1999 infiniti i30 security system reset

You search Auto repair manual PDF about 1999 infiniti i30 security system reset, search results will appear below. If search results do not exist, please search by others keyword.

1997 – 2001 Infiniti Q45 ENGINE WILL NOT START

Filed Under (Infiniti) by admin on 24-12-2013

Download 2000 – 2001 I30 (CA33) 1999 I30 (CA32) 1999.5 – 2001 QX4 (JR50) 1997 – 2001 Q45 (FY33) 2000 – 2001 G20 (P11) APPLIED VINS: All APPLIED DATES: Start of production SERVICE INFORMATION This bulletin describes and introduces new features of the Infiniti Vehicle Immobilizer System/Nissan Anti-Theft System (IVIS/NATS). The system is standard equipment on each of the applied vehicles listed above. The IVIS/NATS will not allow the engine to start without the use of a registered ignition key. If a vehicle will not start and the Security lamp is on solid, it may be because the ignition keys were not properly registered into the vehicle’s NATS IMMU (Immobilizer control unit). In this case, there will be a “DIFFERENCE OF KEY” code stored in the NATS IMMU. When the NATS ignition key, IMMU, or ECM (ECCS control unit) are replaced, C/U initialization is necessary. It is also necessary when registering keys and as part of many NATS Service Manual diagnostic procedures.… Read More

1999-2001 Infiniti Q45 (FY33) MIL “ON” REAR O2 SENSOR DTC

Filed Under (Infiniti) by admin on 10-01-2014

Download 1999-2001 Q45 (FY33) SERVICE INFORMATION If a 1999, 2000, or 2001 Q45 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) • P0158 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Max. Voltage Monitoring) • P0159 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Response Monitoring) • P0160 Heated Oxygen Sensor 2 (Rear) (Bank 2) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies.… Read More

Clunk, Bump or Squawk when Vehicle Comes to Complete Stop

Filed Under (Other Manuals) by admin on 02-04-2014

Download 1999-2000 Cadillac Escalade (Old Style) 2002-2004 Cadillac Escalade, Escalade EXT 2003-2004 Cadillac Escalade ESV 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 Chevrolet Silverado 2500 Series Crew Cab, Short Box (New Style) 1996-1999 GMC 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 GMC 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 GMC Sierra Extended Cab Short Box (New Style) 1999-2004 GMC Sierra 1500 Series Regular Cab (New Style) 2000-2004 GMC 1500 Series Yukon, Yukon XL 2001-2004 GMC Sierra 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) 2003-2005 HUMMER H2 with Four Wheel Drive (4WD) or All Wheel Drive (AWD) and One-Piece Propeller Shaft ONLY.… Read More

2008 Ford Super Duty F-Series Accessories List DESCRIPTION

Filed Under (Ford) by admin on 18-03-2014

Download “Mobile-ease™” Hands Free System Connector Wiring Harness Required for Installation of “Mobile-ease™” Hands Free System 3W4Z-14A411-AA 2005-2008 Hands Free System Requires Connector Harness 14A411 for Installation3W4Z-19G399-AA2005-2008 Bed Hooks, Retractable Stainless Steel XC3Z-99000A64-AA 2000-2008 Black E-Coat XC3Z-99000A64-BA 2000-2008 Bed Mats Long Bed, Styleside, With Ford Logo F81Z-99112A15-AA 1999-2008 Short Bed, Styleside, With Ford Logo F81Z-99112A15-BA 1999-2008 Bed Rail Caps, Diamond Plate Short Bed, With Stake Pocket Holes F81Z-99291A40-CAA 1999-2008 Long Bed, With Stake Pocket Holes F81Z-99291A40-DAA 1999-2008 Bedliner/Bedmat Tailgate Cover F75Z-99000A38-AA 1999-2008 Bedliners** With Ford Logo For Styleside 8.0′ Bed F81Z-9900038-AA 1999-2008 For Styleside 6.5′ Bed F81Z-9900038-BA 1999-2008 Bug Shield Low Profile Smoke-Color (Single-Pack) 8C3Z-16C900-A 2008 Smoke-Color (Bulk Pack of 10) 8C3Z-16C900-B 2008 Smoke-Color (Bulk Pack of 25) 8C3Z-16C900-C 2008 Mini Chrome-Color (Single-Pack) 8C3Z-16C900-D 2008 Chrome-Color (Bulk Pack of 10) 8C3Z-16C900-E 2008 Chrome-Color (Bulk Pack of 25) 8C3Z-16C900-F 2008. Deflectors, Side Window Crew Cab 4-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-CA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-HA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-JA 1999-2008 Regular Cab 2-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-AA 1999-2008 2-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-BA 1999-2008 2-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-CA 1999-2008 Super Cab 4-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-BA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-EA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-FA 1999-2008 Floor Mats, All Weather Molded Vinyl Front & Rear, 3-Piece Set, Front With Vehicle Logo Super Cab, Ebony 8C3Z-2613300-B 2008 Crew Cab, Ebony 6C3Z-2813300-A 2002-2008 Front Pair, With Vehicle Logo Reg.… Read More

1100F FORD PATS / SECURILOCK REMOTE START INTERFACE-DATA

Filed Under (Ford) by admin on 31-12-2013

Download PRODUCT ACCESSORIES DESCRIPTION The 1100F interface module is used when installing remote start products in Ford vehicles equipped with a factory immobilizer. The 1100F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. The factory transponder-based anti-theft system uses a small electronic chip hidden in the key to send a code to the vehicle’s transceiver when the ignition is energized. The key must be placed in the ignition and turned to the RUN position. This energizes a coil surrounding the key, which in turn energizes the chip, which sends a code to the vehicle. If the vehicle does not detect the code being sent, the vehicle will start and then immediately shut off or will just crank, and the anti-theft light will flash. The 1100F provides a valid code to the vehicle whenever it is remote started, but does not affect the immobilizer system during normal vehicle operation; the immobilizer system remains fully functional.… Read More

2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Filed Under (Infiniti) by admin on 16-12-2013

Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More

Information on Error Codes on Radio Display – Their Cause and Corrective Action

Filed Under (Other Manuals) by admin on 25-12-2013

Download odels: 1995-1996 Buick Roadmaster 1995-1999 Buick LeSabre 1995-2004 Buick Century, Regal 1995-2005 Buick Park Avenue 1996-1999 Buick Riviera, Skylark 2004-2005 Buick Rainier 1995-1999 Chevrolet Lumina, Monte Carlo, Fullsize Pickup Models (Old Style) 1995-2005 Chevrolet Blazer 1996 Chevrolet Lumina APV 1996-1999 Chevrolet Cavalier 1996-2000 Chevrolet Express Van 1996-2002 Chevrolet Astro Van 1997-2002 Chevrolet Camaro 1997-2003 Chevrolet Malibu 1997-2005 Chevrolet Corvette, Venture 2000-2005 Chevrolet Silverado 2002-2005 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2005 Chevrolet SSR 2004-2005 Chevrolet Classic, Colorado 1995-1999 GMC Fullsize Pickup Models (Old Style) 1995-2002 GMC Jimmy 1996-2000 GMC Savana Van 1996-2002 GMC Safari Van 2000-2005 GMC Sierra 2002-2005 GMC Envoy, Envoy XL 2004-2005 GMC Canyon, Envoy XUV 1995-1999 Oldsmobile Aurora, Eighty Eight 1995-1997 Oldsmobile Cutlass Supreme 1999-2004 Oldsmobile Alero 1998-2002 Oldsmobile Intrigue 1995-1996 Oldsmobile Ninety Eight 1996-1999 Oldsmobile Achieva 1996-2004 Oldsmobile Bravada, Silhouette 1995-1999 Pontiac Bonneville, Sunfire 1995-2002 Pontiac Firebird 1995-2005 Pontiac Grand Prix 1996-1997 Pontiac Trans Sport 1996-2000 Pontiac Grand Am 1997-2005 Pontiac Montana 2003-2005 HUMMER H2.… Read More

1999 Ford EXPLORER TRANSMISSION SLIPPING SHIFT/DELAYED

Filed Under (Ford) by admin on 02-04-2014

Download FORD: 1999 EXPLORER, RANGER MERCURY: 1999 MOUNTAINEER 6. Inspect the fluid pan for major contamination. ISSUE Slipping transmission shifts and/or delayed or no •If contamination is minimal, clean the main transmission engagements may occur on some control, but do not replace. vehicles. The Electronic Pressure Control (EPC) •If major contamination is present, perform solenoid may cause stress on the attaching bracket. normal transmission overhaul as required, This stress causes the bracket to break and the including main control replacement. Pay EPC solenoid to back out of its bore causing line particular attention to the condition of the pressure to drop too low or fluctuate, allowing friction plates. Repair as required. friction clutches to slip. 7. After repairs are completed, verify concern has ACTION been fixed. Diagnose and inspect for damaged EPC attachment PART NUMBER PART NAME bracket, and replace the bracket and EPC solenoid with new bracket and revised EPC solenoid.… Read More

Acura 2.3CL and 3.0CL Security System Installation Notes

Filed Under (Acura) by admin on 31-01-2014

Download Locate the Keyless Security Control unit underneath the passenger seat and refer to the 2 connector illustrations below to make your connection. Connector A: A1: Ignition A2: Interior light (Supervision) A3: Door Actuator (Motor) A4: Trunk Actuator (|Motor) A5: Door Actuator (Motor) A6: Starter Cut Relay A7: Security Indicator A8: Siren Out (-) A9: Door Actuator (Motor) A10: Ground A11: Light Flash Out (+) (Parking) A12: Battery 12v+ Input Connector B: B1: Hood switch B7: Lock &(Alarm Arm) Pass sideB13: Not used B2: Unlock Input (-) B8: Lock &(Alarm Arm) Driver sideB14: Not Used B3: Unlock Input (-) B9: Trunk Latch Input (-) B15: Not Used B4: Not Used B10 Key In Ignition (Neg input) B16: Light Flash Out (+) Head. B5: Unlock Input (-) B11: Lock Input (-) B17: Unlock Input & (Alarm dis.) B6: Lock Input (-) B12: Door Ind (Instrument cluster) B18: Start Input (12v in Crank)… Read More

1998 Buick Park Avenue Engine Coolant Consumption or Coolant Leak

Filed Under (Buick) by admin on 20-01-2014

Download Engine Coolant Consumption or Coolant Leak (Inspect For Material Degradation/Replace Intake Manifolds) Models: 1995-1997 Buick Riviera 1995-1999 Buick LeSabre, Park Avenue 1996-1999 Buick Regal 1998-1999 Chevrolet Lumina, Monte Carlo 1995-1996 Oldsmobile Ninety-Eight 1995-1999 Oldsmobile Eighty-Eight 1998-1999 Oldsmobile Intrigue 1995-1999 Pontiac Bonneville 1997-1999 Pontiac Grand Prix with 3.8L Engine (VIN K — RPO L36) Condition Some customers may comment on excessive engine coolant consumption, or an engine coolant leak near or under the throttle body area of the upper intake manifold. Cause Upper intake manifold composite material may degrade around the EGR stove pipe and could result in an internal or external coolant leak. Correction 1. Follow the upper intake manifold removal instructions found in the Engine Unit Repair Section of the Service Information Manual. 2. Refer to the arrow in the illustration of the upper intake manifold above. Inspect the inner diameter of the EGR passage for signs of material degradation.… Read More

You might also likeclose