Ford Mustang Fuel Injection Conversion

Download These instructions will provide the basic and necessary information to allow a carbureted 302 to be converted to SEFI Fuel Injection. There are several different types of fuel injection conversions available, however, this instruction will concentrate on the High Output, MASS-AIR setups found on the 92-93 Ford Mustangs. There are two main advantages to using this type of setup. The first advantage is that the computer in the MASS-AIR system will automatically compensate for any engine modifications that have been done prior to the installation of the fuel injection system. The second advantage is that fuel is sent to each cylinder individually only during the appropriate firing cycle, meaning that fuel is sent sequentially to each cylinder only when the spark plug is ready to fire. This makes for an extremely efficient firing cycle . SEFI stands for Sequential Electronic Fuel Injection. This system is complex to be sure, therefore, this instruction is going to skip all the technical mumbo-jumbo, and focus on the bare essentials to install this system properly.… Read More

FORD 429-460 BIG BLOCK ENGINE V8 ENGINE MOUNTS INSTALLATION INSTRUCTIONS

Download KIT CONSISTS OF: No. Qty Part No. Description 1. 1 713014-L DRIVER’S SIDE MOUNT 2. 1 713014-R PASSENGER SIDE MOUNT 3. 2 725002 1/2″-13 LOCK WASHERS 4. 2 725003 1/2″-13 FLAT WASHERS 5. 2 725004 1/2″-13 HEX NUTS 6. 1 FMC001 FORD INSTRUCTION MANUAL. INSTALLATION INSTRUCTIONS: Due to the extreme torque values of the 460 & 429 Ford V8 engines, it will be mandatory that you install a limit strap or straps to the driver’s side and passenger side engine mount. This limiting strap will prevent the engine from torquing beyond the limits of the rubber vulcanization. The straps should be installed with approximately 1/2″ tension reserve. This will permit the engine to torque up to 1/2″ in the motor mount area without causing any problem to the motor mount itself. Warranty on engine mount separation will be void if the limiting straps are not in place. The replacement of the small Ford V8 and straight 6 cylinder engines have become quite popular in Ford trucks.… Read More

FORD F150/250-350: 1987-1996/1998, FORD Ranger: 1993 and up MAZDA B Series: 1994 and up Tailgate Lock PL2300 Installation Instructions

Download Installation 1. Lower the tailgate and remove the access panel with a Torx T-30 driver. 2. Release the rod ends from the plastic clips of the scissor links by prying the yellow clasps up with a screw driver. 3. Remove the two 10 MM nuts holding the scissor bracket and remove it and remove the handle. 4. Pry the plastic dust cover from the handle and discard it. 5. Slide the LOCK BRACKET over the driver’s side stud on the handle and slide the EL over the passenger’s side stud of the handle. 6. Insert them into the tailgate from the outside. 7. Insert the scissor bracket into the tailgate from the inside. Tighten it down with a nut on the driver’s side. 8. Turn the lock counter clockwise with the slot in the horizontal position. This is important for the next step. 9. Insert the BOLT ASSEMBLY and position it onto the driver’s side stud on top of the scissor link with the other nut.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

COMP Cams® Ford Timing Set Installation Instructions

Download Ford Timing Set Installation Instructions Thank you for choosing COMP Cams® products! We know you have options in valve train component selection and we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to review the included limited warranty information. Engine Application High Energy Magnum Hi-Tech Ford V6, 144-200 3223 Ford V6, 171 (2600-2800cc) 3236 Ford V8, 255, 289, 302 & Boss 302, 1965-1988 2120 3120 Ford V8, 289-351W & Boss 302, pre 1972 3220 Ford V8, 302-351W, 1972 & up 3230 Ford V8, 352-428, 1964-1974 3208 2108 3108 Ford V8, 351C, 351M, 400M, 1970-1982 3221 2121 3121 Ford V8, 429-460, 1968-1971 3222 2122 3122 Ford V8, 429-460, 1972-1987 2130 3130 Ford V8, 429-460 w/nine keyway crank gear 2134* Ford V8, 351W, 351W H.O., 1969-¹84 2135 3135 Ford V8, 5.0L 302 H.O., 1980-March 21, 1984 2131 3131 Ford V8, 5.0L 302, 351W, March 22, 1984-1992 2138 3138 Notes: * #2120 or #3120 should not be installed on 351W engines as they are designed for 255, 289, 302 or Boss 302 engines.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

1996 Ford Truck E 350 Van Exhaust Manifold – Exhaust Leaks

Download 1996 Ford Truck E 350 Van V8-460 7.5L Exhaust Manifold – Exhaust Leaks. EXHAUST – EXHAUST LEAK AT EXHAUST MANIFOLDS – VEHICLES EQUIPPED WITH 7.0L OR 7.5L ENGINE LIGHT TRUCK: 1993-96 E-35O 1993-97 F SUPER DUTY, F-250 HD, F-350 MEDIUM/HEAVY TRUCK: 1992-97 F-700, F-800 This TSB article is being republished in its entirety to correct the Labor Operation Times listed. ISSUE An exhaust leak at the exhaust manifolds may be evident on some vehicles. This may be due to heat causing a reduction in bolt torque on the exhaust manifolds. ACTION Install new exhaust manifold bolts. Refer to the following Service Procedure and Part Application Chart for details. SERVICE PROCEDURE NOTE IF THE MANIFOLD IS TO BE RESURFACED, THE BOLTS MUST BE SHORTENED TO ACCOMMODATE THE EXHAUST MANIFOLD . THE BOLTS SHOULD HAVE THE LEADING “DOG POINT” REMOVED TO PREVENT BOTTOMING INTO THE HOLE. NOTE THERE SHOULD NOT BE ANY TYPE OF GASKET USED BETWEEN THE EXHAUST MANIFOLD AND THE CYLINDER HEAD.… Read More

Ford COMP Cams Timing Set Installation Instructions

Download
Engine Application Ford V6, 144-200; Ford V6, 171 (2600-2800cc); Ford V8, 255, 289, 302 & Boss 302, 1965-1988; Ford V8, 289-351W & Boss 302, pre 1972; Ford V8, 302-351W, 1972 & up; Ford V8, 352-428, 1964-1974; Ford V8, 351C, 351M, 400M, 1970-1982; Ford V8, 429-460, 1968-1971; Ford V8, 429-460, 1972-1987; Ford V8, 429-460 w/nine keyway crank gear; Ford V8, 351W, 351W H.O., 1969-¹84; Ford V8, 5.0L 302 H.O., 1980-March 21, 1984; Ford V8, 5.0L 302, 351W, March 22, 1984-1992.
Tools and supplies needed: 1. Basic hand tools as required for your particular camshaft and balancer bolts 2. Torque wrench 3. Pro Cam Lube (part #153 or #154) or suitable replacement 4. Camshaft Degree Kit (part #4796 including degree video) 5. Crankshaft Socket (part #4798 for Ford 302-351W, 429-460) 6. Thread locking compound 7. Engine repair manual for your particular engine.
The following instructions begin after the timing cover and old timing set have been removed.… Read More

Peugeot 306 Roller Bearing Wishbone Bush Kit Installation Guidelines

Download
Installation Part Identification Diagram Please refer to diagramsonthefollowing pagesfor identifying parts and terminology. Installation Front Wishbone Bushes 1. Position one of the new solid bushes, complete with bearing, into the wishbone carrier. Tap it in with a copper hammer. Once you have got itsittingsquare in the wishbone, put the wishbone housingin a vice/pressand windthe bush in until it’s fully seated. It is recommendedyou use some aluminium or wood jaws in the vice to prevent damage to the new bush/bearing. Greasing the bushes before fitting is also a good idea. 2. Now place the spacer bar in the wishbone carrier, soit will sit between the two halves of the front wishbone bush. 3. Now put the remaining bush in, repeating the fitment process as above. 4. Once the bushes are in, when you go to refit the wishbone, you need to fit the washers provided between the subframe housing and the roller bearing in each bush.… Read More

Ford-Toyota-Lexus 555F Interface Module Wiring Installation Instructions

Download The 555F interface module is used when installing remote start products in Ford, Toyota and Lexus vehicles equipped with factory immobilizers. The 555F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. WIRE CONNECTION GUIDE FOR FORDS RED (+)12V: Connect this wire to a fused (+)12V source. BLUE (-) ACTIVATION INPUT: Connect this wire to the (-) through activation output of the remote start system. 555FCAPSULE: The 555F capsule should be placed on the outside of the antenna ring as close to the ribbon cable as possible. LEARNING THE 555F CAPSULE FOR FORDS To program the 555F capsule for a Ford vehicle, use the procedure that corresponds to the appropriate vehicle year. 1996 and 1997 Ford Vehicles: 1. Install the remote start and make the appropriate wire connections on the 555F. 2. Make sure that the 555F capsule can reach the front of the key cylinder where the key is inserted.… Read More