2000 jetta auto trans to manual swap need wiring diagram switch

You search Auto repair manual PDF about 2000 jetta auto trans to manual swap need wiring diagram switch, search results will appear below. If search results do not exist, please search by others keyword.

2000 Volkswagen Cabrio Ignition Switch: Service and Repair

Filed Under (Volkswagen (VW)) by admin on 02-01-2014

Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More

1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions

Filed Under (Honda) by admin on 27-02-2014

Download
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More

2000 Cadillac DeVille Brake Switch Circuit Low Input

Filed Under (Cadillac) by admin on 06-04-2014

Download . Circuit Description The torque converter clutch (TCC) brake switch is used to indicate the status of the brake pedal (applied or released). If the PCM detects an open TCC brake switch (stuck ON) during accelerations, then DTC P0719 sets. DTC P0719 is a type C DTC. Conditions for Running the DTC * No VSS DTCs P0502 or P0503. * DTC P0719 has not passed this ignition cycle. Conditions for Setting the DTC The TCC brake switch input is at 0 volts for 15 minutes and the following conditions occur 8 times without a status change on the TCC brake input: * The vehicle speed is less than 8 km/h (5 mph). * The vehicle accelerates to 32 km/h (20 mph) within 2-6 seconds. * Then the vehicle speed remains above 32 km/h (20 mph) for 6 seconds. Action Taken When the DTC Sets * The PCM does not illuminate the malfunction indicator lamp (MIL).… Read More

2005 Ford Mustang GT Roush Fog Lamp Wiring Harness Installation Instructions

Filed Under (Ford) by admin on 01-01-2014

Download 1. SAFETY REQUIREMENTS STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation. 1. Always wear safety glasses for eye protection. 2. Place ignition switch in the OFF position. 3. Always apply the parking brake when working on a vehicle. 4. Block the front and rear tire surface to prevent unexpected vehicle movement. 5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. 6. Do not smoke or use flammable items near or around the fuel system. 7. Use chemicals and cleaners in well-ventilated areas. 8. Batteries produce explosive gases, which can cause personal injury.… Read More

Honda/Acura Engine Management System (EMS) Manual Installation Instructions

Filed Under (Acura) by admin on 03-04-2014

Download
Vehicle: 2000-2001 Acura Integra, 1998-1999 Acura 2.3CL, 1996-2000 Honda Civic.
Engine wiring harness: 1999-2002 Honda Accord V6 J30A1, 1999 Acura CL 3.0L J30A, 2001-2003 Acura CL 3.2L J32A1 (auto harness only), 1999-2003 Acura TL 3.2L J32A1, 2002-2003 Acura CL/TL 3.2L Type S J32A2 (auto harness only), 2002-2004 Honda Odyssey 3.5L J35A4.
The AEM Engine Management System (EMS) is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM EMS differs from all others in several ways. The EMS is a stand alone system, which completely replaces the factory ECU and features unique Plug and Play Technology, which means that each system is configured especially for your make and model of car without any jumper harnesses. There is no need to modify your factory wiring harness and in most cases your car may be returned to stock in a matter of minutes.… Read More

2000-2004 Audi TT Coupe Brake System

Filed Under (Audi) by admin on 31-12-2013

Download Audi TT Coupe 2000-2004, Audi TT Roadster 2001-2004 – Brake System. ABS/ESP ITT Mark 20 system components, removing and installing Brake light switch (square housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once. Removing – Remove storage compartment on driver’s side. Repair Manual, Body Interior, Repair Group 68; Storage compartments, covers – Unplug electrical connector. – Remove brake light switch -1- by turning counter-clockwise through 90. Installing Install in reverse sequence; note the following points: – Pull brake light switch plunger fully out. – Press brake pedal down as far as possible by hand. – Guide switch through installation hole and secure by turning 90 clockwise -arrows-. – Release brake pedal. – Make sure proper function of brake lights when brake pedal is pressed and released. Brake light switch (round housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once.… Read More

2000-2001 Acura Integra AEM EMS System Installation Instructions

Filed Under (Acura) by admin on 02-01-2014

Download EMS P/N 30-6051 (4 cylinder Acura/Honda vehicle with 6 cylinder engine and harness swap) Vehicle: 2000-2001 Acura Integra 1998-1999 Acura 2.3CL 1996-2000 Honda Civic Engine wiring harness: 1999-2002 Honda Accord V6 J30A1 1999 Acura CL 3.0L J30A 2001-2003 Acura CL 3.2L J32A1 (auto harness only) 1999-2003 Acura TL 3.2L J32A1 2002-2003 Acura CL/TL 3.2L Type S J32A2 (auto harness only) 2002-2004 Honda Odyssey 3.5L J35A4. Wiring accessories to the EMS: Please follow this suggested wiring diagram when adding/retaining original accessories such as the speedometer, reverse lockout, UEGO gauges, MAP sensors, IAT sensors, or switches for use with the EMS. Note that wire polarity is not important for the Air Temperature sensor. 1) Install AEMTuner software onto your PC The latest version of the AEMTuner software can be downloaded from the AEMTuner section of the AEM Performance Electronics forums. Series 2 units are not supported by the older AEMPro tuning software.… Read More

2000 Volkswagen Beetle Vehicle starts and stalls

Filed Under (Volkswagen (VW)) by admin on 01-01-2014

Download Vehicle Application: 2000 Volkswagen Beetle 2.0L, GAS, Eng Des AEG 2002 Volkswagen Beetle 2.0L, GAS, Eng Des AZG 2000 Volkswagen Jetta GL 2.0L 2002 Volkswagen Eurovan 2.8L 2000 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AEG 2002 Volkswagen Jetta GL 2.0L, Eng Des AVH 2000 Volkswagen Jetta GLS 2.8L, Eng Cfg V6, Eng Des AFP 2002 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AVH 2001 Volkswagen Beetle 2.0L, GAS, Eng Des AVH 2002 Volkswagen Jetta GLS Wagon 1.8L 2001 Volkswagen Jetta GL 2.0L, Eng Des AEG 2003 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AVH, USA/Canada 2001 Volkswagen Jetta GLX 2.8L 2007 Volkswagen Passat 3.6 3.6L 2002 Volkswagen Beetle 1.9L, DIESEL, Turbo, Eng Des ALH Customer Concern: Vehicle starts and stalls. Trouble code P1570 (17978). The security light is flashing. Tests/Procedures: 1. As of model year 2000, Volkswagen has changed the immobilizer system and the 7 digit PIN numbers are no longer available to the aftermarket.… Read More

Honda Civic Acura Integra Gauge Bezel Manual Installation Instructions

Filed Under (Honda) by admin on 31-03-2014

Download
NOTE: Gauge bezel can be painted using a plastic safe paint. 1. Remove stock gauge bezel. 2. Acura Integra – Drill 7? 64 ” hole in the plastic cross member. Install aluminum bracket (Fig. 1). Bracket stud should align with hole in lower center of gauge bezel. Honda Civic – Remove bottom center screw from gauge cluster housing. Reinstall screw and supplied aluminum bracket (Fig. 2). 3. Install gauges in new gauge bezel (gauges are press fit). 4. Install new gauge bezel using supplied screws in the top and bottom center of the new bezel to attach the bezel to the aluminum bracket. There are no clips on the new bezel. 5. Run gauge wiring out through the firewall.
SERVICE For service send your product in a well packed shipping carton to the address below. Please include a note explaining what the problem is along with your phone nu m b e r.… Read More

1996-2000 Honda Civic D16Y8 Performer X Turbocharging System Manual Installation Instructions

Filed Under (Honda) by admin on 01-01-2014

Download
Description: The Edelbrock Performer X Turbocharging System is a complete Turbo Kit that gives 1996-2000 Honda Civic SOHC VTEC D16Y8 owners a 60-70 horsepower increase from turbocharging. The Garrett T-28 ball bearing turbo comes pre-assembled as one unit with a Ni-resist cast exhaust manifold and exhaust elbow, and inlet oil and water lines for the simplest possible installation. The system includes a high-performance Performer X intake manifold with four additional injectors and a separate electronic controller to add fuel and retard spark under boosted conditions. The Edelbrock Exhaust manifold and elbow are designed for maximum flow and high velocity for quicker turbo spool-up. We have included an intercooler, blow-off valve, windshield pillar mount boost gauge, o-ring sealed compressor flanges, a turbo oil supply adapter, and pre-assembled Russell oil, water, and fuel lines to make this one of the most complete kits on the market.
INSTALLATION INSTRUCTIONS Initial Parts Removal and Intercooler Installation (See factory service manual for procedures where noted) 1.… Read More

You might also likeclose