1998 chevrolet ignition key cylinder removal

You search Auto repair manual PDF about 1998 chevrolet ignition key cylinder removal, search results will appear below. If search results do not exist, please search by others keyword.

Ford-Toyota-Lexus 555F Interface Module Wiring Installation Instructions

Filed Under (Ford) by admin on 13-01-2014

Download The 555F interface module is used when installing remote start products in Ford, Toyota and Lexus vehicles equipped with factory immobilizers. The 555F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. WIRE CONNECTION GUIDE FOR FORDS RED (+)12V: Connect this wire to a fused (+)12V source. BLUE (-) ACTIVATION INPUT: Connect this wire to the (-) through activation output of the remote start system. 555FCAPSULE: The 555F capsule should be placed on the outside of the antenna ring as close to the ribbon cable as possible. LEARNING THE 555F CAPSULE FOR FORDS To program the 555F capsule for a Ford vehicle, use the procedure that corresponds to the appropriate vehicle year. 1996 and 1997 Ford Vehicles: 1. Install the remote start and make the appropriate wire connections on the 555F. 2. Make sure that the 555F capsule can reach the front of the key cylinder where the key is inserted.… Read More

1990-1998 GM Cadillac Deville Ignition Lock Cylinder REMOVAL & INSTALLATION

Filed Under (Cadillac) by admin on 28-03-2014

Download When performing service around Supplemental Inflatable Restraint (SIR) system components or wiring, the SIR system must be disabled. Failure to do so could result in possible air bag deployment, personal injury, or unneeded SIR system repairs. Catera Disconnect the negative battery cable. 1. Remove the steering wheel. 2. Remove the inflatable restraint steering wheel module coil. 3. Insert a small pointed awl or wire into the ignition lock cylinder release pinhole. 4. Pull out the ignition lock cylinder. 5.Fig. Insert a pointed tool into the release pin hole To install: Install the lock cylinder. Look into the hole that receives the lock cylinder on the lower RH side in order to locate the locking lever. 1. Carefully push down on the locking lever using a small flat-bladed tool until an audible click is heard. 2. Place the lock cylinder into the empty hole. 3. 6. Install the inflatable restraint steering wheel module coil.… Read More

1997 – 2001 Infiniti Q45 ENGINE WILL NOT START

Filed Under (Infiniti) by admin on 24-12-2013

Download 2000 – 2001 I30 (CA33) 1999 I30 (CA32) 1999.5 – 2001 QX4 (JR50) 1997 – 2001 Q45 (FY33) 2000 – 2001 G20 (P11) APPLIED VINS: All APPLIED DATES: Start of production SERVICE INFORMATION This bulletin describes and introduces new features of the Infiniti Vehicle Immobilizer System/Nissan Anti-Theft System (IVIS/NATS). The system is standard equipment on each of the applied vehicles listed above. The IVIS/NATS will not allow the engine to start without the use of a registered ignition key. If a vehicle will not start and the Security lamp is on solid, it may be because the ignition keys were not properly registered into the vehicle’s NATS IMMU (Immobilizer control unit). In this case, there will be a “DIFFERENCE OF KEY” code stored in the NATS IMMU. When the NATS ignition key, IMMU, or ECM (ECCS control unit) are replaced, C/U initialization is necessary. It is also necessary when registering keys and as part of many NATS Service Manual diagnostic procedures.… Read More

2003 Kia Rio CYLINDER HEAD Service and Repair

Filed Under (Kia) by admin on 05-03-2014

Download COMPONENT DISASSEMBLY 1. Drain the coolant and disconnect the upper radiator hose. 2. Remove the breather hose (between the air cleaner and the head cover). 3. Remove the air-intake hose. 4. Remove the vacuum hose, fuel hose and coolant hose 5. Remove the cables from the spark plugs . The cables should be removed by holding the boot portion. 6. Remove the ignition coil. 7. Remove the power steering oil pump and bracket. 8. Remove the intake manifold . 9. Remove the heat protector and exhaust manifold assembly. 10. Remove the coolant pump pulley and the crankshaft pulley. 11. Remove the timing belt cover. 12. Remove the timing belt tensioner pulley. 13. Remove the timing belt . 14. Remove the head cover and cam carrier assembly. 15. Remove the cylinder head assembly. The cylinder head bolts should be removed by using Special Tool, Cylinder Head Bolt Wrench, in the sequence as shown in the illustration in two or three steps.… Read More

1996 Chevrolet Chevy K Pickup Ignition Coil Control Circuit High Voltage

Filed Under (Chevrolet (Chevy)) by admin on 21-12-2013

Download 1996 Chevrolet Chevy K Pickup – 4WD | Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual DTC P1351 Ignition Coil Control Circuit High Voltage. Circuit Description The enhanced ignition system uses the crank sensor in order to provide the timing input to the VCM. The VCM uses this reference pulse in order to determine the individual ignition spark timing for each cylinder. Once the VCM calculates the ignition timing, the ignition coil module on the IC circuit receives the timing signal. Each timing pulse received by the ignition coil module on the IC circuit triggers the coil module in order to operate the ignition coil. The secondary ignition voltage is induced, and then the secondary ignition voltage is sent to the distributor for distribution to each spark plug. This DTC is a type A DTC. The IC signal voltage ranges from about 0.5 volt to 4.5 volts.… Read More

Steering Lock Cylinder – Ignition Switch Removing and Installing

Filed Under (Other Manuals) by admin on 09-12-2013

Download Removing – Remove driver’s-side airbag unit and steering wheel. Repair Manual, Body Interior, Repair Group 69 – Remove steering column switches Page 94-37 . – Insert spare or shop key and switch ignition on: access hole will appear in front of switch next to ignition key slot. Installing – Insert length of steel wire or small screwdriver (approx. 2 mm dia.) as far as it will go, as illustrated, and pull lock cylinder out of steering lock housing in direction of arrow. – Ignition switch must be in “ignition on” position. – Push lock cylinder with ignition key all way into steering lock housing and press in firmly until catch engages audibly. – Install steering column switches and steering wheel. Ignition switch, removing and installing Removing Note: It is not necessary to remove the lock cylinder. – Disconnect battery Ground (GND) strap. – Remove driver’s-side airbag unit and steering wheel.… Read More

Various Concerns with Shifter and/or Ignition Key

Filed Under (Other Manuals) by admin on 28-02-2014

Download Models: 2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) Condition Some customers may comment on any of the following concerns: Cause 1 The shifter button may be sticking in the handle. Cause 2 The pin that activates the micro-switch may have moved out of position (refer to illustration above). This causes the micro-switch to fail to engage when the vehicle is placed in Park. If this condition is present, the customer will not be able to remove the key from the ignition. The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter
assembly moves when activating the button.… Read More

Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery

Filed Under (Other Manuals) by admin on 26-12-2013

Download Models: 2004 Buick Rainier 2000-2004 Cadillac Escalade 2002-2004 Cadillac Escalade EXT 2003-2004 Cadillac Escalade ESV 1998-2004 Chevrolet Blazer, S-10 Pickup 1999-2004 Chevrolet Silverado 2000-2004 Chevrolet Suburban, Tahoe 2002-2004 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2004 Chevrolet Express 1998-2004 GMC Jimmy/Envoy, Sonoma 1999-2004 GMC Sierra 2000-2004 GMC Yukon, Yukon XL 2002-2004 GMC Envoy, Envoy XL 2003-2004 GMC Savana 2004 GMC Envoy XUV 1998-2004 Oldsmobile Bravada 2003-2004 HUMMER H2. #04-06-03-002: Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery – (Feb 5, 2004) When diagnosing a concern regarding an intermittent vehicle no crank or dead battery, technicians should remove and reinstall the ignition switch using the Ignition Switch Replacement procedure in the Steering Wheel and Column section of SI. The ignition switch may have been misindexed in the steering column during a previous replacement . If the ignition switch is misindexed in one direction, the ignition switch circuits will not be completely open when the ignition switch is in the OFF position with the key removed.… Read More

555D Honda Prelude Immobilizer Bypass Module Manual Installation Instructions

Filed Under (Honda) by admin on 01-01-2014

Download
Product Description: The Honda Prelude Immobilizer anti-theft system uses a low- power transponder mounted in the head of the ignition key. When the vehicle is started, the Key Cylinder Module converts the transponder signal and sends a secure, coded signal to the Engine Control Module. If the signal to the Engine Control Module is correct, the vehicle will start. The 555D uses a unique automatic program sequence to learn the secure code from the Key Cylinder Module and repeats it when remote start is activated, eliminating the need to leave a key in the vehicle.
Installation Instructions: 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the wiring color guide. 3. Wire the 555D as shown in the wiring diagram.
Wire Connection Guide: ?… Read More

1995 Saturn Wagon Ignition Lock Cylinder

Filed Under (Saturn) by admin on 01-01-2014

Download REMOVAL 1. Remove shroud fasteners (5.5 mm hex head) and remove steering column upper shroud panel. 2. Insert key into ignition lock cylinder and rotate to ACC position. 3. Depress the square locking button on the top of ignition module assembly and slide lock cylinder assembly from ignition module housing. INSTALLATION IMPORTANT : Actuator blade within ignition module housing must be in the ACC position to install lock cylinder assembly. If rotated, replace it to the ACC position using needle nose pliers. Installation is the reverse of Removal.Note: Make sure locking button locks into opening lock cylinder module. Torque steering column lower trim cover bolts to 26 in.lbs. (3 Nm)… Read More

You might also likeclose