Download 2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Customer Concern: Difficulty filling the gas tank. The pump keeps clicking off. Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted.… Read More
Download TOOLS REQUIRED FOR ASSEMBLY: 7/16″ wrench or socket 3/8″ wrench or socket #2 Phillips screwdriver Tape measure STEP 1: REMOVE CONTENTS & PLYWOOD PACKAGING Remove the canister and top cover from the box. Remove components from inside the canister. Perform a quick inventory to insure all parts are there. Using the wrench or socket remove the 2 bolts holding the plywood packaging supports on the ends of the canister. Discard plywood packaging supports and bolts. Locate the rail guide bolts in the hardware pack and install them in the two holes where the packaging bolts and plywood were just removed. Repeat on both ends of the canister. TOOLS REQUIRED FOR ASSEMBLY: BEFORE YOU START: HARDWARE USED: STEP 2: INSTALL WIRING HARNESS You will need one or two support pieces (We suggest using the top of the box the Bedlocker was shipped in) to set in the truck bed. Set the support piece approximately one foot from the cab.… Read More
Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More
Download 1996-Up Audi / Volkswagen Bose Integration Harness For models amplified without Bose: 1996-03 Audi A4 / 1996-03 Audi A6 2000-01 Audi S4 / 2002-03 Audi S6 Use the White, White/Black, Gray, and Gray/Black speaker wire for the front speaker output and use the Green and Purple RCA’s for the rear speaker outputs. Be sure to connect the Blue/White wire to the aftermarket radio’s amp turn-on wire. The White and Gray RCA’s will not be used. For models amplified with Bose: 1996-03 Audi A4 / 1996-03 Audi A6 1997-03 Audi A8 / 2000-01 Audi S4 2002-03 Audi S6 / 2001-03 Audi S8 2000-03 Audi TT Use the White and Gray RCA’s for the front speaker output and use the Green and Purple RCA’s for the rear speaker outputs. Be sure to connect the Blue/White wire to the aftermarket radio’s amp turn-on wire. The White, White/Black, Gray, and Gray/Black speaker wires will not be used.… Read More
Download TOOLS REQUIRED FOR ASSEMBLY: 7/16″ wrench or socket 3/8″ wrench or socket #2 Phillips screwdriver Tape measure. The Bedlocker is designed to carry rainwater from the cover into the canister and then out through the drains. Most truck models have standard OE drain holes or plastic/rubber access ports in the front of the truck bed. Check to make sure your truck has the OE drain holes so that drilling into the sheet metal is not required. If drilling is necessary, be sure to check the underside of the truck bed for the best location. The holes should be located near the side and as far forward as possible. Use a drill bit suitable for sheet metal (such as a taper drill or step drill). Drill drain tube clearance holes at 3/4″ (19mm). This will need to be done before installing the cover. STEP 1: REMOVE CONTENTS & PLYWOOD PACKAGING Remove the canister and top cover from the box.… Read More
Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More
Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More