1999 grand am how to test wheel speed sensor

You search Auto repair manual PDF about 1999 grand am how to test wheel speed sensor, search results will appear below. If search results do not exist, please search by others keyword.

1999 Pontiac Grand Am SE RIGHT FRONT WHEEL SPEED SENSOR CIRCUIT OPEN OR SHORTED

Filed Under (Pontiac) by admin on 27-01-2014

Download 1999 Pontiac Grand Am SE 1998-99 BRAKES Anti-Lock/TCS – ABS-VI – Cars. DTC C1233: RIGHT FRONT WHEEL SPEED SENSOR CIRCUIT OPEN OR SHORTED 1. Perform diagnostic system check. See DIAGNOSTIC SYSTEM CHECK. After performing diagnostic system check, go to next step. 2. Turn ignition off. Spray right front wheel speed sensor jumper harness thoroughly with a 5 percent saltwater solution (2 teaspoons of salt to 12 ounces of water). Disconnect EBCM/EBTCM connector C1 (“W” body), connector C2 (“J” body, Cutlass and Malibu) or 32-pin connector (Achieva, Alero, Grand Am and Skylark). See EBCM/EBTCM LOCATION under REMOVAL & INSTALLATION. Using DVOM, measure resistance between speed sensor signal high circuit and speed sensor signal low circuit of EBCM/EBTCM connector. On “W” body, resistance should be 1020-1137 ohms at 68°F (20°C). On “J” body, Achieva, 1998 Grand Am and Skylark, resistance should be 1530-1870 ohms at 68°F (20°C). On Alero, Cutlass, 1999 Grand Am and Malibu, resistance should be 950-1250 ohms at 68°F (20°C).… Read More

2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR

Filed Under (Ford) by admin on 14-02-2014

Download SELF-DIAGNOSTICS – EEC-V (DIESEL) -2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR. Perform this test when directed by QUICK TEST. This test is intended to diagnose: Exhaust Backpressure (EBP) Sensor • Wiring Harness Circuits (SIG RTN, VREF & EBP Signal) • Powertrain Control Module (PCM) • 1) DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine.… Read More

Service 4WD Light Illuminated, DTC C0374 Set (Inspect Wiring Harness to Transfer Case Speed Sensors, Replace Wiring Harness)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2007 Buick Rainier 2003-2006 Chevrolet Avalanche, Suburban, Tahoe 2003-2007 Chevrolet Silverado Classic, TrailBlazer, TrailBlazer EXT 2003-2006 GMC Yukon, Yukon XL 2003-2007 GMC Envoy, Envoy XL, Sierra Classic 2003-2004 Oldsmobile Bravada 2005-2007 Saab 9-7X with Four Wheel Drive or All-Wheel Drive and Active All-Wheel Drive (RPO NP4) or Active Two-Speed (RPO NP8) Transfer Case. Condition Some customers may comment on intermittent illumination of the Service 4WD light. Upon investigation, the technician may find DTC C0374 set. The customer may also comment on intermittent erratic operation of the 4WD or AWD system after driving through rain/snow or simply going through a car wash. Cause The speed sensor signal may have become corrupted. Possible openings in the speed sensor wire insulation (twisted pairs) can allow water intrusion. Also, wire connections contaminated by water may result in short circuits and erroneous speed sensor readings. This most often occurs on the rear speed sensor circuit.… Read More

2000 Audi A4 Quattro oxygen sensor Bank 1 sensor 1 malfunction

Filed Under (Audi) by admin on 01-01-2014

Download 2000 Audi A4 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ, USA/Canada 2000 Audi A6 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ Customer Concern: MIL on, DTC P0130 – 16514 – oxygen sensor Bank 1 sensor 1 malfunction; P0150 – 16534 – oxygen sensor Bank 2 sensor 1 malfunction. Engine has extended crank time after sitting for more than a few hours. Tests/Procedures: 1. Trouble Code P0130 (16514) indicates an electrical malfunction with the Bank1, Sensor 1 Oxygen Sensor (O2). Connect a full function Audi compatible scan tool. Enter address menu 01 “Engine Electronics”. Enter functions menu 08 “Read Measuring Value Block”. Enter display group 041. Check specified values in fields 1. Field 1 displays Oxygen Sensor (O2) Bank 1, Sensor 1 (B1S1) heater circuit resistance. Specification is 0.0 to 0.9 Kohm. Note: If the O2′s have not yet reached their operating temperature, there will be no indication in display field 1.… Read More

2002 Crown Victoria/Grand Marquis Workshop Manual

Filed Under (Ford) by admin on 31-12-2013

Download Adjust the blower motor setting to LO and then to HI. * Does the blower motor operate correctly? Yes REPAIR circuit 515 (OG/RD) for a short to ground. TEST the system for normal operation. No GO to R2 . R2 CHECK THE BLOWER MOTOR SPEED CONTROL Blower Motor Speed Control C1308 EATC Module C228b * Does the blower motor operate? Yes INSTALL a new blower motor speed control. TEST the system for normal operation. No GO to R3 . R3 CHECK THE BLOWER MOTOR SPEED CONTROL CIRCUITS FOR AN OPEN Blower Motor Speed Control C1308 Measure the resistance between the blower motor speed control C1308: * pin 1, circuit 269 (LB/OG) and the EATC module C228b pin 10. * pin 2, circuit 752 (YE/RD) and the EATC module C228b pin 23. * pin 3, circuit 754 (LG/WH) and the EATC module C228b pin 24. * Are the resistances less than 5 ohms?… Read More

2009 Honda CR-V 17″ ALUMINUM WHEEL INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 15-12-2013

Download PARTS LIST Aluminum wheel (The illustration may differ from the actual wheel.) Wheel center cap (The illustration may differ from the actual center cap.) Center cap emblem 2 Push nuts Wheel cleaning information TPMS Information (Give this information to your customer.) Parts for TPMS sensor assembly Tire pressure sensor assembly Washer Valve cap Valve nut TOOLS AND SUPPLIES REQUIRED Ratchet wrench 11 mm Socket Torque wrench Isopropyl alcohol Shop towel HDS TPMS sensor initializer tool AKS0620006 INSTALLATION NOTE: •This aluminum wheel is designed for use on TPMS (Tire Pressure Monitoring System) vehicles. •This aluminum wheel is equipped with the TPMS sensor. See the Service Manual for tire replacement procedure and TPMS sensor installation procedure. •The illustration of the aluminum wheels shown are for reference purposes only. •Install the correct size tire. •Use a tire changer to remove and install the tires. Using a tire lever to remove and install the tires can damage the tire, the wheel, and the TPMS sensor.… Read More

2002 – 2007 Honda CB900F Install Guide for GPX-H01 Harness Kit

Filed Under (Honda) by admin on 19-11-2013

1. Locating the Speed Sensor coupler
Preparation:
- The ignition key should be in OFF position.
- Raise the rear wheel off the ground by using a stand.
Make sure the rear wheel spins freely.
- Remove the seat.
The Speed Sensor is usually located on the top of the gearbox and reads the revolution
of the countershaft.
The 3-pole speed sensor coupler is situated 10-30 cm (4″-12″) away from sensor.
The connector is usually accessible by raising the fuel tank or removing a side fairing.
If the speedometer is driven off the front wheel, the sensor coupler is usually in the
headlight bucket.
If in doubt, check the bike’s Service Manual or ask your dealer for the location of the
Speed Sensor coupler.
Confirmation:
Separate the Speed Sensor coupler (you might need to use a small flathead screwdriver
to get the coupler apart). Rotate the rear wheel while the ignition is on.… Read More

2001 Mercedes-Benz SLK320 Engine light is on with no acceleration

Filed Under (Mercedes-Benz) by admin on 26-11-2013

Download Vehicle Application: 2000 Mercedes-Benz ML320 3.2L 2001 Mercedes-Benz E320 3.2L 2001 Mercedes-Benz C240 2.6L 2001 Mercedes-Benz E320 4Matic 3.2L 2001 Mercedes-Benz C320 3.2L 2002 Mercedes-Benz ML320 3.2L Customer Concern: Engine light is on with no acceleration. Fault code is P0120. Tests/Procedures: 1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 2. If voltages are out of specification verify correct reference voltage to sensor by measuring between pins 6 (Black/White wire) and pin 1 (Blue/Grey wire) on pedal sensor connector. Voltage needs to be between 4.75 and 5.25 volts. 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value.… Read More

2002 Volvo XC70 Rear Wheel Hub Replacing

Filed Under (Volvo) by admin on 31-12-2013

Download 2002 Volvo XC70 L5-2.4L Turbo VIN 58 B5244T3 Vehicle Level Transmission and Drivetrain Drive Axles, Bearings and Joints Wheel Hub Service and Repair Rear Wheel Hub, Replacing. Special tools: 951 2050 Raise the car Remove the rear wheel the screw for the drive shaft / wheel hub. Removing the rear wheel hub. Remove the brake caliper mounting screws. Hang the caliper up with a piece of wire the locating pin for the brake disc the brake disc the ABS-cable holder the ABS sensor. Hang up the sensor using a piece of wire. Remove the spring strut from the lower control arm Note: the spring strut is slightly compressed. Remove the anti-roll bar from the upper control arm Use a Torx wrench as a counterhold so that the rubber boot is not damaged. Remove the tie rod from the wheel spindle. Angle the tie rod upwards so that the inner mounting for the control arm is exposed the screw holding the lower mounting for the control arm to the sub-frame.… Read More

1999-2001 Infiniti Q45 (FY33) MIL “ON” REAR O2 SENSOR DTC

Filed Under (Infiniti) by admin on 10-01-2014

Download 1999-2001 Q45 (FY33) SERVICE INFORMATION If a 1999, 2000, or 2001 Q45 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) • P0158 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Max. Voltage Monitoring) • P0159 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Response Monitoring) • P0160 Heated Oxygen Sensor 2 (Rear) (Bank 2) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies.… Read More

You might also likeclose