1999 honda civic evap diagram

You search Auto repair manual PDF about 1999 honda civic evap diagram, search results will appear below. If search results do not exist, please search by others keyword.

Honda Civic D-series Racing Intake Manifold Manual Installation Instructions

Filed Under (Honda) by admin on 01-01-2014

Download
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Filed Under (Honda) by admin on 01-01-2014

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More

2007 Honda Accord CR-V and Civic Remote Engine Starter FAQ

Filed Under (Honda) by admin on 02-01-2014

Download
Model Information Release date for Accord Remote Starter System: September 20, 2007 Release date for CR-V and Civic Remote Starter System: End of September 2007 Technical Questions Q: What does the Honda Remote Engine Starter System do? A: The Honda Remote Engine Starter is a two-way remote system that starts and stops your vehicle’s engine anywhere within a 200-foot range. It’s designed to warm up your vehicle in the winter and cool it down in the summer. Q: How much is the Honda Remote Engine Starter? A: Approximately $499.00 without installation for all applicable Honda models. Check with your Honda dealer for the installation cost. Q: Can I install it myself? A: AHM does not recommend that customers install the Honda Remote Engine Starter due to the complexity of its electrical components. Authorized Honda Technicians are professionally trained to safely install the Remote Engine Starter. Q: Can I have my neighborhood audio shop install the Honda Remote Engine Starter?… Read More

1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions

Filed Under (Honda) by admin on 27-02-2014

Download
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More

Honda/Acura Engine Management System (EMS) Manual Installation Instructions

Filed Under (Acura) by admin on 03-04-2014

Download
Vehicle: 2000-2001 Acura Integra, 1998-1999 Acura 2.3CL, 1996-2000 Honda Civic.
Engine wiring harness: 1999-2002 Honda Accord V6 J30A1, 1999 Acura CL 3.0L J30A, 2001-2003 Acura CL 3.2L J32A1 (auto harness only), 1999-2003 Acura TL 3.2L J32A1, 2002-2003 Acura CL/TL 3.2L Type S J32A2 (auto harness only), 2002-2004 Honda Odyssey 3.5L J35A4.
The AEM Engine Management System (EMS) is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM EMS differs from all others in several ways. The EMS is a stand alone system, which completely replaces the factory ECU and features unique Plug and Play Technology, which means that each system is configured especially for your make and model of car without any jumper harnesses. There is no need to modify your factory wiring harness and in most cases your car may be returned to stock in a matter of minutes.… Read More

1997-2001 Acura Integra Type-R Racing Intake Manifold

Filed Under (Acura) by admin on 03-01-2014

Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More

1999-2000 Honda 1.6L DOHC Civic Si VORTECH Supercharger System Installation Instructions

Filed Under (Honda) by admin on 22-02-2014

Download For best performance and continued durability, please take note of the following key points: 1. Use only premium grade fuel 92 octane or higher (R+M/2). 2. The engine must have stock compression ratio. 3. If the engine has been modified in any way, check with Vortech prior to using this product. 4. Always listen for any sign of detonation (pinging) and discontinue hard use (no boost) until problem is resolved. 5. Perform an oil and filter change upon completion of this installation and prior to test driving your vehicle. Thereafter, always use a high grade SF rated engine oil or a high quality synthetic, and change the oil and filter every 3,000 miles or less. Never attempt to extend the oil change interval beyond 3,000 miles, regardless of oil manufacturer’s claims as potential damage to the supercharger may result. 6. Before beginning installation, replace all spark plugs that are older than 1 year or 10,000 miles with original heat range plugs as specified by the manufacturer and retard timing from factory specifications (follow the procedures indicated within the factory repair manual and/or as indicated on the factory underhood emissions tag).… Read More

Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit

Filed Under (Other Manuals) by admin on 15-01-2014

Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More

1999-2000 Honda Civic Si B16A2 Supercharger System Manual Installation Instructions

Filed Under (Honda) by admin on 03-12-2013

Download
TOOLS NEEDED : 8, 10, 12, 14, 17, and 22-mm socket and wrenches, and an 11-mm (7/16″) socket or wrench, 8- mm Allen wrench, Phillips and straight blade screwdrivers, vice grip pliers, a drill, a 5/8″ drill bit, and a timing light. You will also need an electric or air impact gun to remove the alternator pulley (using the 22-mm socket). Most of these tools are available at your local hardware or auto parts store. Jackson Racing Supercharger Systems are designed to be installed by individuals with good mechanical sense and with the proper tools.
INSTALLATION INSTRUCTIONS
1. VERY IMPORTANT! Remove the negative battery cable. If you have a coded alarm on your radio, retrieve the code before removing the negative cable. On our test vehicle, both the alarm and radio codes were on a card received at vehicle purchase. Removing the negative cable shuts down the entire electrical system and is the safest way to work on your vehicle.… Read More

1999-2000 Honda Civic Si Supercharger System Manual Installation Instructions

Filed Under (Honda) by admin on 25-03-2014

Download
TOOLS NEEDED : 8, 10, 12, 14, 17, and 22-mm socket and wrenches, and an 11-mm (7/16″) socket or wrench, 8- mm Allen wrench, Phillips and straight blade screwdrivers, vice grip pliers, a drill, a 5/8″ drill bit, and a timing light. You will also need an electric or air impact gun to remove the alternator pulley (using the 22-mm socket). Most of these tools are available at your local hardware or auto parts store.
INSTALLATION INSTRUCTIONS : 1. VERY IMPORTANT! Remove the negative battery cable. If you have a coded alarm on your radio, retrieve the code before removing the negative cable. On our test vehicle, both the alarm and radio codes were on a card received at vehicle purchase. Removing the negative cable shuts down the entire electrical system and is the safest way to work on your vehicle. But, you will lose all of your preset radio stations and alarm codes.… Read More

You might also likeclose