". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
OK I removed the line from the charcoal canister to the EVAP purge sensor and blew compresser air through it, no debris. My girlfriend got a face full of compressed.
Chevy Truck Hydraulic Brake Booster. Chevy Pvc Valve Hookup spiritless antagonized soda Chevy Prism Evaporation Canister Assembly. 1995 Chevy Blazer Diagram For Parts.
I may need to replace the EVAP canister vent solenoid valve for my 2007 Chevy Cobalt, 2.2L 4 cyl. The trouble code read: P0446. Where is this part located?.
Filed Under (Hyundai) by Doe Namblas on 02-04-2014
Download 2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Customer Concern: Difficulty filling the gas tank. The pump keeps clicking off. Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted.… Read More
Download 2001 Hyundai Accent Difficulty filling the gas tank. The pump keeps clicking off.
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 31-12-2013
Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More
Download 2004 Chevrolet Chevy K Silverado Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup
Filed Under (Other Manuals) by Doe Namblas on 15-01-2014
Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More
Download Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit
Filed Under (Other Manuals) by Doe Namblas on 17-01-2014
Download DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected Refer to Engine Controls Routing Diagram, EVAP Control System Overview . System Description This DTC tests the evaporative emission (EVAP) system for a small leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the vacuum decay rate. At an appropriate time, the control module turns the EVAP canister purge valve ON and the EVAP vent valve ON. This allows the engine to draw a vacuum on the EVAP system. At a calibrated time, or vacuum level, the control module turns the EVAP canister purge valve OFF, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum decay. If the control module detects a leak larger than a calibrated amount, this DTC sets. The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP canister purge and vent valves.… Read More
Download DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected
Filed Under (Acura) by Doe Namblas on 03-01-2014
Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More
Download 1997-2001 Acura Integra Type-R Racing Intake Manifold
Filed Under (Other Manuals) by Doe Namblas on 08-04-2014
Download Models: 2002 and Prior Passenger Cars and Light Duty Trucks with Non-Enhanced and Enhanced EVAP Systems. Non-Enhanced EVAP System Diagnostic Procedure 1. Pinch off or plug the EVAP vapor line to seal the EVAP system. 2. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground. 3. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part number. 4. Connect the EEST’s nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter. 5. Turn the nitrogen/smoke valve on the EEST control panel to SMOKE. 6. Use the remote switch to introduce smoke into the EVAP system for 60 seconds. Important: Additional smoke may need to be introduced at 15-second intervals until the leak source has been located. 7. Inspect the entire EVAP system for exiting smoke using the high intensity white light (J 41413-SPT).… Read More
Download Test Guidelines for Use of Essential Tool J 41413-200 Evaporative System Tester
Filed Under (Other Manuals) by Doe Namblas on 25-12-2013
Download odels: 1995-1996 Buick Roadmaster 1995-1999 Buick LeSabre 1995-2004 Buick Century, Regal 1995-2005 Buick Park Avenue 1996-1999 Buick Riviera, Skylark 2004-2005 Buick Rainier 1995-1999 Chevrolet Lumina, Monte Carlo, Fullsize Pickup Models (Old Style) 1995-2005 Chevrolet Blazer 1996 Chevrolet Lumina APV 1996-1999 Chevrolet Cavalier 1996-2000 Chevrolet Express Van 1996-2002 Chevrolet Astro Van 1997-2002 Chevrolet Camaro 1997-2003 Chevrolet Malibu 1997-2005 Chevrolet Corvette, Venture 2000-2005 Chevrolet Silverado 2002-2005 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2005 Chevrolet SSR 2004-2005 Chevrolet Classic, Colorado 1995-1999 GMC Fullsize Pickup Models (Old Style) 1995-2002 GMC Jimmy 1996-2000 GMC Savana Van 1996-2002 GMC Safari Van 2000-2005 GMC Sierra 2002-2005 GMC Envoy, Envoy XL 2004-2005 GMC Canyon, Envoy XUV 1995-1999 Oldsmobile Aurora, Eighty Eight 1995-1997 Oldsmobile Cutlass Supreme 1999-2004 Oldsmobile Alero 1998-2002 Oldsmobile Intrigue 1995-1996 Oldsmobile Ninety Eight 1996-1999 Oldsmobile Achieva 1996-2004 Oldsmobile Bravada, Silhouette 1995-1999 Pontiac Bonneville, Sunfire 1995-2002 Pontiac Firebird 1995-2005 Pontiac Grand Prix 1996-1997 Pontiac Trans Sport 1996-2000 Pontiac Grand Am 1997-2005 Pontiac Montana 2003-2005 HUMMER H2.… Read More
Download Information on Error Codes on Radio Display – Their Cause and Corrective Action
Filed Under (Other Manuals) by Doe Namblas on 01-01-2014
Download 1. Turn OFF the ignition. 2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 3. Disconnect the electrical connector. 4. Remove the EVAP vent valve bracket bolt. 5. Remove the EVAP vent valve from the bracket. 6. Disconnect the vent hose from the EVAP vent valve. 7. Remove the EVAP vent valve. Installation Procedure 1. Install the EVAP vent valve on bracket. 2. Connect the vent hose. Canister vent hose should be routed below the fuel tank fill and vent hoses. Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener.… Read More
Download Evaporative Emission (EVAP) Vent Valve Replacement
Filed Under (Ford) by Doe Namblas on 23-01-2014
Download TOOLS REQUIRED FOR ASSEMBLY: 7/16″ wrench or socket 3/8″ wrench or socket #2 Phillips screwdriver Tape measure STEP 1: REMOVE CONTENTS & PLYWOOD PACKAGING Remove the canister and top cover from the box. Remove components from inside the canister. Perform a quick inventory to insure all parts are there. Using the wrench or socket remove the 2 bolts holding the plywood packaging supports on the ends of the canister. Discard plywood packaging supports and bolts. Locate the rail guide bolts in the hardware pack and install them in the two holes where the packaging bolts and plywood were just removed. Repeat on both ends of the canister. TOOLS REQUIRED FOR ASSEMBLY: BEFORE YOU START: HARDWARE USED: STEP 2: INSTALL WIRING HARNESS You will need one or two support pieces (We suggest using the top of the box the Bedlocker was shipped in) to set in the truck bed. Set the support piece approximately one foot from the cab.… Read More
Download FORD FLARESIDE INSTALLATION INSTRUCTIONS
Filed Under (Honda) by Doe Namblas on 01-01-2014
Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More
Download Honda Civic Racing Intake Manifold Installation Instruction