FORD PATS (PASSIVE ANTI THEFT SYSTEM) INITIALIZATION WITH THE 2534 GLOBAL PROGRAMMER

Download There are five types of PATS implementations from Ford (A, B, C, D, E). Refer to Table 1 (page 11) to identify what type of PATS your vehicle is equipped with. PATS initialization is generally performed after programming. The A or D version of PATS does not store the key information in the PCM, therefore NO PATS KEY RELEARN IS REQUIRED after programming. The B or C versions of PATS store the key information within the PCM and MUST be transferred to the new PCM, or relearned on the vehicle after the new PCM is installed. The E version of PATS also stores the key information within the PCM, but CANNOT be transferred to the new PCM. This type MUST be relearned on the vehicle after the new PCM is installed. Note: If you are just updating the existing PCM calibration with an update calibration, you must select the MODULE REPROGRAMMING function (not Programmable Module Installation).… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

1999-2000 Ford Windstar The battery light is on, but the alternator is charging Has a code P1246

Download Direct-Hit 2000 Ford Windstar 3.8L Test Details Hotline Archive # 124501 Confirmed Fix Vehicle Application: 1999 Ford Windstar 3.8L, Vin 4 2003 Ford Windstar 3.8L 2000 Ford Windstar 3.8L, Vin 4 Customer Concern: The battery light is on, but the alternator is charging. Has a code P1246. Tests/Procedures: 1. Disconnect the alternator and the Powertrain Control Module (PCM). Check the Violet (VT) (GENerator MONitor or GENMON) wire from the alternator to pin 20 of the PCM connector and the Red/Pink (RD/PK) (GENerator COMmand or GENCOM) wire from the alternator to pin 45 of the PCM for high resistance, an open, or a short to ground. Repair the wiring as needed. 2. If the wiring checks OK, reconnect the PCM and alternator. Start the engine and monitor the VT wire for a roughly 0-10v square wave signal. The signal will be around 40-50% normally with no loads on the system and minimal charging system output.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

2000-2003 FORD Focus AEM Induction System PART NUMBER: 21-450

DownloadPART NUMBER: 21-450 2000-2003 FORD Focus L4-2.0L C.A.R.B. E.O. # D-670. The AEM® intake system is a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must return your vehicle to stock OEM air box and intake tract configuration. Failure to follow these instructions will void your warranty. 1. Preparing Vehicle a. Make sure vehicle is parked on level surface. b. Set parking brake. c. If engine has run in the past two hours, let it cool down. d. Remove the battery cover and disconnect negative battery terminal. e. Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle. Support your vehicle using properly rated jack stands before wheel removal or while working under the vehicle. NEVER WORK UNDER A VEHICLE WITHOUT USING JACK STANDS. i. Remove the lower front splashguard.… Read More

2000-UP FORD FOCUS ZETEC PERFORMER EFI SERIES NITROUS SYSTEM

Download EDELBROCK NITROUS SYSTEMS 2000 & LATER FORD FOCUS ZETEC PERFORMER EFI SERIES NITROUS SYSTEM Part Number 70408 INSTALLATION AND OPERATION INSTRUCTIONS. Nitrous Bottle Installation After you have determined the location and orientation of the nitrous bottle, use the procedure to install the bottle: Street Car Installations 1. Disconnect vehicle’s battery. 2. Determine the location of the bottle within the confines of the rear of the vehicle. 3. Once a mounting location has been determined, raise the vehicle (f safety practices involved in working on a vehicle from under the vehicle) and verify fuel tank(s), brake lines, emissions equipment, or structural members in the way of potential mounting bolt locations. : It may be necessary to remove the fuel tank depending on the location 4. Install the rubber insulators within the bottle brackets. 5. Slip bottle into the mounting brackets. 6. Using the mounting bracket bolt holes as templates, mark an area for each of the brackets with chalk, metal marking pen, scribe, or marking pen to locate the bolt 7.… Read More

2000 – 2003 FORD FOCUS 1 LAKEWOOD TRACTION BARS #50200 INSTALLATION INSTRUCTIONS

Download 1. Raise the front of the vehicle with a floor jack or lift (lift is preferred) and then support the suspension under the A-arms with jack stands. CAUTION! DO NOT BEGIN THIS INSTALLATION UNTIL YOU ARE CONFIDENT THAT THE VEHICLE IS SECURE AND SAFELY SUPPORTED! 2. From the top of the vehicle using the two 5/16″ x 2″ hex bolts with the 5/16″ fender washers supplied locate the top radiator mounts. Thread the bolts into the mounts until they touch the core support, this will hold the radiator up while you are removing the front Lower Radiator Cradle. Remove horn and any wiring that is attached to the old front Radiator Cradle. Next, remove the four bolts that fasten the radiator cradle to the frame using a 10mm socket. Unbolt and remove the cradle from vehicle (Disconnect wire clips on plastic shields if needed) and set cradle aside. This will no longer be needed while using Lakewood Traction Bars.… Read More

2005-2009 Ford Focus WHITE FLAKES COMING FROM A/C VENTS

Download FORD: 2007-2009 MKX 2005-2009 Focus 2008-2010 Crown Victoria MERCURY: 2000-2005 Expedition, F-150 2008-2010 Grand Marquis, Mariner Hybrid, 2007-2009 Edge Mariner 2008-2010 Escape Hybrid, Escape LINCOLN: 2008-2010 Town Car 2000-2005 Navigator. This article supersedes TSB 9-19-16 to update the Using compressed air (maximum inlet pressure) 100 Service Procedure. PSI (689 kPa), clean the A/C ducts through the registers and blow off the evaporator core through ISSUE the blower motor opening. Some vehicles may experience white flakes coming NOTE from the A/C vents when the blower motor is THE ENTIRE EVAPORATOR CORE SURFACE engaged. This may be caused by flux utilized in the MUST BE DRY FOR BEST RESULTS. manufacturing process of the evaporator core. NOTE ACTION WHILE PERFORMING THIS PROCEDURE AND Follow the Service Procedure steps to correct the SELECTING DIFFERENT VENT MODES SUCH AS condition. FLOOR / PANEL AND FLOOR / DEFROST, IT SERVICE PROCEDURE MAY BE NECESSARY TO TEMPORARILY START THE ENGINE TO ENABLE MODE DOOR Hazard and Risk Warnings for White Flakes MOVEMENT.… Read More

2.0L FORD FOCUS Supercharger System Installation Instructions

Download 2.0L FORD FOCUS Supercharger System Installation Instructions 2000-2003 ZX3 Model 2002-2003 SVT Model. A. Remove the ducting between the air box and the throttle body. Disconnect the MAF from the ducting and set aside. B. Remove the air box, fresh air tube, battery, battery box and all remaining components running to the inlet of the motor. C. Remove the Battery/Air Box support bracket: 1. Support the driver’s side of the transmis- sion. 2. Remove four nuts securing the bracket to the driver’s side engine mount. 3. Remove the large central nut securing the transmission to the engine mount. 4. Lift the plate on top of the engine mount and remove the Battery/Air Box support bracket. (See Fig. 1-a .) 5 . Reinstall the engine mount plate and resecure all engine mount hardware. D. Place an oil drain pan beneath the power steering pump. Disconnect the high-pressure (3/8″ tube) power steering line from the power steering pump.… Read More