2000 ford windstar alternator wire diagram

You search Auto repair manual PDF about 2000 ford windstar alternator wire diagram, search results will appear below. If search results do not exist, please search by others keyword.

1999-2000 Ford Windstar The battery light is on, but the alternator is charging Has a code P1246

Filed Under (Ford) by admin on 18-01-2014

Download Direct-Hit 2000 Ford Windstar 3.8L Test Details Hotline Archive # 124501 Confirmed Fix Vehicle Application: 1999 Ford Windstar 3.8L, Vin 4 2003 Ford Windstar 3.8L 2000 Ford Windstar 3.8L, Vin 4 Customer Concern: The battery light is on, but the alternator is charging. Has a code P1246. Tests/Procedures: 1. Disconnect the alternator and the Powertrain Control Module (PCM). Check the Violet (VT) (GENerator MONitor or GENMON) wire from the alternator to pin 20 of the PCM connector and the Red/Pink (RD/PK) (GENerator COMmand or GENCOM) wire from the alternator to pin 45 of the PCM for high resistance, an open, or a short to ground. Repair the wiring as needed. 2. If the wiring checks OK, reconnect the PCM and alternator. Start the engine and monitor the VT wire for a roughly 0-10v square wave signal. The signal will be around 40-50% normally with no loads on the system and minimal charging system output.… Read More

556H Honda / Acura Immobilizer Bypass Module Installation Instruction

Filed Under (Honda) by admin on 29-01-2014

Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Filed Under (Acura) by admin on 24-11-2013

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Filed Under (Ford) by admin on 24-11-2013

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Filed Under (Ford) by admin on 02-01-2014

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

2000-2007 Ford Taurus ERRATIC FLUID LEVEL READING ON TRANSAXLE DIPSTICK

Filed Under (Ford) by admin on 15-02-2014

Download Ford : 2000-2007 Taurus 2000-2003 Windstar 2004-2007 Freestar MERCURY: 2000-2005 Sable 2004-2007 Monterey. ISSUE: Some 2000-2007 Taurus, 2000-2005 Sable, 2000-2003 Windstar, and 2004-2007 Freestar/Monterey vehicles, equipped with a 4F50N, AX4N, or AX4S transaxle, may exhibit an erratic fluid level reading on the transaxle dipstick and possible leaks around the filler tube and grommet. The condition may be due to a restricted transaxle vent. ACTION: Repair the transaxle vent restriction by replacing the transaxle vent with a 90° vent stem, small hose clamp, two (2) tie raps, and 24″ (61 cm) of 5/16″ (8 mm) vacuum hose. The 5/16″ (8 mm) vacuum hose will be routed from the 90° vent on the transaxle back to the cowl area, next to the brake master cylinder and tie rapped in place with the end of the hose facing down. Refer to the following Service Procedures. SERVICE PROCEDURE 1. Disconnect the mass air flow (MAF) sensor electrical connector.… Read More

Ford-Toyota-Lexus 555F Interface Module Wiring Installation Instructions

Filed Under (Ford) by admin on 13-01-2014

Download The 555F interface module is used when installing remote start products in Ford, Toyota and Lexus vehicles equipped with factory immobilizers. The 555F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. WIRE CONNECTION GUIDE FOR FORDS RED (+)12V: Connect this wire to a fused (+)12V source. BLUE (-) ACTIVATION INPUT: Connect this wire to the (-) through activation output of the remote start system. 555FCAPSULE: The 555F capsule should be placed on the outside of the antenna ring as close to the ribbon cable as possible. LEARNING THE 555F CAPSULE FOR FORDS To program the 555F capsule for a Ford vehicle, use the procedure that corresponds to the appropriate vehicle year. 1996 and 1997 Ford Vehicles: 1. Install the remote start and make the appropriate wire connections on the 555F. 2. Make sure that the 555F capsule can reach the front of the key cylinder where the key is inserted.… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 17-03-2013

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

1997 – 2002 Ford Econoline GRDP6 Guardian or Guardian II Lift Interlocks Installation Instructions

Filed Under (Ford) by admin on 13-12-2013

Download Use the instructions that were included with the original Guardian or Guardian II kit, and make the following modifications: VEHICLE 1 HARNESS – 1997-2002 Econoline with Gas Engine and Transmission Code E or 9 only – This application will not have a Ford OEM Blunt cut wire for “Park”. An auxiliary 4-pin Park Harness (Part # GRDP6) will be needed and the Vehicle 1 Harness will need to be modified. Cut the Orange wire on the Vehicle 1 harness near the connector. Save the grommet, and discard the Orange wire. Locate the Ford gray 4-pin connector located above the transmission bell housing. Separate the connector halves and connect the gray “T” harness connectors from the GRDP6 Harness between them. Drill a 5/8″ hole in the bulkhead flange for the engine cover (see picture). Feed the two green wires through the hole from the engine compartment. Slide the saved grommet onto the harness and secure in the hole.… Read More

Audi A8 D3 Sony HCB-30 Bluetooth Kit Installation Checklist

Filed Under (Audi) by admin on 31-12-2013

Download kit Torx T-35 screwdriver Soldering iron Solder Heat gun or other heat source to heat shrink tubing Drill with 3/8″ bit Small wire cutters Wire strippers that go down to 20 gage wire Electrical Tape Drop or Flash Light Hanger for pulling wire Step Description Completed (check) 1 Place Telematics box in Service Mode. 2 Remove Fuse SB13. 3 Remove driver’s side trim and Telematics box from under carpet. 4 Disconnect wiring from Telematics box. Drill hole for wiring harness. Modify six connections on the 42 pin connector. 5 Install cover on 42 pin connector, plug into Telematics box, install Fuse SB13. Plug all components into HCB- 30 brain box, turn on ignition and test. 6 Mount HCB-30 brain box, run wiring. 7 Replace Telematics box, replace carpet. 8 Mount and route the microphone and wire. 9 Mount and route the touch pad and wire. 10 Take Telematics box out of Service Mode.… Read More

You might also likeclose