1998 chevy 1500 truck free repair manual download

You search Auto repair manual PDF about 1998 chevy 1500 truck free repair manual download, search results will appear below. If search results do not exist, please search by others keyword.

1994 Chevy Truck C 1500 Ignition – Timing Connector Location Change

Filed Under (Chevrolet (Chevy)) by admin on 07-02-2014

Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More

2005 Chevy Truck Silverado 1500 Blower Motor Resistor Replacement

Filed Under (Chevrolet (Chevy)) by admin on 09-12-2013

Download 2005 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Vehicle Level Heating and Air Conditioning Blower Motor Resistor Service and Repair Blower Motor Resistor Replacement. BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor. 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Filed Under (Chevrolet (Chevy)) by admin on 28-11-2013

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

2003 Chevy Truck TrailBlazer Service and Repair

Filed Under (Chevrolet (Chevy)) by admin on 16-02-2014

Download Transmission Oil Cooler Line Quick Connect Fitting Removal Procedure Important: The front and rear sections of the cooler lines can be serviced separately. Refer to the appropriate steps when servicing individual lines. Perform the following procedure when removing the cooler lines from the quick connect fittings. 1. Pull the plastic cap back from the quick connect fining and down along the cooler line about 5 cm (2 inch) . 2. Using a bent-tip screwdriver, pull on one of the open ends of the retaining ring in order to rotate the retaining ring around the quick connect fining until the retaining ring is out of position and can be completely removed. 3. Remove the retaining ring from the quick connect fitting. 4. Discard the retaining ring. 5. Pull the cooler line straight out from the quick connect fitting. Installation Procedure Important: * Do not reuse any of existing fittings if there is excessive corrosion.… Read More

1998 Chevrolet Truck C1500 Repair Information

Filed Under (Chevrolet (Chevy)) by admin on 10-12-2013

Download1988-94 Models See Figures 1 and 2 Remove the steering wheel. 1. Fig. Fig. 1: Installing the lock cylinder. Fig. Fig. 2: Ignition switch Remove the turn signal switch. It is not necessary to completely remove the switch from the column. Pull the switch rearward far enough to slip it over the end of the shaft, but do not pull the harness out of the column. 2. Turn the lock to Run. 3. If necessary, remove the ignition key. 4. If equipped, remove the buzzer switch assembly. 5. Remove the lock retaining screw and remove the lock cylinder. 6. WARNING If the retaining screw is dropped on removal, it may fall into the column, requiring complete disassembly of the column to retrieve the screw. To install: Rotate the key to the stop while holding onto the cylinder. 7. Push the lock all the way in. 8. Install the screw. Tighten the screw to 40 inch lbs.… Read More

REAR AXLE NOISE REPAIR

Filed Under (Other Manuals) by admin on 24-11-2013

Download FORD: LINCOLN: 1997-2005 Expedition, F-150 1998-2005 Navigator 2002-2005 Explorer 2003-2005 Aviator MERCURY: 2002-2005 Mountaineer This article supersedes TSB 05-12-6 to update the NOTE Service Kit and Service Procedure information. WHEN SERVICING THE REAR AXLE ON ANY 2002-2004 F-150, EXPEDITION, NAVIGATOR, ISSUE EXPLORER OR MOUNTAINEER BUILT BEFORE Some vehicles may exhibit an axle whine or hum 3/30/2004, IF FLUID REPLACEMENT IS during acceleration, deceleration and/or cruise. REQUIRED, REPLACE THE ORIGINAL FUEL EFFICIENT HIGH PERFORMANCE (FEHP) SAE ACTION 75W-90 REAR AXLE LUBRICANT WITH SAE An axle repair kit has been developed which 75W-140 HIGH PERFORMANCE SYNTHETIC incorporates most parts required for a REAR AXLE LUBRICANT. WHEN THE FLUID comprehensive axle repair. The kit should be used TYPE IS CHANGED, REPLACE THE CURRENT instead of installing a complete axle assembly to “FEHP” METAL TAG WITH A NEW “75W-140″ TAG repair an axle whine/hum. Replace Ring and Pinion (F3TZ-4121-AA). IN ADDITION, REMOVE OR with Axle Kit and Components.… Read More

1997 Chevy Truck C Tahoe Interior Lighting Module Locations

Filed Under (Chevrolet (Chevy)) by admin on 19-03-2014

Download 1997 Chevy Truck C Tahoe 2WD V8-5.7L VIN R View: Under Center Of Instrument Panel Zoom Sized for Print Interior Lamp Control Module, Remote Control Door Lock Receiver Manufacturer supplied 2 different possible locations. Look for 5 wire connector with wire colors: gray, white, orange, pink & black. #PIT3819: Location of Interior Lamp Control Module – keywords control dim dome electrical entry ground illumination inoperative keyless lens light remort resistor RKE short – (Dec 23, 2005) Subject: Location of Interior Lamp Control Module. Models: 1995-2000 Chevrolet C/K Trucks, Suburban and Tahoe 1995-2000 GMC Yukon and C/K Trucks Classic Body Style Only The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this P1. Condition/Concern When diagnosing a dome lamp concern on one of the vehicles listed above, you may be unable to locate the Interior Lamp Control Module that is called out in the Service Manual.… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

1996-1998 Civic HX With CVT Repair Instructions

Filed Under (Honda) by admin on 08-01-2014

Download REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly. 4. Place the transmission on a work bench with the flywheel housing facing upward. 5. Remove the ATF passage line holder from the flywheel housing. 6. Remove the flywheel housing (20 bolts).… Read More

1998 Pontiac Grand Prix Fuel Pump Resistor Service Manual

Filed Under (Pontiac) by admin on 31-12-2013

Download Subject: 01033 — Fuel Pump Resistor Models: 1997-1998 Buick Regal GS & Pontiac Grand Prix GTP with L67 3.8L V6 Engine (Located in the High Corrosion Provinces of Newfoundland, Nova Scotia, Prince Edward Island, New Brunswick, Quebec and Ontario) Condition General Motors has decided that all 1997-1998 Buick Regal GS and Pontiac Grand Prix GTP model vehicles equipped with L67 3.8L V6 engines, located in the high corrosion provinces of Newfoundland, Nova Scotia, Prince Edward Island, New Brunswick, Quebec and Ontario, may develop an electrical open in the fuel pump resistor. This condition prevents operation of the fuel pump and the engine will not run. Correction Dealers are to install a new resistor on the plenum with an aesthetic cover. Vehicles Involved Involved are all 1997-1998 Buick Regal GS and Pontiac Grand Prix GTP model vehicles equipped with L67 3.8L V6 engines and built within these VIN breakpoints: Year Division Model Plant From Through 1997 Buick W Oshawa 2 V1400025 V1482781 1998 Buick W Oshawa 2 W1400008 W1614345 1997 Pontiac W Fairfax VF200090 VF359094 1998 Pontiac W Fairfax WF200104 WF342330 Important: Dealers should confirm vehicle eligibility through GM Access Screen prior to beginning campaign repairs.… Read More

You might also likeclose