Download 1996-Up Audi / Volkswagen Bose Integration Harness For models amplified without Bose: 1996-03 Audi A4 / 1996-03 Audi A6 2000-01 Audi S4 / 2002-03 Audi S6 Use the White, White/Black, Gray, and Gray/Black speaker wire for the front speaker output and use the Green and Purple RCA’s for the rear speaker outputs. Be sure to connect the Blue/White wire to the aftermarket radio’s amp turn-on wire. The White and Gray RCA’s will not be used. For models amplified with Bose: 1996-03 Audi A4 / 1996-03 Audi A6 1997-03 Audi A8 / 2000-01 Audi S4 2002-03 Audi S6 / 2001-03 Audi S8 2000-03 Audi TT Use the White and Gray RCA’s for the front speaker output and use the Green and Purple RCA’s for the rear speaker outputs. Be sure to connect the Blue/White wire to the aftermarket radio’s amp turn-on wire. The White, White/Black, Gray, and Gray/Black speaker wires will not be used.… Read More
2000 Audi A6 Bose Amp Wiring Diagram
I am considering upgrading the Bose sound system in the 2009 Q7. Was wondering if any of you would be able to tell me the speaker sizes for front and.
i have a 2000 audi a6 2.7 and im wiring an amp and subwoofer. ive been reading up that you can splice the rca’s off of the stock amp.. i know what wires are the.
Radio Mounting Kits and Phone Mounts for 2003 AUDI A6 Make your car stereo look like factory installed with a dash kit.
Filed Under (Audi) by Doe Namblas on 10-12-2013
Download Audi RS4 Quattro 2.7L V6 ‘Bi-Turbo’ Apr’00- 1. Disconnect the negative terminal from the battery. 2. Remove the plastic cover from the air box assembly. (Fig. 1) 3. Remove the air box feed pipe from between the air box lid & slam panel intake scoop. (Fig. 2) 4. Unclip & remove the electrical harness plug from the MAS (Mass Air Sensor). (Fig. 3) 5. Unclip & remove the intake hose from the MAS. (Fig. 4) 6. Unclip the 3 hoses from the top of the air box assembly. (Fig. 5) 7. Unbolt & remove the two ignition amplifiers from the top of the air box lid. (Fig. 6) 8. Unclip & remove the air box lid & filter from the vehicle. (Fig. 7) 9. Remove the small vacuum tube from the hose located at the base of the air box assembly. (Fig. 8) 10. Remove the bolt securing the air box assembly to the inner wing & carefully remove the assembly from the vehicle.… Read More
Filed Under (Honda) by Doe Namblas on 17-12-2013
Download IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)Fuse & Circuit Breaker Identification z 1 – 60 Amp Power Distribution z 2 – 50 Amp Dash Fuse Box z 3 – 40 Amp Dash Fuse Box, Exterior Lighting z 4 – 10 Amp PGM-FI Electronic Control Unit, Hazard Lights, A/T Control Unit (Wagon), Integrated Control Unit (1990), Automatic Shoulder Belts (1990) z 5 – 15 Amp Horns, Brakelights, A/T Control Unit (Wagon Only), Key Interlock Solenoid (A/T Only), Seat Belt Retractors (1990) z 6 – 20 Amp Rear Window Defogger z 7 – 15 Amp PGM-FI Main Relay z 8 – 15 Amp A/C Compressor Clutch, Condenser Fan Relay… Read More
Filed Under (Audi) by Doe Namblas on 12-10-2013
Download 1. Disconnect the negative terminal from the battery. 2. Unclip & remove the electrical harness plug from the MAS (Mass Air Sensor). (Fig. 1) 3. Unclip & remove the intake hose from the MAS. (Fig. 2&3) 4. Remove the air box feed pipe from between the air box lid & slam panel intake scoop. (Fig. 4) 5. Remove the small vacuum hose from the base of the air box assembly. (Fig. 5) 6. Remove the clip securing air box assembly to inner wing & carefully remove the assembly from the vehicle. (Fig. 6&7) 7. Undo the two nuts & remove the electrical unit to give access to the front suspension strut bolt as shown. (Fig. 8) 8. Remove the front bolt securing the suspension strut to the turret as shown. (Fig. 9) 9. Assemble the saddle bracket / twist ‘L’ mounting bracket using the allen head bolt, nylon conical washer, flat metal washer & nylock nut supplied.… Read More
Filed Under (Other Manuals) by Doe Namblas on 02-01-2014
Download Citroen C4 1.6Hdi 2004-2009, Citroen Berlingo 1.6L 2005-2009, Citroen C2 1.6Hdi 2005-2009, Citroen C3 1.6Hdi 2008-2009, Citroen C3 Picasso 1.6Hdi 2009, Citroen C4 Picasso 1.6Hdi 2006-2009, Citroen C5 1.6Hdi 2005-2009, Mini Cooper 1.6Hdi 2007-2009, Mini Cooper Clubman 1.6Hdi 2007-2009, Peugeot 207 1.6 2006-2009, Peugeot 308 1.6 2007-2009, Peugeot 407 1.6 2005-2009, Peugeot Partner 1.6 2006-2009.
Parts list: 1 x Air filter Element. 1 x Silicone Intake Hose. 1 x Flexi Cold Air Hose. 1 x Metal Adaptor Hose. 1 x Literature Pack. Fixing Kit :- 3 x Plastic Tie. 3 x #44 Hose Clamp. 1 x Mounting Bracket. 1 x M6 Nylock Nut. 2 x M6 Flat Washer. 1 x Hex Head Bolt M6x20.
Instruction sheet A2054-768 1. Disconnect the negative terminal from the vehicle battery. 2. To the install induction kit it is necessary to remove the bulkhead trims: 3. Unclip & remove the side cover surrounding the washer bottle etc.… Read More
Download AUDI A4 – 2000-2002 AUDI S4 – 2000-2002 AUDI A6 – 2000-2005 AUDI-ALLROAD – 2000-2005 Mount Location: To the Right of the Radio. Multi Vehicle Mount MVM-45-05 Includes PHS-203 Ultra Slim Swivel. DASH DISASSEMBLY INSTRUCTION Locate the four slots on the face of the radio. Insert the Audi DIN tools in these four slots until you hear a click or lock. Note: There is a rubber seal that wraps around the radio between the radio and the dash pad. This causes the radio to sit very tightly in the cavity. To loosen this seal and allow the radio to slide out easier, we recommend using a Dash Trim Tool to wedge between both the right and left sides of the radio dash pad. Carefully wiggle the tool to loosen the radio slightly. Grasp the four DIN tools and slide the radio out of its cavity just enough to allow access to the one (1) 5/16″ hex head bolt that holds the climate control in place.… Read More
Download AUDI A4, S4, QUATTRO (2000-2002) AUDI A6 QUATTRO (2000-2003) AUDI ALLROAD QUATTRO (2001-2003). NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT . All phone mount instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.TOOLS NEEDED: Two (2) sets of Audi DIN Radio Removal Tools, (Btron Part # SIT-102 One (1) Flat Headed Screwdriver or Dash Trim Tool (Btron Part # SIT-104), 5/16″ socket and driver . PARTS INCLUDED: One phone mount and instructions. LOCATION OF MOUNT: To the Right of the Radio. Installation Instructions 1. Locate four slots on the face of the radio. Insert four Audi DIN tools in these four slots until you hear or feel the tools click or lock. Note: There is a rubber seal that wraps around the radio between the radio and the dash pad.… Read More
Filed Under (Audi) by Doe Namblas on 01-01-2014
Download 2000 Audi A4 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ, USA/Canada 2000 Audi A6 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ Customer Concern: MIL on, DTC P0130 – 16514 – oxygen sensor Bank 1 sensor 1 malfunction; P0150 – 16534 – oxygen sensor Bank 2 sensor 1 malfunction. Engine has extended crank time after sitting for more than a few hours. Tests/Procedures: 1. Trouble Code P0130 (16514) indicates an electrical malfunction with the Bank1, Sensor 1 Oxygen Sensor (O2). Connect a full function Audi compatible scan tool. Enter address menu 01 “Engine Electronics”. Enter functions menu 08 “Read Measuring Value Block”. Enter display group 041. Check specified values in fields 1. Field 1 displays Oxygen Sensor (O2) Bank 1, Sensor 1 (B1S1) heater circuit resistance. Specification is 0.0 to 0.9 Kohm. Note: If the O2′s have not yet reached their operating temperature, there will be no indication in display field 1.… Read More
Filed Under (Ford) by Doe Namblas on 26-04-2013
Download 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. INTERIOR FUSE PANEL IDENTIFICATION (1994-95 MODELS) On all models, the fuse panel is located under the instrument panel, left of the steering column. Fuse & Circuit Breaker Identification 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module 10 – 10 Amp OBD-II Test Connector 11 – Not Used 12 – 5 Amp Illumination Of: Cluster, Phone Switch, Rear Defrost Switch, A/C Switch (Manual), PRNDL Indicator, Ashtray, EATC, Clock, Radio 13 – 20 Amp Cigarette Lighter, Flash-To-Pass 14 – 15 Amp Speed Control Module, ABS Module, BrakeShift Interlock, High Mount Brakelight, Brakelights, Flashers 15 – 5 Amp Cluster (Gauges), Cluster (ABS & Airbag Warning), Warning Chime, Autolight Sensor 16 – 10 Amp Integrated Module, Sport Voltmeter, Speed Control, Remote Keyless Entry, Anti-Theft, Power Window/Door Lock Switch Illumination, Radio, CD Changer, Power Antenna, Clock 17 – 30 Amp Wiper/Washer System 18 – 20 Amp Power Door Locks, Decklid Release, Fuel Door Release, Power Seats, Power Lumbar, Booster 19 – 20 Amp Power Window Motors, Moon Roof Motor UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron.… Read More
Download VW*Passat*B5*from*1997-2000; * Audi*A4*from*1995-2000 P3740,*C3740 Replacement interval 15.000 km/10,000 miles or after 12 months Intervalo de cambio 15.000 km o despues de 1 año Intervalle de remplacement 15.000 km ou une fois par an Assembly is the reverse order of operation Para concluir la instalacion, seguir el orden inverso Le remontage s’effectue dons l’ordre inverse Tools needed are a Phillips screwdriver. Open the hood. Notice the cover for the cabin filter is on the cowl on the passenger side. Remove the screw form the cover. Remove the cover by pulling toward the front of the vehicle. The filter is now visible. Remove by pushing up on the filter to loosen from housing and then pulling out toward the front of the vehicle. Replace with clean cabin filter. Replace cover by lining up the notches on either side of the cover plate to the grooves in the filter housing. Replace the screw in the cover plate.… Read More