Honda Civic D-series Racing Intake Manifold Manual Installation Instructions

Download
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More

2004+ Acura TSX Rear Big Brake Kit Installation Instructions

Download Step 1 Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels For a rear kit installation, block the front wheels, and release the parking brake. Then break loose the lug nuts on both rear wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle. Jack up the vehicle, and secure it on a pair of jack stands, again referring to the Owner’s Manual for jack location joints. After securing the vehicle at a convenient height, remove the rear wheels. Step 2 Disconnect Stock Brake Line Loosen the hard line fitting from the stock brake line, using a 10mm flare wrench. Place a drip tray or several rags directly below the inboard brake line connection. If the area around the brake line connection to the chassis is dirty, clean it using brake cleaner or an appropriate cleaning agent.… Read More

2003 Volvo S40 Replacing The Rear Brake Pads

Download 2003 Volvo S40 L4-1.9L Turbo VIN 27 B4204T4 Vehicle Level Brakes and Traction Control Disc Brake System Brake Pad Service and Repair Rear Brake Pads. Replacing The Rear Brake Pads Special Tools: 999 5782, 951 2834 General CAUTION: Replace the brake pads when the minimum thickness is 2 mm . Removing the rear brake pads Remove * the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers. Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective.… Read More

2007 Volkswagen Rabbit Brake pads, removing and installing

Download 2007 Volkswagen Rabbit BRAKES Brake System. Brake pads, removing and installing Special tools, testers and auxiliary items required. Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! * Remove wheels. * Disconnect connector – 1 – for brake pad wear indicator. * Remove caps – arrows -. * Loosen both guide pins – arrows – and remove from brake caliper. * Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. * Remove brake pads from brake caliper. Cleaning: * Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. * Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir.… Read More

2004+ Acura TSX Front Axle Kit

Download Step 1 Raise Vehicle, and Remove Wheels For a front kit installation, apply the parking brake, then break loose the lug nuts on both front wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle. Jack up the vehicle, and secure it on a pair of jack stands, again referring to the Owner’s Manual for jack location joints. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. After securing the vehicle at a convenient height, remove the front wheels. Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake must be applied before removing the front must be applied before removing the front must be applied before removing the front must be applied before removing the front must be applied before removing the front wheels.… Read More

1995-1996 Honda Civic V 1.4L L4 Part 57-0527 Installation Manual

Download
Honda Civic V 1.4L L4 1995-1996, Honda Civic V 1.4L L4 D14A4 Eng 1997-2001, Honda Civic V 1.6L L4 105BHP 1995-2001 (15.09.10)
1. Unclip and remove air box lid from the vehicle. (Fig. 1) 2. Unbolt & remove the resonator box from the vehicle. (Fig. 2) 3. Disconnect the cam cover breather from the air box base. (Fig. 3) 4. Remove the air temp sensor from the side of the air box. (Fig. 4) 5. Loosen the clip on the throttle neck, unbolt and remove the air box base. (Fig. 5) 6. Remove the 2 short breather hoses from the cam cover outlet and the metal breather hose. (Fig. 6&7) 7. Fit the stepped rubber adaptor onto the throttle housing and firmly tighten using the #44 hose clamp supplied. (Fig. 8) (Note: – This adaptor should be a tight fit) 8. Fit the plastic intake tube into the stepped rubber adaptor & firmly tighten using the #60 hose clamp supplied.… Read More

2007 Honda Accord CR-V and Civic Remote Engine Starter FAQ

Download
Model Information Release date for Accord Remote Starter System: September 20, 2007 Release date for CR-V and Civic Remote Starter System: End of September 2007 Technical Questions Q: What does the Honda Remote Engine Starter System do? A: The Honda Remote Engine Starter is a two-way remote system that starts and stops your vehicle’s engine anywhere within a 200-foot range. It’s designed to warm up your vehicle in the winter and cool it down in the summer. Q: How much is the Honda Remote Engine Starter? A: Approximately $499.00 without installation for all applicable Honda models. Check with your Honda dealer for the installation cost. Q: Can I install it myself? A: AHM does not recommend that customers install the Honda Remote Engine Starter due to the complexity of its electrical components. Authorized Honda Technicians are professionally trained to safely install the Remote Engine Starter. Q: Can I have my neighborhood audio shop install the Honda Remote Engine Starter?… Read More

2003 Honda Accord LX BRAKES Disc and Drum

Download Remove wheels. Thoroughly clean outside of caliper to prevent dust and dirt from entering inside. Support caliper with a piece of wire to prevent damage to brake hose. Remove 2 caliper bolts and caliper from bracket. Remove pad shims and pads. Using vernier calipers, measure the thickness of each brake pad lining. Measurement does not include pad backing plate thickness. See DISC BRAKE SPECIFICATIONS . Remove pad retainers. Inspection Clean caliper thoroughly; remove any rust, and check for grooves and cracks. Check brake disc for damage and cracks. Measure brake pad thickness. See DISC BRAKE SPECIFICATIONS . If brake pad thickness is less than service limit, replace pads as a set. Installation 1. Install pad retainers. Apply Molykote M77 compound onto pad side of shim. Wipe excess grease off shim. Keep grease off discs and pads. Install brake pads and shims. Install inner pad with its wear indicator facing downward.… Read More

1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions

Download
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More