speedometer, reverse lockout, UEGO gauges, MAP sensors, IAT sensors, or switches for use with the EMS. Note that wire polarity is not important for the Air Temperature sensor. 1) Install AEMTuner software onto your PC The latest version of the AEMTuner software can be downloaded from the AEMTuner section of the AEM Performance Electronics forums. Series 2 units are not supported by the older AEMPro tuning software.… Read More
Download 2000-2001 Acura Integra AEM EMS System Installation Instructions
Download odels: 1995-1996 Buick Roadmaster 1995-1999 Buick LeSabre 1995-2004 Buick Century, Regal 1995-2005 Buick Park Avenue 1996-1999 Buick Riviera, Skylark 2004-2005 Buick Rainier 1995-1999 Chevrolet Lumina, Monte Carlo, Fullsize Pickup Models (Old Style) 1995-2005 Chevrolet Blazer 1996 Chevrolet Lumina APV 1996-1999 Chevrolet Cavalier 1996-2000 Chevrolet Express Van 1996-2002 Chevrolet Astro Van 1997-2002 Chevrolet Camaro 1997-2003 Chevrolet Malibu 1997-2005 Chevrolet Corvette, Venture 2000-2005 Chevrolet Silverado 2002-2005 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2005 Chevrolet SSR 2004-2005 Chevrolet Classic, Colorado 1995-1999 GMC Fullsize Pickup Models (Old Style) 1995-2002 GMC Jimmy 1996-2000 GMC Savana Van 1996-2002 GMC Safari Van 2000-2005 GMC Sierra 2002-2005 GMC Envoy, Envoy XL 2004-2005 GMC Canyon, Envoy XUV 1995-1999 Oldsmobile Aurora, Eighty Eight 1995-1997 Oldsmobile Cutlass Supreme 1999-2004 Oldsmobile Alero 1998-2002 Oldsmobile Intrigue 1995-1996 Oldsmobile Ninety Eight 1996-1999 Oldsmobile Achieva 1996-2004 Oldsmobile Bravada, Silhouette 1995-1999 Pontiac Bonneville, Sunfire 1995-2002 Pontiac Firebird 1995-2005 Pontiac Grand Prix 1996-1997 Pontiac Trans Sport 1996-2000 Pontiac Grand Am 1997-2005 Pontiac Montana 2003-2005 HUMMER H2.… Read More
Download Information on Error Codes on Radio Display – Their Cause and Corrective Action
Download 1. SAFETY REQUIREMENTS STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation. 1. Always wear safety glasses for eye protection. 2. Place ignition switch in the OFF position. 3. Always apply the parking brake when working on a vehicle. 4. Block the front and rear tire surface to prevent unexpected vehicle movement. 5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. 6. Do not smoke or use flammable items near or around the fuel system. 7. Use chemicals and cleaners in well-ventilated areas. 8. Batteries produce explosive gases, which can cause personal injury.… Read More
Download 2005 Ford Mustang GT Roush Fog Lamp Wiring Harness Installation Instructions
Vehicle: 2000-2001 Acura Integra, 1998-1999 Acura 2.3CL, 1996-2000 Honda Civic.
Engine wiring harness: 1999-2002 Honda Accord V6 J30A1, 1999 Acura CL 3.0L J30A, 2001-2003 Acura CL 3.2L J32A1 (auto harness only), 1999-2003 Acura TL 3.2L J32A1, 2002-2003 Acura CL/TL 3.2L Type S J32A2 (auto harness only), 2002-2004 Honda Odyssey 3.5L J35A4.
The AEM Engine Management System (EMS) is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM EMS differs from all others in several ways. The EMS is a stand alone system, which completely replaces the factory ECU and features unique Plug and Play Technology, which means that each system is configured especially for your make and model of car without any jumper harnesses. There is no need to modify your factory wiring harness and in most cases your car may be returned to stock in a matter of minutes.… Read More
Download Honda/Acura Engine Management System (EMS) Manual Installation Instructions
These 5 adjustments are not active when a ME-RC Remote Control with revision 1.5 or higher is used. They are set using displays under the AGS button on the remote control. Gen Run Signal (input to pin 2 must be 10 to 40 DC volts only while generator is running); this can be the generator hour-meter or a 12vdc pilot/run light
ME-AGS relay timing for 3-Wire Mode. Magnum Energy, Inc. provides this diagram to assist in the installation of the Auto-Generator Start controller. Since the use of this diagram and the conditions or methods of installation, operation and use are beyond the control of Magnum Energy, Inc., we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of the installation, operation and use of this unit.… Read More
Download Honda Generator EM3800SX EM5000SX ME-AGS Wiring Diagram